• Wrong document? Swap it for free
  • Written by students who passed
  • Immediately available after payment
  • Read online or as PDF
Sell
Where do you study
Your language
Document preview thumbnail
Preview 2 out of 11 pages
Exam (elaborations)

Millwright Manual Alignment Test Solved 100%

Document preview thumbnail
Preview 2 out of 11 pages

Why are machines accurately aligned with each other? 23:1 - Answer Machines are accurately aligned to work together smoothly. Thus increasing working life. How is the Primary unit positioned? 23:1 - Answer The primary unit is positioned according to reference lines (centre-lines, benchmarks etc) What are the other machines aligned with the Primary unit? 23:1 - Answer Drive units; prime movers, transmission units etc. Are usually aligned with the primary unit. How is an alignment procedure chosen? 23:2 - Answer The alignment procedure used is determined by the type of components connecting the units. What procedure is used to align coaxial shafts? 23:2 - Answer In-line (coaxial shafts) are usually alogned with couplings in a procedure called coupling alignment. What are the results of coaxial misalignment? 23:2 - Answer Results of coaxial misalignment are: -reduced bearing life -coupling damage -high vibration -reduced seal life -increased downtime and costs What conditions of misalignment are present in misaligned coaxial shafts? 23:2 - Answer -offset -angular To align shafts correctly, in what two planes must these conditions be solved? 23:2 - Answer Shafts must be align in both horizontal & vertical planes Why is vertical alignment corrected first? 23:3 - Answer Because it is very easy to disturb horizontal alignment when correcting the vertical alignment. How is vertical misalignment corrected? 23:3 - Answer By using shims underneath the machine feet How is horizontal alignment corrected? 23:3 - Answer By adjusting the position of the unit on its base with jacking screws Define angular misalignment. 23:3 - Answer Angular misalignment occurs when the coupling faces are not parallel with each otheras well as the shaft centre-lines. How is angular misalignment corrected horizontally & vertically? 23:3 - Answer Horizontal: jacking screws Vertical: correct amount of shims under front and back shims. Define offset misalignment. 23:3 - Answer When the centre-lines of both shafts are parallel but not in-line. How is offset misalignment corrected horizontally? 23:3 - Answer By moving jacking screws on one side evenly till shafts are in-line. How is offset misalignment corrected vertically? 23:3 - Answer By adding or removing an equal amount of shims from all feet to bring shafts in-line. Describe combination misalignment. 23:4 - Answer Combination misalignment occurs when both angular & offset misalignment are present between coaxial shafts. Define Softfoot. 23:4 - Answer Softfoot occurs when a machines feet do not equally support its weight; it does not sit firmly on all feet. How does softfoot effect the machine? 23:4 - Answer Softfoot will stress the machine housing and ovalize bearing bores. What causes Softfoot? 23:4 - Answer Softfoot can be caused by: -poorly machined feet -dirt under feet -in-correct anchor bolt torque -poor levelling -poor base design -grout deteriation -base or foot corrosion What are the two types of Softfoot? 23:4-5 - Answer -ordinary softfoot -angular softfoot What is a good foot-to-base fit? 23:4-5 - Answer Gap between foot and base should be less than 0.001" (0.025mm) How does thermal expansion & contraction affect alignment? 23:5 - Answer Thermal expansion and contraction will cause misalignment to develope as a machine warms up to or cools down from operating temperature.


Document information

Uploaded on
September 9, 2023
Number of pages
11
Written in
2023/2024
Type
Exam (elaborations)
Contains
Questions & answers
$13.49

Wrong document? Swap it for free Within 14 days of purchase and before downloading, you can choose a different document. You can simply spend the amount again.
Written by students who passed
Immediately available after payment
Read online or as PDF

Seller avatar
Reputation scores are based on the amount of documents a seller has sold for a fee and the reviews they have received for those documents. There are three levels: Bronze, Silver and Gold. The better the reputation, the more your can rely on the quality of the sellers work.
Grademasters
3.8
(46)
Sold
118
Followers
69
Items
2591
Last sold
1 month ago




Why students choose Stuvia

Created by fellow students, verified by reviews

Quality you can trust: written by students who passed their tests and reviewed by others who've used these notes.

Didn't get what you expected? Choose another document

No worries! You can instantly pick a different document that better fits what you're looking for.

Pay as you like, start learning right away

No subscription, no commitments. Pay the way you're used to via credit card and download your PDF document instantly.

Student with book image

“Bought, downloaded, and aced it. It really can be that simple.”

Alisha Student

Working on your references?

Create accurate citations in APA, MLA and Harvard with our free citation generator.

Working on your references?

Frequently asked questions

Whoops! We can’t load your doc right now. Try again or contact support.