ABOMS Oral & Maxillofacial Surgery
Comprehensive Resource To Help You Ace 2026-2027 Exams
Includes Frequently Tested Questions With
Elaborated 100% Correct Complete Solutions
Guaranteed Pass First Attempt!! Current Update!!
1. Which teeth are located in the center front of the mouth?
A. bicuspids
B. cuspids
C. incisors
D. molars - CORRECT ANSWER incisors
2. Which procedure is performed for removal of impacted wisdom teeth?
A. enucleation
B. extraction
C. mandibulectomy
D. odontectomy - CORRECT ANSWER odontectomy
3. Coral would be classified as what type of graft material?
A. autograft
B. homograft
C. synthetic
D. xenograft - CORRECT ANSWER xenograft
4. All of the following are configurations of fixation plates for maxillofacial
fracture reduction?
, A. H
B. L
C. W
D. Y - CORRECT ANSWER W
5. Strands of wire used to attach arch bars to the upper and lower jaw should
be pre-stretched and cut to which length?
A. 5 cm
B. 10 cm
C. 15 cm
D. 20 cm - CORRECT ANSWER 10 cm
6. Which of the following statements regarding arch bars is CORRECT?
A. They are thin, malleable bars with hooks facing up for maxilla and
down for mandible
B. They are thin, malleable bars with hooks facing down for maxilla and
up for mandible
C. They are thick, rigid, semicircle bars with hooks facing up for maxilla
and down for mandible
D. They are thick, rigid, semicircle bars with hooks facing down for
maxilla and up for mandible - CORRECT ANSWER They are thin,
malleable bars with hooks facing up for maxilla and down for
mandible
7. Which sequence of steps for plate fixation is CORRECT?
A. Drill all holes, place plate, tap, measure with depth gauge, and insert
screws
B. Drill all holes, place plate, measure with depth gauge, tap, and insert
screws
, C. Place plate, drill one hole at a time, tap, measure with depth gauge,
insert screw, and repeat steps for remaining holes
D. Place plate, drill one hole at a time, measure with depth gauge, tap,
insert screw, and repeat steps for remaining holes - CORRECT
ANSWER Place plate, drill one hole at a time, measure with depth
gauge, tap, insert screw, and repeat steps for remaining holes.
8. Tapping of bone is done in fixation procedures to reduce:
A. number of screws needed
B. torque pressure on screws
C. size of fixation plate used
D. need to strip periosteum first - CORRECT ANSWER torque pressure on
screws
9. How many craniofacial bones make up the orbit?
A. three
B. five
C. seven
D. nine - CORRECT ANSWER seven
10.What is the term that describes the side of teeth closest to the cheek?
A. alveolar
B. buccal
C. labial
D. lingual - CORRECT ANSWER buccal
11.Which of the following is NOT one of the three regions of a tooth?
A. crown
B. neck
Comprehensive Resource To Help You Ace 2026-2027 Exams
Includes Frequently Tested Questions With
Elaborated 100% Correct Complete Solutions
Guaranteed Pass First Attempt!! Current Update!!
1. Which teeth are located in the center front of the mouth?
A. bicuspids
B. cuspids
C. incisors
D. molars - CORRECT ANSWER incisors
2. Which procedure is performed for removal of impacted wisdom teeth?
A. enucleation
B. extraction
C. mandibulectomy
D. odontectomy - CORRECT ANSWER odontectomy
3. Coral would be classified as what type of graft material?
A. autograft
B. homograft
C. synthetic
D. xenograft - CORRECT ANSWER xenograft
4. All of the following are configurations of fixation plates for maxillofacial
fracture reduction?
, A. H
B. L
C. W
D. Y - CORRECT ANSWER W
5. Strands of wire used to attach arch bars to the upper and lower jaw should
be pre-stretched and cut to which length?
A. 5 cm
B. 10 cm
C. 15 cm
D. 20 cm - CORRECT ANSWER 10 cm
6. Which of the following statements regarding arch bars is CORRECT?
A. They are thin, malleable bars with hooks facing up for maxilla and
down for mandible
B. They are thin, malleable bars with hooks facing down for maxilla and
up for mandible
C. They are thick, rigid, semicircle bars with hooks facing up for maxilla
and down for mandible
D. They are thick, rigid, semicircle bars with hooks facing down for
maxilla and up for mandible - CORRECT ANSWER They are thin,
malleable bars with hooks facing up for maxilla and down for
mandible
7. Which sequence of steps for plate fixation is CORRECT?
A. Drill all holes, place plate, tap, measure with depth gauge, and insert
screws
B. Drill all holes, place plate, measure with depth gauge, tap, and insert
screws
, C. Place plate, drill one hole at a time, tap, measure with depth gauge,
insert screw, and repeat steps for remaining holes
D. Place plate, drill one hole at a time, measure with depth gauge, tap,
insert screw, and repeat steps for remaining holes - CORRECT
ANSWER Place plate, drill one hole at a time, measure with depth
gauge, tap, insert screw, and repeat steps for remaining holes.
8. Tapping of bone is done in fixation procedures to reduce:
A. number of screws needed
B. torque pressure on screws
C. size of fixation plate used
D. need to strip periosteum first - CORRECT ANSWER torque pressure on
screws
9. How many craniofacial bones make up the orbit?
A. three
B. five
C. seven
D. nine - CORRECT ANSWER seven
10.What is the term that describes the side of teeth closest to the cheek?
A. alveolar
B. buccal
C. labial
D. lingual - CORRECT ANSWER buccal
11.Which of the following is NOT one of the three regions of a tooth?
A. crown
B. neck
