• Wrong document? Swap it for free
  • Written by students who passed
  • Immediately available after payment
  • Read online or as PDF
Sell
Where do you study
Your language
Document preview thumbnail
Preview 2 out of 12 pages
Exam (elaborations)

Millwright Practice Exam 2 Already Solved 100%

Document preview thumbnail
Preview 2 out of 12 pages

unusual - Answer If the seal was not properly aligned or there is excessive wear in some bearing or shaft,_______ wear tracks will be the indicator sharpened brass putty knife - Answer For removing hard to remove gasket materials found on sealing surfaces, ______ is recommended Conducted on the job - Answer Apprenticeship training is_______ distance - Answer Charting alignment on a graph requires a chart that is divided into thousandths of an inch vertically for the indicator readings and into whole inches horizontally for the__________ hidden - Answer The orthographic drawing may contain a dashed or _______ line Radiation - Answer In order to shoot through a test object and project an image onto a detector or a sheet of film, radiography uses a source of penetrating called _______ *scribe circles *transfer measurements *compare distances measure angles - Answer Which of the following task would you not perform with dividers? 10% - Answer The over speed trip device is actuated when the turbine reaches a predetermined limit usually _________% above normal full-load speed high - Answer Positive results in an offset measurement mean that the MTBM is _____ or on the 3-o'clock side. offset misalignment - Answer The coupling gap is set, and then the ______ is measured pressure - Answer In a hydraulic system, movement depends on_____ furniture or utility items - Answer Fractional dimensions are used on objects such as _______ or ______ elimination - Answer If the cause of the problem is not immediately understood, the process of________is often the procedure of choice 3/16 - Answer When applying sealant to the sealing gland flanges, keep the sealant away from the inside edges of the flange by at least_______ inch Transducer - Answer A stroboscope is triggered by a_______ thread - Answer The pitch of threaded fasteners is measured with a ________gauge Surface cracks - Answer Liquid penetrant highlights flaws and reveals________ die - Answer A tool used to cut external threats on s bolt or rod is called a ______ special processes - Answer A bill of materials may include info on _______ and other reference information surface speed - Answer Engaged gears always have the same _____ general arrangement - Answer Elevation of equipment is usually found in the_____ Vibrations - Answer Inspect the pulleys, rollers, and idlers for unevenness or______ 15-20 degree angle - Answer When cutting thin steel with Oxyfuel fuel cutting equipment, hold the torch so that the tip is pointing in the direction the torch is traveling at a _____ angle Grease......... - Answer Labby seals work BEST with materials such as_____ Friction - Answer Lubrication is the application of any substance that reduces________ Driver coupling jig - Answer When the dial indicator is mounted on the complex reverse driven coupling jig , the indicator is registered on the____ In racks - Answer Pipe should be stored_____ Single deep groove radial - Answer The most common type of ball bearing is a _____ bearing split - Answer Couplings that are installed after the driver and driven shafts have been aligned and the equipment has been fastened into position are ________ couplings Factors - Answer When two or more numbers are multiplied to make another number thy ate called _______of the third number clockwise - Answer The continuous-reading dial indicator starts at zero and increases _________ Electronic filters - Answer Vibration within a specific narrow band range can be detected by _______ Teflon - Answer What type of o ring do you use with temperatures between-300 and 500? Rivet cutting - Answer The special cutting til for cutting off bolt heads and nuts is called a ______ tip pressure - Answer PCVs limit and regulate _______in the system Displacement - Answer The total distance the shaft travels from one peak to the other during one vibration cycle is the ______ Cup - Answer A positive-contact seal, generally used on cylinder pistons is the ______seal Brass plugs - Answer Equipment reference points are marked with_____ marring - Answer On a hydraulic press, use a piece of material softer than the work piece to keep from________ the work piece Exact bottom - Answer When setting up an angle iron jig, one indicator should be on the exact top of the MTBM, and the other indicator should be positioned at the ______ of the driven shaft A broken cam - Answer A pillow block barring failure that is caused by an undersized shaft is _______ Excessive leakage - Answer The most common symptom of packing failure is ________ filter - Answer The abbreviation FLT on a hydraulic drawing means _____ Lifting rough castings - Answer Chain slings are normally used for_________ Angle Dimensions - Answer Curved lines with arrowheads touching the extension lines are _________ Replacing damaged rollers - Answer Maintaining and repairing roller conveyors consists mainly of ________ Indicator sag - Answer When fabricating a jig, the millwright should minimize __________ Airfoil - Answer Air flows through the wheel with less turbulence in a __________ centrifugal fan


Document information

Uploaded on
September 9, 2023
Number of pages
12
Written in
2023/2024
Type
Exam (elaborations)
Contains
Questions & answers
$11.99

Wrong document? Swap it for free Within 14 days of purchase and before downloading, you can choose a different document. You can simply spend the amount again.
Written by students who passed
Immediately available after payment
Read online or as PDF

Seller avatar
Reputation scores are based on the amount of documents a seller has sold for a fee and the reviews they have received for those documents. There are three levels: Bronze, Silver and Gold. The better the reputation, the more your can rely on the quality of the sellers work.
Grademasters
3.8
(46)
Sold
118
Followers
69
Items
2591
Last sold
1 month ago




Why students choose Stuvia

Created by fellow students, verified by reviews

Quality you can trust: written by students who passed their tests and reviewed by others who've used these notes.

Didn't get what you expected? Choose another document

No worries! You can instantly pick a different document that better fits what you're looking for.

Pay as you like, start learning right away

No subscription, no commitments. Pay the way you're used to via credit card and download your PDF document instantly.

Student with book image

“Bought, downloaded, and aced it. It really can be that simple.”

Alisha Student

Working on your references?

Create accurate citations in APA, MLA and Harvard with our free citation generator.

Working on your references?

Frequently asked questions

Whoops! We can’t load your doc right now. Try again or contact support.