Forklift Study Guide With Complete Solution
Which of the following options is an approved use for a forklift
a) lift a vehcle
b) lift a load
c) lift another forklift
d) lift someone - ANSWER-b) lift a load
The three-point suspension system that supports the forklift is referred to as the:
a) stability triangle
b) data plate
c) forklift diagram
d) mast - ANSWER-a) stability triangle
the maximum load capacity of a forklift must be based on the _______ of any parts of
the forklift
a) greatest maximum capaity
b) lowest maximum capacity
c) width
d) height - ANSWER-b) lowest maximum capacity
the _____ is the part of the forklift that maneuvers the load by lifting, lowering, and
positioning
a) center of gravity
b) fork
c) mast
d) front axle - ANSWER-c) mast
Before operating a forklift, check the _____ for the forklift"s maximum capacity and
other essential information about the forklift
a) operator restraints
b) data plate
c) backrest retraints
d) overhead gaurd - ANSWER-b) data plate
forklifts that utilize cushion tires ______
a) are higher to the ground
b) are lower to the ground
, c) require internal combustion engines
d) require an electric power source - ANSWER-a) are lower to the ground
you are on a construction site and will be working on steep slopes in addition to
frequently transporting materials to other sites. which forklift class is best suited for this
scenario?
a) class 1 electric motor rider cushion-tired truk
b) class ll electric motor narrow aisle truck
c) class iv internal combustion engine truck
d) class vii rough terrain truck - ANSWER-d) class vii rough terrain truck
using an ____________ forklift presents an increased risk of exposure to exhaust
fumes. - ANSWER-a) internal combustion engine
class 1 ________ tired forklifts are designed for indoor usage on smooth surfaces
a) pneumatic
b) cushion
c) large
d) small - ANSWER-b) cushion
when operating a class lll electric motor hand truck, the operator ______
a) uses the controls in the back of the forklift
b) uses the controls of the bottom of the tiller
c) stands in front of the forklift
d) stands behind the forklift - ANSWER-c) stands in front of the forklift
before operating your forklift, you check the weight and height of he material and see
that it exceeds your forklift"s capacity. what should your next step be to ensure you can
safely transfer the load?
a) operate in reverse while transporting the material
b) lift the forks so they are higher than 4 inches from the ground
c) ensure you will not be operating on rough terrain
d) break the material into smaller loads before transporting it - ANSWER-d) break the
material into smaller loads before transporting it
which of the following is true about braking while operating a forklift on smooth
surfaces?
a) smooth surfaces require pneumatic tires to brake easily
b) smooth surfaces allow you to brake faster
c) smooth surfaces will create less friction, making it harder to brake
d) smooth surfaces create too much friction while braking - ANSWER-c) smooth
surfaces will create less friction, making it harder to brake
Which of the following options is an approved use for a forklift
a) lift a vehcle
b) lift a load
c) lift another forklift
d) lift someone - ANSWER-b) lift a load
The three-point suspension system that supports the forklift is referred to as the:
a) stability triangle
b) data plate
c) forklift diagram
d) mast - ANSWER-a) stability triangle
the maximum load capacity of a forklift must be based on the _______ of any parts of
the forklift
a) greatest maximum capaity
b) lowest maximum capacity
c) width
d) height - ANSWER-b) lowest maximum capacity
the _____ is the part of the forklift that maneuvers the load by lifting, lowering, and
positioning
a) center of gravity
b) fork
c) mast
d) front axle - ANSWER-c) mast
Before operating a forklift, check the _____ for the forklift"s maximum capacity and
other essential information about the forklift
a) operator restraints
b) data plate
c) backrest retraints
d) overhead gaurd - ANSWER-b) data plate
forklifts that utilize cushion tires ______
a) are higher to the ground
b) are lower to the ground
, c) require internal combustion engines
d) require an electric power source - ANSWER-a) are lower to the ground
you are on a construction site and will be working on steep slopes in addition to
frequently transporting materials to other sites. which forklift class is best suited for this
scenario?
a) class 1 electric motor rider cushion-tired truk
b) class ll electric motor narrow aisle truck
c) class iv internal combustion engine truck
d) class vii rough terrain truck - ANSWER-d) class vii rough terrain truck
using an ____________ forklift presents an increased risk of exposure to exhaust
fumes. - ANSWER-a) internal combustion engine
class 1 ________ tired forklifts are designed for indoor usage on smooth surfaces
a) pneumatic
b) cushion
c) large
d) small - ANSWER-b) cushion
when operating a class lll electric motor hand truck, the operator ______
a) uses the controls in the back of the forklift
b) uses the controls of the bottom of the tiller
c) stands in front of the forklift
d) stands behind the forklift - ANSWER-c) stands in front of the forklift
before operating your forklift, you check the weight and height of he material and see
that it exceeds your forklift"s capacity. what should your next step be to ensure you can
safely transfer the load?
a) operate in reverse while transporting the material
b) lift the forks so they are higher than 4 inches from the ground
c) ensure you will not be operating on rough terrain
d) break the material into smaller loads before transporting it - ANSWER-d) break the
material into smaller loads before transporting it
which of the following is true about braking while operating a forklift on smooth
surfaces?
a) smooth surfaces require pneumatic tires to brake easily
b) smooth surfaces allow you to brake faster
c) smooth surfaces will create less friction, making it harder to brake
d) smooth surfaces create too much friction while braking - ANSWER-c) smooth
surfaces will create less friction, making it harder to brake
