• Wrong document? Swap it for free
  • Written by students who passed
  • Immediately available after payment
  • Read online or as PDF
Sell
Where do you study
Your language
Document preview thumbnail
Preview 1 out of 3 pages
Exam (elaborations)

Nocti Engineering Pt2

Document preview thumbnail
Preview 1 out of 3 pages

Which of the following indicators is used to denote the center of a circle? - answer-+ What is the third color band on a resistor represents? - answer-The first and second band represent the numerical value of the resistor, and the color of the third band specify the power-of-ten multiplier. The fourth represents the tolerance. The color bands are always read from left to right starting with the side that has a band closer to the edge. Identifying leader in the assembly process in order to routinely compare one's processes and outputs to the leader is called - answer-Performance matching When energized a solenoid actuates upon which of the following objects: - answer-Steel Which statement best describes precision alignment? - answer-It corrects any defects in the shaft The most important factor for an engineer in selecting a project solution should be - answer-Safety Healthier staff, increased attendance and productivity, increased morale, and reduced litigation risks are some of the advantages of adhering to what regulations? - answer-OSHA An international body of technical standards for various industries, designed to promote international trade, engineering conformance, and most recently environmental awareness is known of - answer-International organizations for standardization When determining the degree of acceptable risk in a project, an engineer should always consider - answer-A cost/ risk / benefit analysis Training and _____ may be given to comply with OSHA in the workplace - answer-Teamwork A good method of maintain a safe work area is to maintain a clean work bench, attend safety meetings and - answer-Abide by safety signs Performing engineering functions, ethical conduct is the responsibility of the - answer-Individual engineer Immediately report the malfunction of any piece of equipment - answer-Safety engineer The _________ code defines requirements when joining metals using the MIG process - answer-AWS Since 1971, when _____ was created, occupational deaths have been cut by 62 percent and injuries have declined by 42 percent - answer-OSHA When a gas cylinder is at work station , as safety precaution, - answer-At least two inches off flow Because switches can fail after opening a disconnect, safest practice is to - answer-Lock and dag the disconnect For the sake of maintaining good safety practices, never use an ohmmeter on a circuit that might be - answer-Energized When testing with compressed air, caution should be given to the _____________ used. - answer-Pounds per square inch of a gauge Install surge protection on electrical equipment to - answer-Shield equipment from sudden power increases. A _______switch opens when current exceeds predetermined safety level. - answer-Fuse What is the name for the international body of technical standard for various industries, designed to promote international trade, engineering conformance and environmental awareness? - answer-International Organization for Standardization Which of the following drawing methods is used to generate a 2D Multiview drawing - answer-Orthographic Which of the following drawing methods generates a pictorial drawing? - answer-Orthographic This process may use techniques including constructive solid geometry, implicit surfaces, subdivision surfaces to shape individual objects, and placement of various spots on more xyz grids that are mapped out. Changing one or more variables might result in updating related graphics. This process is known as - answer-3D modeling Of the following, Which lines indicate a hidden edge - answer-_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ What is an oblique, isometric perspective orthographic drawing method? Which one will generate a 2D Multiview drawing? - answer-Oblique: type of technical drawing of graphical projection used for producing two-dimensional images of three-dimensional objects. The objects are not in perspective, so they do not correspond to any view of an object that can be obtained in practice. Isometric: a method for visually representing three-dimensional objects in two dimensions in technical and engineering drawings. It is an axonometric projection in which the three coordinate axes appear equally foreshortened and the angle between any two of them is 120 degrees. An orthographic drawing represents a three-dimensional object using several two-dimensional views of the object. It is also known as an orthographic projection. What is the meaning of OEM? - answer-Original Equipment Manufacturing Manufacturing product quality control includes - answer-Production flow chart The following process of converting raw materials to finished products is - answer-Manufacturing Typical gas pressure gauges will read_______ at atmospheric pressures. - answer-100kPa Undercutting is a condition that generally occurs when the - answer-When the welding current is too high A means of monitoring the assembly and fabrication process by gathering data and samples to evaluate variations in the process that may impact the final

Content preview

NOCTI ENGINEERING PT2
Which of the following indicators is used to denote the center of a circle? -
answer-+

What is the third color band on a resistor represents? - answer-The first and
second band represent the numerical value of the resistor, and the color of
the third band specify the power-of-ten multiplier. The fourth represents the
tolerance. The color bands are always read from left to right starting with the
side that has a band closer to the edge.

Identifying leader in the assembly process in order to routinely compare
one's processes and outputs to the leader is called - answer-Performance
matching

When energized a solenoid actuates upon which of the following objects: -
answer-Steel

Which statement best describes precision alignment? - answer-It corrects
any defects in the shaft

The most important factor for an engineer in selecting a project solution
should be - answer-Safety

Healthier staff, increased attendance and productivity, increased morale,
and reduced litigation risks are some of the advantages of adhering to what
regulations? - answer-OSHA

An international body of technical standards for various industries, designed
to promote international trade, engineering conformance, and most recently
environmental awareness is known of - answer-International organizations
for standardization

When determining the degree of acceptable risk in a project, an engineer
should always consider - answer-A cost/ risk / benefit analysis

Training and _____ may be given to comply with OSHA in the workplace -
answer-Teamwork

A good method of maintain a safe work area is to maintain a clean work
bench, attend safety meetings and - answer-Abide by safety signs

Performing engineering functions, ethical conduct is the responsibility of the
- answer-Individual engineer

Document information

Uploaded on
September 16, 2024
Number of pages
3
Written in
2024/2025
Type
Exam (elaborations)
Contains
Questions & answers
$11.49

Wrong document? Swap it for free Within 14 days of purchase and before downloading, you can choose a different document. You can simply spend the amount again.
Written by students who passed
Immediately available after payment
Read online or as PDF

Seller avatar
Reputation scores are based on the amount of documents a seller has sold for a fee and the reviews they have received for those documents. There are three levels: Bronze, Silver and Gold. The better the reputation, the more your can rely on the quality of the sellers work.
TOPDOCTOR
5.0
(1)
Sold
10
Followers
5
Items
3387
Last sold
1 year ago



Why students choose Stuvia

Created by fellow students, verified by reviews

Quality you can trust: written by students who passed their tests and reviewed by others who've used these notes.

Didn't get what you expected? Choose another document

No worries! You can instantly pick a different document that better fits what you're looking for.

Pay as you like, start learning right away

No subscription, no commitments. Pay the way you're used to via credit card and download your PDF document instantly.

Student with book image

“Bought, downloaded, and aced it. It really can be that simple.”

Alisha Student

Working on your references?

Create accurate citations in APA, MLA and Harvard with our free citation generator.

Working on your references?

Frequently asked questions