Dante Level 2 (2023/2024) Questions and Answers 100% Pass

Dante Level 2 (2023/2024) Questions and Answers 100% Pass Dante Controller can recall part of a preset - only storing information about some settings and/or limiting which devices we want to recall them on. True What advantages does unicast have over multicast communication? (Select 3.) Unicast is simpler to deliver, reducing the strain on the switch. Unicast can achieve lower latency than multicast. (Minimum latency for multicast is 1msec.) Unicast can cross a router, multicast cannot. A multicast subscription is made between two Dante devices. The latency value of the transmitter and receiver are 0.25msec and 0.5msec, respectively. What is the resulting latency of this stream? 1.0 msec When a Dante preset is saved, where is the information kept? Dante Controller writes a text file (XML format) to the computer. This file can be shared to other users or archived for recall later. When the preset is recalled, Dante Controller systematically restores all settings, one at a time. What happens if multiple devices have the Preferred Leader checkbox marked? Both will be elevated in the clock election process, only one of those two will be come the clock leader. HC and IP Core I/Os 512x512 Broadway I/Os 16x16 Brooklyn II I/Os 64x64 Ultimo-X I/Os 4x0,2x2,0x4 PCIe Card I/Os 128x128 Dante AV I/Os 8x8 For Dante AV, up to X video channel(s) and up to Y audio channel(s) are available. The chipset can Z. For Dante AV, up to [ 1 ] video channel(s) and up to [ 8 ] audio channel(s) are available. The chipset can be configured as an input or output. If a transmitting device runs out of flows, what should you do to enable all subscriptions to be made? Flip stream(s) to multicast so it only takes one flow for multiple destinations. Dante Controller can apply information in a Dante preset to a device of a different model. For instance, if a 4-channel 70V amplifier is replaced with an 8-channel model, it could save the IP settings, device name, as well as channel labels and subscriptions for the first four channels True A unicast audio or video subscription: IS the default behavior for Dante devices Suppose a Dante device that is chasing an external clock (like word clock or video sync). What setting must be checked in Dante Controller? In Dante Controller, make sure the "External Clock" checkbox is marked for this device. The redundant port allows for a second network connection in case the first fails. Which describes the operation? The primary and secondary operate full time in separate broadcast domains. If the connection fails on one network, it will continue to the other. If a Dante device is in redundant mode, can the ports use different configuration methods? For instance, can the primary port be set to a Static IP and the secondary follow Link Local? Yes Which Dante software supports redundant connections? Dante Controller The Dante clock leader election is an automatic process. However, you can manually influence the winning device(s). Which is the highest tier? Preferred Leader Checked How many audio channels can be contained in a Dante unicast flow? 4 What protocol does Dante for clocking? PTP What is the "golden rule" about Dante redundant networks? Do not link the primary and secondary networks - they must remain in separate broadcast domains. Since the beginning of Dante, multicast flows could carry X channels per flow. With newer firmware, multicast flows can carry up to Y channels per flow. Since the beginning of Dante, multicast flows could carry 8 channels per flow. With newer firmware, multicast flows can carry up to 64 channels per flow. As a simple rule of thumb, how much latency should be allowed per network switch hop? 0.1 msec (100 microseconds) Suppose a Dante device has one channel and two transmit flows. Can it connect to three different receiving devices? Yes. The channel must be sent as multicast. Can a Dante network with five switch hops support latency of 1 msec? Yes. Minimum recommended latency could be as low as 0.5 msec. A unicast subscription is made between two Dante devices. The latency value of the transmitter and receiver are 0.25msec and 0.5msec, respectively. What is the resulting latency of this stream? 0.5 msec Approximately how much bandwidth does a unicast audio flow use? (4-ch, 24-bit, 48kHz, 1msec latency) 6Mbps