• Wrong document? Swap it for free
  • Written by students who passed
  • Immediately available after payment
  • Read online or as PDF
Sell
Where do you study
Your language
Document preview thumbnail
Preview 4 out of 37 pages
Exam (elaborations)

Exam_Elaborations_Irc_Building_Code_Final_Paper_2026_Test_Paper.pdf

Document preview thumbnail
Preview 4 out of 37 pages

Exam_Elaborations_Irc_Building_Code_Final_Paper_2026_Test_P

Content preview

EXAM ELABORATIONS IRC
BUILDING UPDATED QUESTIONS
WITH CORRECT ANSWERS

◉ When the header joist span does not exceed ____ feet, the header
joist may be a single member the same size as the floor joist.
Answer: 4 ft.
(When the header joist span exceeds 4 feet the trimmer joists and
header joists shall be doubled)


R502.10 Framing of openings


◉ In combustible construction, where there is usable space both
above and below a floor/ceiling assembly, draft stops shall be
installed so that the area of the concealed space does not exceed ____
square feet. Answer: 1000 sq. ft.
(Draft-stopping shall divide the concealed space into approximately
equal areas.


R302.12 Draft-stopping


◉ The provisions of Section R505 Steel Floor Framing shall control
the construction of cold-formed steel floor framing for building not

,greater than ____ feet in length perpendicular to the joist span.
Answer: 60 ft.
(Read this section for more applicability limits).


R505.1.1 Applicability limits


◉ Flanges and lips of load-bearing cold-formed steel floor framing
members shall not be cut or ____. Answer: Notched


R505.3.5


◉ In cold-formed steel framing, floor cantilevers for the top floor of
a two- or three-story building or the first floor of a one-story
buidling shall not exceed ____. Answer: 24 in.


R505.3.6 Floor cantilevers


◉ Concrete slab-on-ground floors shall be a minimum of ____ inches
thick. Answer: 3.5 in.


R506.1 General

,◉ The connection between a deck ledger and a 2-inch nominal
lumber band joist shall be constructed with ____-inch lag screws or
bolts with washers. Answer: 1/2 in.
(In accordance with Table R507.2. See figures R507.2.1(1) and
R507.2.1(2)


R507.2 Deck ledger connection to band joist.


◉ For wood stud walls, end joints in top plates shall be offset at least
____ inches. Answer: 24 in.


R602.3.2 Top plate


◉ When joists, trusses or rafters are spaced more than 16 inches on
center and the bearing studs below are spaced 24 inches on center,
such members shall bear within ____ inches of the studs beneath.
Answer: 5 in.
(Read 3 exceptions in this section)


R602.3.3 Bearing studs


◉ Any wood stud in an exterior wall or bearing partition may be cut
or notched to a depth not exceeding ____ percent of its width.
Answer: 25%

, R602.6 Drilling and notching studs #1


◉ Wood studs in non bearing partitions may be notched to a depth
not exceeding ____ percent of a single stud width. Answer: 40%


R602.6 Drilling and notching studs #1


◉ Exterior wood frame walls shall be offset not more than ___ feet
from the designated braced wall line location. Answer: 4 ft.
(See figure R602.10.1.1)


R602.10.1.2 Offsets along a braced wall line.


◉ Braced wall lines greater than 16 feet shall have a minimum of ____
braced wall panels. Answer: two


R602.10.2.3 Minimum number of braced wall panels.


◉ Wall bracing Method PFG (Portal frame at garage door openings)
is limited to walls supporting ____ ____ and a _____. Answer: One story
Roof
(This method is also limited to Seismic Design Categories A, B and C.

Document information

Uploaded on
October 15, 2026
Number of pages
37
Written in
2026/2027
Type
Exam (elaborations)
Contains
Questions & answers
$16.49

Wrong document? Swap it for free Within 14 days of purchase and before downloading, you can choose a different document. You can simply spend the amount again.
Written by students who passed
Immediately available after payment
Read online or as PDF

Sold
4
Followers
0
Items
8342
Last sold
1 week ago



Why students choose Stuvia

Created by fellow students, verified by reviews

Quality you can trust: written by students who passed their tests and reviewed by others who've used these notes.

Didn't get what you expected? Choose another document

No worries! You can instantly pick a different document that better fits what you're looking for.

Pay as you like, start learning right away

No subscription, no commitments. Pay the way you're used to via credit card and download your PDF document instantly.

Student with book image

“Bought, downloaded, and aced it. It really can be that simple.”

Alisha Student

Working on your references?

Create accurate citations in APA, MLA and Harvard with our free citation generator.

Working on your references?

Frequently asked questions