• Wrong document? Swap it for free
  • Written by students who passed
  • Immediately available after payment
  • Read online or as PDF
Sell
Where do you study
Your language
Document preview thumbnail
Preview 3 out of 29 pages
Exam (elaborations)

Study Material for API 1104 CWI 046 - Practice-Ready Answer Guide

Document preview thumbnail
Preview 3 out of 29 pages

Study Material for API 1104 CWI 046 - Practice-Ready Answer Guide In which of the following ways are fluxes for SAW classified when classified according to the manner in which they modify the composition of the weld metal? a. Oxidizing or reducing b. Fused or agglomerated c. Granular or powdered d. Neutral, active or alloy e. Covered or self-shielded - answer - b. Fused or agglomerated What does the 'R' indicate in the wire ER70S-3 AWS filler metal classification? a. Rolled in a spool b. May be used as a filler rod c. Rust resistant d. Rosin core e. Reverse Polarity - answer - b. May be used as a filler rod Which of the following is/are false regarding good quality records? a. All records should be prepared by the welding inspector b. They record as much detail as necessary c. They include explanation of repairs d. They state how well the work stayed with prescribed tolerances. e. All of the above - answer - a. All records should be prepared by the welding inspector Porosity in the weld bead can result from which of the following? a. Contaminated electrodes b. Contaminated shielding gas c. Moisture pickup d. Arc voltage too high e. All of the above - answer - e. All of the above Overexposure to X-rays or gamma rays may cause damage to human ______________________. a. Sexual organs b. Blood tissue c. Skin d. Internal organs e. All of the above - answer - e. All of the above Which of the following conditions will affect the rate and extent to which a liquid penetrant will enter cracks, fissures and other small openings? a. The hardness of the specimen being tested b. The surface condition of the specimen being tested c. The color of the penetrant d. The conductivity of the specimen being tested e. The magnetic field residual in the specimen - answer - b. The surface condition of the specimen being tested Which of the following activities are encountered in welding inspection? a. Selection and examination of production test samples b. Verification of approved welding procedures c. Verification of personnel qualifications d. Only (b) and (c) e. Only (a), (b) and (c) - answer - e. Only (a), (b) and (c) a. Selection and examination of production test samples b. Verification of approved welding procedures c. Verification of personnel qualifications Destructive tests of welds are designed to ___________________. a. Determine the mechanical properties(i.e. tensile strength, ductility and toughness) b.Determine the modulus of elasticity of a weld metal c. Calculate the percentage of reduction in area for an all-weld-metal specimen d. Determine the soundness of weld metal e. All of the above - answer - e. All of the above In GMAW, shielding gas selection will not have a pronounced effect on which of following: a. Electrode extension b. Undercutting tendency c. Mode of metal transfer d. Penetration e. Arc characteristics - answer - a. Electrode extension Which of the following FCAW process variation is most suitable for windy field conditions? a. Self-shielded b. Bare wire c. Metal core d. Gas-shielded e. Autogenously - answer - a. Self-shielded Which of the following statements is correct regarding magnetic particle testing? a. It is sensitive enough to readily able to detect subsurface discontinuities b. It can be performed on all type of material, ferrous and non-ferrous c. Subsurface discontinuities are easily seen and interpreted with this method d. Subsurface discontinuities near the surface may be observed, but they may not be clearly defined e. None of the above - answer - d. Subsurface discontinuities near the surface may be observed, but they may not be clearly defined Which of the following is a cast iron electrode to AWS A5.15, Specification for Welding Electrodes and Rods for Cast Iron? a. ENiFe-CI-A b. EWC-30/40 c. E8018-C1 d. ECuAL-A2 e. ENi-Mo - answer - a. ENiFe-CI-A Which of the following is a disadvantage of some manual brazing processes in comparison to the automated ones? a. It cannot be


Document information

Uploaded on
November 19, 2026
Number of pages
29
Written in
2026/2027
Type
Exam (elaborations)
Contains
Questions & answers
$12.99

Wrong document? Swap it for free Within 14 days of purchase and before downloading, you can choose a different document. You can simply spend the amount again.
Written by students who passed
Immediately available after payment
Read online or as PDF

Seller avatar
Reputation scores are based on the amount of documents a seller has sold for a fee and the reviews they have received for those documents. There are three levels: Bronze, Silver and Gold. The better the reputation, the more your can rely on the quality of the sellers work.
SARAHnkalu
4.6
(7)
Sold
48
Followers
0
Items
7562
Last sold
1 week ago



Why students choose Stuvia

Created by fellow students, verified by reviews

Quality you can trust: written by students who passed their tests and reviewed by others who've used these notes.

Didn't get what you expected? Choose another document

No worries! You can instantly pick a different document that better fits what you're looking for.

Pay as you like, start learning right away

No subscription, no commitments. Pay the way you're used to via credit card and download your PDF document instantly.

Student with book image

“Bought, downloaded, and aced it. It really can be that simple.”

Alisha Student

Working on your references?

Create accurate citations in APA, MLA and Harvard with our free citation generator.

Working on your references?

Frequently asked questions

Whoops! We can’t load your doc right now. Try again or contact support.