CYB-210 Project One
Computer Network
Modification.
, This brief will explain the steps that were taken to configure new devices and the network.
Screenshots are included for each step for better understanding. Completed the following:
• Add free guest wireless internet for the customers
• Install cameras that monitor the front desk and the waiting area.
• Reconfigure the current network to support the new hardware.
The needed hardware is already in the office, so the cameras and wireless router were
harvested from the equipment closet. To get the network ready for the new hardware, the
existing switch was reconfigured first. After selecting the switch and clicking on the CLI, a
command was entered (see Figure 1) to add and name the new VLAN for the wireless router’s
“Guest” network. The command was run again to add and name the new VLAN for the
camera’s video network (see Figure 2). Figure 3 is the VLAN table showing both VLAN 70 and
80 have been added and the existing VLAN 50 and 150 are still configured. Next the wireless
router was physically connected to the switch using a copper straight-through cable. It was
plugged into FastEthernet0/7 on the router and Ethernet 1 on the wireless router. The
FastEthernet0/7 port on the switch was assigned to VLAN 70 . This was done with the CLI on
the switch (see Figure 4). Next, the wireless router needed to be configured. On the LAN option
under the config tab of the router, the IP address was set to 192.168.70.10 (see Figure 5).
Verified that the IP configuration was set to DHCP on the internet option under the config tab of
the router (see Figure 6). Configuration was continued in the wireless section under the config
tab. The SSID was labeled “Guest”, Both authentication and encryption type set to disabled (see
figure 7). The router configuration was competed under the GUI tab. Verified that the internet
connection type was set to DHCP, the router IP address was 192.168.70.10, the start IP address
set to 192.168.70.101 and the maximum number of users to 70 (see Figure 8). The client lease
time is set at the default 1 day. This will be fine since the clients won’t use it for more than 4
hours.
Computer Network
Modification.
, This brief will explain the steps that were taken to configure new devices and the network.
Screenshots are included for each step for better understanding. Completed the following:
• Add free guest wireless internet for the customers
• Install cameras that monitor the front desk and the waiting area.
• Reconfigure the current network to support the new hardware.
The needed hardware is already in the office, so the cameras and wireless router were
harvested from the equipment closet. To get the network ready for the new hardware, the
existing switch was reconfigured first. After selecting the switch and clicking on the CLI, a
command was entered (see Figure 1) to add and name the new VLAN for the wireless router’s
“Guest” network. The command was run again to add and name the new VLAN for the
camera’s video network (see Figure 2). Figure 3 is the VLAN table showing both VLAN 70 and
80 have been added and the existing VLAN 50 and 150 are still configured. Next the wireless
router was physically connected to the switch using a copper straight-through cable. It was
plugged into FastEthernet0/7 on the router and Ethernet 1 on the wireless router. The
FastEthernet0/7 port on the switch was assigned to VLAN 70 . This was done with the CLI on
the switch (see Figure 4). Next, the wireless router needed to be configured. On the LAN option
under the config tab of the router, the IP address was set to 192.168.70.10 (see Figure 5).
Verified that the IP configuration was set to DHCP on the internet option under the config tab of
the router (see Figure 6). Configuration was continued in the wireless section under the config
tab. The SSID was labeled “Guest”, Both authentication and encryption type set to disabled (see
figure 7). The router configuration was competed under the GUI tab. Verified that the internet
connection type was set to DHCP, the router IP address was 192.168.70.10, the start IP address
set to 192.168.70.101 and the maximum number of users to 70 (see Figure 8). The client lease
time is set at the default 1 day. This will be fine since the clients won’t use it for more than 4
hours.