Enphase Storage design certification
training
Which factor of the Ensemble gadget detects a grid failure?
A. Envoy
B. Enpower
C. Encharge - ANSB. Enpower
True or fake: PV structures with Energy storage however without backup energy do not require
Enpower. - ANSTrue
Where do the new conductors between Encharge and Enpower terminate?
A. In the IQ Combiner field
B. At the DER (allotted strength aid) input terminals
C. On the Encharge circuit breaker terminals
D. On the PV circuit breaker terminals
Clear my preference - ANSB. At the DER (distributed power aid) input terminals
What is the most amount of PV and garage that may be connected to the Enpower smart
switch?
A. 80A of PV and 80A of garage for a total of 160A
B. 80A of PV or 80A of garage for a total of 80A
C. 40A of PV and 40A of storage for a complete of 80A
D. 0A, PV and Storage is landed in a backup loads panel - ANSA. 80A of PV and 80A of
storage for a total of 160A
Do we need to put in an extra carrier disconnect if the Enpower principal provider breaker has
been established as the principle service disconnect?
, A. No, it isn't always important to put in an extra disconnect
B. It depends on the use case
C. Yes, it must be redundant and function a rapid shutdown initiation tool - ANSA. No, it isn't
vital to put in an additional disconnect
Why does Enpower want a Neutral Forming Transformer to operate in the course of the grid
outage?
A. Because NEC 2017 calls for a transformer to have connection with Neutral
B. Because Encharge batteries function 240 VAC line to line and cut up segment strength
structures require a impartial
C. Because whilst the grid is down the micro inverters perform on 120 VA - ANSB. Because
Encharge batteries operate 240 VAC line to line and break up section strength systems require
a impartial
The above machine become to start with expected to require three Encharge 3 equal to one
Encharge 10 and no gentle starter. After the site survey, they determined that the most
important single load inside the backup load middle, goes to be a 3 kVA electric motor with a
start modern-day of 32 Amps at 240 VAC for three seconds.
Is the expected length of one Encharge 10 going to be enough to comply with NEC 2017 710.15
(A) with out the use of a gentle starter?
A. Yes, one Encharge 10 will comply
B. One Encharge 10 is adequate due to the fact NEC 2017 710.Five(A) most effective applies to
entire domestic backup
C. No, it calls for at least four Encharge three to comply - ANSC. No, it requires no less than 4
Encharge 3 to conform
For partial home backup the recommendations in the Ensemble planning manual recommend
the dimensions of the energy garage gadget to be the biggest of:
--> Largest single load within the essential loads subpanel
--> Result of load evaluation of strength, surge and reactive power
For whole domestic backup what's delivered to the partial domestic backup listing of items to
extract the most important?
training
Which factor of the Ensemble gadget detects a grid failure?
A. Envoy
B. Enpower
C. Encharge - ANSB. Enpower
True or fake: PV structures with Energy storage however without backup energy do not require
Enpower. - ANSTrue
Where do the new conductors between Encharge and Enpower terminate?
A. In the IQ Combiner field
B. At the DER (allotted strength aid) input terminals
C. On the Encharge circuit breaker terminals
D. On the PV circuit breaker terminals
Clear my preference - ANSB. At the DER (distributed power aid) input terminals
What is the most amount of PV and garage that may be connected to the Enpower smart
switch?
A. 80A of PV and 80A of garage for a total of 160A
B. 80A of PV or 80A of garage for a total of 80A
C. 40A of PV and 40A of storage for a complete of 80A
D. 0A, PV and Storage is landed in a backup loads panel - ANSA. 80A of PV and 80A of
storage for a total of 160A
Do we need to put in an extra carrier disconnect if the Enpower principal provider breaker has
been established as the principle service disconnect?
, A. No, it isn't always important to put in an extra disconnect
B. It depends on the use case
C. Yes, it must be redundant and function a rapid shutdown initiation tool - ANSA. No, it isn't
vital to put in an additional disconnect
Why does Enpower want a Neutral Forming Transformer to operate in the course of the grid
outage?
A. Because NEC 2017 calls for a transformer to have connection with Neutral
B. Because Encharge batteries function 240 VAC line to line and cut up segment strength
structures require a impartial
C. Because whilst the grid is down the micro inverters perform on 120 VA - ANSB. Because
Encharge batteries operate 240 VAC line to line and break up section strength systems require
a impartial
The above machine become to start with expected to require three Encharge 3 equal to one
Encharge 10 and no gentle starter. After the site survey, they determined that the most
important single load inside the backup load middle, goes to be a 3 kVA electric motor with a
start modern-day of 32 Amps at 240 VAC for three seconds.
Is the expected length of one Encharge 10 going to be enough to comply with NEC 2017 710.15
(A) with out the use of a gentle starter?
A. Yes, one Encharge 10 will comply
B. One Encharge 10 is adequate due to the fact NEC 2017 710.Five(A) most effective applies to
entire domestic backup
C. No, it calls for at least four Encharge three to comply - ANSC. No, it requires no less than 4
Encharge 3 to conform
For partial home backup the recommendations in the Ensemble planning manual recommend
the dimensions of the energy garage gadget to be the biggest of:
--> Largest single load within the essential loads subpanel
--> Result of load evaluation of strength, surge and reactive power
For whole domestic backup what's delivered to the partial domestic backup listing of items to
extract the most important?
