Mark's API 510 Questions & Answers STUDY GUIDE 2023/24 Update

Mark's API 510 Questions & Answers STUDY GUIDE 2023/24 Update Mark's API 510 STUDY GUIDE Which of the following activities is NOT included in the scope of API 510? - A) rerating a vessel - B) Operating a vessel. - C) replacing a vessel head - D) internally inspecting a vessel - ANSWERB Which of the following activities is NOT included in the scope of API 510? - A) setting relief device intervals - B) performing vessel alterations - C) Performing vessel fabrication - D) performing vessel maintenance - ANSWERC Which of the following equipment types is NOT covered by API 510? a) Heats exchanger b) Safety relief valve c) Distillation column d) Process heater (furnace) - ANSWERD API 510 can be used: a) only by refining industries b) only by chemicals c) only by petrochemical industries d) By petro-chemical facilities and other industry. - ANSWERD API 510 takes effect: a) During the design stage of the vessel construction. b) During the fabrication stage of the vessel construction. c) Once the fabrication hydro or pneumatic test is completed d) Once the nameplate is attached e) Once the vessel is placed in service. f) Once the vessel has an operation problem - ANSWERE API 510 covers vessels constructed to which fabrication code(s)? a) only ASME B&PV Sect.VIII b) only ASME & PV Sect.VIII and the API / ASME code for Unfired Pressure Vessels c) ASME B&PV Sect.VIII and other current codes d) Any fabrication code. - ANSWERD When does API 510 stop applying to vessels? a) In-service but have proven they do not corrode b) In-service and the corrosion rate is less than 0.005 ipy c) Out of service, but stored for a future service d) Retired and abandoned e) Retired, removed and scrapped - ANSWERD During repairs & alterations most of the code requirements come from: a) API 510 b) ASME SECTION VIII c) ASME Section VIII or the construction code. d) The construction code - ANSWERC During a vessel repair, if there is a conflict between the requirements of API 510 and the construction code which should be followed? a) API 510 b) The construction code c) Either code based on the Inspector's recommendation d) The code with the most stringent requirements - ANSWERA During a vessel alteration, if there is a conflict between the requirements of API 510 and the construction code which should be followed? a) API 510 b) The construction code c) Either code based on the Inspector's recommendation d) The code with the most stringent requirements - ANSWERA Companies that use API 510 must: a) Employ an authorized inspection agency b) Have access to an authorized inspection agency c) Either employ or have access to an authorized inspection agency. d) Employee professional engineers e) Pay all API 510 contract inspectors $62.50 / hr - ANSWERC Which of the following individuals must be directly employed by the Owner? a) Authorized Inspector b) Examiner c) Pressure Vessel Engineer d) Repair Organization e) No one - all can be contracted personnel. - ANSWERE Who is responsible for responding to inspection results that require corrective action? a) Engineer b) Maintenance Department c) Owner / User d) Pressure Equipment Specialist - ANSWERC An in-service vessel is being repaired or altered. If there is a conflict between the requirements of API 510 and the legal jurisdiction, which should be followed? a) API 510 b) The Legal Jurisdiction c) The one with the most stringent requirements. d) Either set of the requirements based on Engineer and AI approval - ANSWERC An in-service vessel is inspected. If there is a conflict between API 510 and the legal jurisdiction, which should be followed? a) API 510 b) The Legal Jurisdiction c) The one with the most stringent requirements d) Either set of the requirements based on Engineer and AI approval - ANSWERC Which of the following vessels, that may be exempted from API 510, should be considered for inclusion in the Owner/User's API 510 program? a) 140' Low Pressure Storage Tank b) Oil Mist Accumulator c) Small Filter d) Vacuum Flasher - ANSWERD Which code is used for Fitness for Service evaluations? a) API 579 b) API 660 c) API 2201 d) ASME B&PV Section V - ANSWERA Which code is used for RBI assessments? a) API 573 b) API 579 c) API 580 d) API 2201 - ANSWERC During an in-service internal inspection, a crack is discovered on a longitudinal weld. This crack can be evaluated to which industry document? a) API 510 b) API 579 c) ASME B&PV Section VI d) Cracks are never allowed in an in-service vessel. - ANSWERB Which document provides requirements for Hot Tapping? a) API 578