10/5/24, 9:01 PM PIPEFITTER EXAM 2024-2025 ACTUAL EXAM COMPLETE QUESTIONS WITH DETAILED VERIFIED ANSWERS (100% C…
PIPEFITTER EXAM 2024-2025 ACTUAL EXAM
COMPLETE QUESTIONS WITH DETAILED
VERIFIED ANSWERS (100% CORRECT
ANSWERS) /ALREADY GRADED A+
Terms in this set (800)
What causes 90% of all Focus Hazards
construction injuries and
deaths and are used to
help OSHA inspectors
improve their
effectiveness?
What is the minimum safe 10 feet
working distance for
overhead power lines?
What is the standard Lockout/Tagout
procedure used to safely
de-energize equipment
on circuits before they
are worked on?
Which of the following is They can be written in any language
not true about Material
Safety Data Sheets?
What are the four focus Fall Hazards, Electrical Hazards, Caught in, Struck
inspections OSHA by
compliance officers look
for?
The sizes of pipe are Nominal pipe size NPS
identified by the
measurement called the:
https://quizlet.com/952763803/pipefitter-exam-2024-2025-actual-exam-complete-questions-with-detailed-verified-answers-100-correct-answers-… 1/10
, 10/5/24, 9:01 PM PIPEFITTER EXAM 2024-2025 ACTUAL EXAM COMPLETE QUESTIONS WITH DETAILED VERIFIED ANSWERS (100% C…
Steel pipe is supplied PESC, T & C TBE
with the following end (All of the above)
finish (es):
What is a typical type of Butt-welded, Socket-welded, Slip-on Flanged (All of
welded pipe joints? the above)
List the four principle Start/Stop, Regulate/Throttle, Relief, Reduce
functions of valves.
Regulating or throttling Both B and C, (globe and gate valve)
flow is done with a:
Name the two basic Lift and Swing
types of check valves.
The most common Clevis
hanger used in piping
systems is the:
Never expose any part of 125°F
a compressed gas
cylinder to temperatures
above:
The four types of copper compression
tube joints are soldered,
brazed, flared and _____?
What is the maximum 350 degrees F
recommended service
temperature when a
brazed joint is used?
Poor alignment of tube spacing difference between tubes and fittings
joints will cause:
After fittings and tubes as soon as possible
are cleaned and fluxed
they should be
assembled and soldered:
Name three basic hitches Straight, Choker, Basket
which can be used for
lifting with a sling
https://quizlet.com/952763803/pipefitter-exam-2024-2025-actual-exam-complete-questions-with-detailed-verified-answers-100-correct-answers-… 2/10
PIPEFITTER EXAM 2024-2025 ACTUAL EXAM
COMPLETE QUESTIONS WITH DETAILED
VERIFIED ANSWERS (100% CORRECT
ANSWERS) /ALREADY GRADED A+
Terms in this set (800)
What causes 90% of all Focus Hazards
construction injuries and
deaths and are used to
help OSHA inspectors
improve their
effectiveness?
What is the minimum safe 10 feet
working distance for
overhead power lines?
What is the standard Lockout/Tagout
procedure used to safely
de-energize equipment
on circuits before they
are worked on?
Which of the following is They can be written in any language
not true about Material
Safety Data Sheets?
What are the four focus Fall Hazards, Electrical Hazards, Caught in, Struck
inspections OSHA by
compliance officers look
for?
The sizes of pipe are Nominal pipe size NPS
identified by the
measurement called the:
https://quizlet.com/952763803/pipefitter-exam-2024-2025-actual-exam-complete-questions-with-detailed-verified-answers-100-correct-answers-… 1/10
, 10/5/24, 9:01 PM PIPEFITTER EXAM 2024-2025 ACTUAL EXAM COMPLETE QUESTIONS WITH DETAILED VERIFIED ANSWERS (100% C…
Steel pipe is supplied PESC, T & C TBE
with the following end (All of the above)
finish (es):
What is a typical type of Butt-welded, Socket-welded, Slip-on Flanged (All of
welded pipe joints? the above)
List the four principle Start/Stop, Regulate/Throttle, Relief, Reduce
functions of valves.
Regulating or throttling Both B and C, (globe and gate valve)
flow is done with a:
Name the two basic Lift and Swing
types of check valves.
The most common Clevis
hanger used in piping
systems is the:
Never expose any part of 125°F
a compressed gas
cylinder to temperatures
above:
The four types of copper compression
tube joints are soldered,
brazed, flared and _____?
What is the maximum 350 degrees F
recommended service
temperature when a
brazed joint is used?
Poor alignment of tube spacing difference between tubes and fittings
joints will cause:
After fittings and tubes as soon as possible
are cleaned and fluxed
they should be
assembled and soldered:
Name three basic hitches Straight, Choker, Basket
which can be used for
lifting with a sling
https://quizlet.com/952763803/pipefitter-exam-2024-2025-actual-exam-complete-questions-with-detailed-verified-answers-100-correct-answers-… 2/10
