Aircraft general knowledge
How are the cylinders arranged in a piston engine? - answer-horizontally opposed What are the parts of an engine? - answer-- cylinder - piston - camshaft - connecting rod - spark plug - intake manifold/valve - exhaust valve - outlet manifold - connecting rod What is the camshaft used for and how does it work? - answer-The camshaft is used for valve timing. It works by operating rocker arms and push rods that open the appropriate valve at the most suitable time in the cycle. What does the crank shaft do? - answer-drives the camshaft What are the two types of mixture controls? - answer-- needle type - back suction type What are the 4 strokes of the OTTO cycle? - answer-1. Intake (induction) 2. Compression 3. power (combustion) 4. exhaust What happens during these stages and when do they occur? - answer-1. The intake stage begins as soon as the inlet valve opens until it closes, It also occurs 10 degrees before TDC and 40 degrees after BDC. The piston travels down and the fuel air mixture is introduced into the intake valve. 2. Compression stage begins from the time the inlet valve closes till the ignition of the charge. Beings 40 degrees after BDC till 25 degrees before TDC. The piston travels up compressing the fuel air mixture. 3. Power (combustion) stage begins from the ignition of the spark till the exhaust valve opens. 25 degrees before TDC and 50 degrees before bottom dead center. The pressure of combustion forces the piston down the barrel. 4. Exhaust stage begins from the time the exhaust valve opens till it closes. The piston is forced back up the barrel expelling the gases though the exhaust valve. 50 degrees before BDC till 10 degrees after TDC. What does power output of the engine depend on? - answer-The amount of gas in the cylinders and the temperature reached. What are the different types/set ups of engines? - answer-- radial engine (pistons arranged around the crankshaft) - inline inverted - inline upright - Vee - horizontally opposed What is complete combustion? - answer-Combustion which occurs at the stoichieometric ratio of 15 (parts air): 1 (part fuel) What is detonation? - answer-Spontaneous explosive combustion What causes detonation? - answer-high cylinder head temperatures, expired or incorrect fuel grades, over lean mixtures What are the symptoms of detonation? - answer-- high and increasing cylinder head temperatures - power loss - engine vibration and pinging noise What is pre-ignition? - answer-fuel/air mixture ignites before the spark plug fires. What can cause pre-ignition? - answer-hot spots in the cylinder, high powers with a lean mixture and over heated spark plugs. What are the different types of Aircraft fuel systems? - answer-- gravity fed - pressure pump fed What are the different types of Engine fuel systems? - answer-- carburetors - fuel injection What are the components of the fuel system? - answer-- fuel tank vent - strand pipe - fuel selector - fuel shut off valve - fuel quantity gauge what is the function of a carburetor? - answer-It mixes the fuel air mixture for delivery to the engine. What are 3 types of carburetor icing? - answer-- impact ice - fuel evaporation ice - throttle ice What are the main reasons for a temperature drop? - answer-- the fuel evaporation process - pressure drop in the venturi What is impact ice? - answer-super-cooled water droplets freeze on impact with components in the carburetor. When is carburetor ice most likely to occur? - answer-at low power on long descents. What and why is the accelerator pump used? - answer-When the throttle is opened quickly the fuel, as it is heavier, moves slower than the air. In order to provide the fuel to the cylinders simultaneously the accelerator pump supplies a surge of fuel for a continuous supply allowing for smooth acceleration. How is the fuel injection system different to the carburetor? - answer-It supplies the fuel directly to the cylinders What is one of the disadvantages of the fuel injection system and how does it occur? - answer-Fuel vaporisation This occurs when the fuel in liquid form begins to turn into vapour and becomes trapped in the fuel lines How can fuel vaporisation be rectified? - answer-using the electric boost pump What is oil used for? - answer-- lubrication - cooling - cleaning - protection - sealing What is viscosity? - answer-The characteristic flow of oil What is the propeller blade angle? - answer-The angle between the plane of rotation and chordline What are the components of the total reaction? - answer-Thrust and torque What does propeller torque act to overcome? - answer-the motion of the propeller blades What does the engine torque act to overcome? - answer-the propeller torque what are the characteristics of a coarse pitch? - answer-A larger blade angle and large geometric pitch What are the characteristics of a fine pitch? - answer-small blade angle and small geometric pitch When is coarse pitched most likely to be used? - answer-high air speeds and in cruise If you alter the TAS with a constant rpm, how will this affect the AoA? - answer-an increase in TAS will decrease the AoA, a decrease in TAS will increase the AoA If you alter the rpm with a constant TAS, how will this affect the AoA? - answer-An increase in rpm will increase the AoA, a decrease in rpm will decrease the AoA. What is an aerodynamic twisting moment (ATM)? - answer-it is a force that acts to twist the blade towards coarse pitch What is a centrifugal twisting moment (CTM)? - answer-a force that attempts to
Document information
- Uploaded on
- July 1, 2024
- Number of pages
- 6
- Written in
- 2023/2024
- Type
- Exam (elaborations)
- Contains
- Questions & answers