NCCER STUDY GUIDE
EXAM UPDATE.
1. Which organization requires a person to be trained in order to operate personal
lifting equipment? - ✔✔✔ANSWER-OSHA
1. Where would the usage of a RTJ Gasket be found? - ✔✔✔ANSWER-High
Pressure System
All of the following are examples of internal man way hardware except -
✔✔✔ANSWER-Slide Fastener
1. What type of wrench measures how much a fastener is being tightened? -
✔✔✔ANSWER-Torque
1. The fitting that makes it easy to disassemble threaded piping is -
✔✔✔ANSWER-Union
,1. What is the purpose of a gasket? - ✔✔✔ANSWER-TO CREATE A SEAL
BETWEEN 2 STATIONARY PARTS
1. When rigging a valve the sling should be placed around the - ✔✔✔ANSWER-
Body
What is the minimum required oxygen and fuel gas storage separation when not in
use and stored in open area? - ✔✔✔ANSWER-20'
When tightening up a man way on a tower that has ¼" x 8" stud bolts what size
wrench should you use? - ✔✔✔ANSWER-2"
What should a worker do before removing the flange bolts on the exchanged
channel head? - ✔✔✔ANSWER-VERIFY BLINDS ARE IN A BLEEDERS ARE
OPEN AND LOTO
In a piping threading machine equipped with NPT dies is designed to cut which
type of threads? - ✔✔✔ANSWER-NATIONAL PIPE THREADS
Flange protectors should be removed from the valve when - ✔✔✔ANSWER-
READY FOR INSTALLATION
Which sling configuration has the greatest capacity? - ✔✔✔ANSWER-
VERTICAL
To pull a bundle from the shell the eyebolts should be installed on the -
✔✔✔ANSWER-TUBE STEEL
, What is the standard pipe thread used in the USA? - ✔✔✔ANSWER-NPT
After getting a hot work permit, who must be present before starting the work? -
✔✔✔ANSWER-FIRE WATCH
What type of metal would an oxy fuel torch be used to cut? - ✔✔✔ANSWER-
CARBON STEEL
When doing a hydrostatic test, according to the code where should the gauge be
installed on the system? - ✔✔✔ANSWER-HIGHEST POINT
Which of the following is not a purpose of chemically cleaning a vessel? -
✔✔✔ANSWER-TO MAKE WELDS LOOK BETTER
1. All of the following would be reasons for rejecting a sting except? -
✔✔✔ANSWER-ID TAG ON THE WRONG SIDE
1. Which of the special markings on the head of a bolt can be used to determine the
quality of the fastener? - ✔✔✔ANSWER-GRADE
1. What type of tray has a flat perforated plate with a riser or chimney fitted over
each hole and a cap that covers the riser? - ✔✔✔ANSWER-BUBBLE
1. What type of bolt can be used as a lifting device? - ✔✔✔ANSWER-EYE
1. To help control a load, install a - ✔✔✔ANSWER-TAGLINE
EXAM UPDATE.
1. Which organization requires a person to be trained in order to operate personal
lifting equipment? - ✔✔✔ANSWER-OSHA
1. Where would the usage of a RTJ Gasket be found? - ✔✔✔ANSWER-High
Pressure System
All of the following are examples of internal man way hardware except -
✔✔✔ANSWER-Slide Fastener
1. What type of wrench measures how much a fastener is being tightened? -
✔✔✔ANSWER-Torque
1. The fitting that makes it easy to disassemble threaded piping is -
✔✔✔ANSWER-Union
,1. What is the purpose of a gasket? - ✔✔✔ANSWER-TO CREATE A SEAL
BETWEEN 2 STATIONARY PARTS
1. When rigging a valve the sling should be placed around the - ✔✔✔ANSWER-
Body
What is the minimum required oxygen and fuel gas storage separation when not in
use and stored in open area? - ✔✔✔ANSWER-20'
When tightening up a man way on a tower that has ¼" x 8" stud bolts what size
wrench should you use? - ✔✔✔ANSWER-2"
What should a worker do before removing the flange bolts on the exchanged
channel head? - ✔✔✔ANSWER-VERIFY BLINDS ARE IN A BLEEDERS ARE
OPEN AND LOTO
In a piping threading machine equipped with NPT dies is designed to cut which
type of threads? - ✔✔✔ANSWER-NATIONAL PIPE THREADS
Flange protectors should be removed from the valve when - ✔✔✔ANSWER-
READY FOR INSTALLATION
Which sling configuration has the greatest capacity? - ✔✔✔ANSWER-
VERTICAL
To pull a bundle from the shell the eyebolts should be installed on the -
✔✔✔ANSWER-TUBE STEEL
, What is the standard pipe thread used in the USA? - ✔✔✔ANSWER-NPT
After getting a hot work permit, who must be present before starting the work? -
✔✔✔ANSWER-FIRE WATCH
What type of metal would an oxy fuel torch be used to cut? - ✔✔✔ANSWER-
CARBON STEEL
When doing a hydrostatic test, according to the code where should the gauge be
installed on the system? - ✔✔✔ANSWER-HIGHEST POINT
Which of the following is not a purpose of chemically cleaning a vessel? -
✔✔✔ANSWER-TO MAKE WELDS LOOK BETTER
1. All of the following would be reasons for rejecting a sting except? -
✔✔✔ANSWER-ID TAG ON THE WRONG SIDE
1. Which of the special markings on the head of a bolt can be used to determine the
quality of the fastener? - ✔✔✔ANSWER-GRADE
1. What type of tray has a flat perforated plate with a riser or chimney fitted over
each hole and a cap that covers the riser? - ✔✔✔ANSWER-BUBBLE
1. What type of bolt can be used as a lifting device? - ✔✔✔ANSWER-EYE
1. To help control a load, install a - ✔✔✔ANSWER-TAGLINE
