Manual Transmissions and Drivetrains LATEST
ACTUAL EXAM WITH VERIFIED QUESTIONS & CORRECT
ANSWERS
Question 1.
A FWD car has a clicking noise when turning. Technician A says a worn inner CV joint may be the cause.
Technician B says a worn outer CV joint may be the cause. Who is correct?
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
ANSWER
b. Technician B
Question 2.
Technician A says out-of-phase U-joints can cause a vibration. Technician B says incorrect driveline
angles can cause a vibration. Who is correct?
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor
ANSWER
c. Both A and B
Question 3.
Which type of rear axle gearsets do not need to be indexed?
ANSWER
Hunting Gearset
,Question 4.
Technician A says most rear differentials can use 80 or 90 weight gear lubricant. Technician B says
limited-slip differentials require special lubricants. Who is correct?
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
ANSWER
b. Technician B
Question 5.
In front-wheel drivetrains, the CV joint nearer the transaxle is the ___.
a. inner joint
b. inboard joint
c. outboard joint
d. Both A and B
ANSWER
d. Both A and B
Question 6.
A CV joint that is capable of in-and-out movement is a ___.
a. plunge joint
b. fixed joint
c. inboard joint
d. Both A and C
ANSWER
a. plunge joint
Question 7.
The double-offset CV joint is typically used in applications that require ___.
a. higher operating angles and greater plunge depth b. lower operating angles and lower plunge
depth
c. higher operating angles and lower plunge depth d. lower operating angles and greater plunge
depth
ANSWER
a. higher operating angles and greater plunge depth
,Question 8.
Which type of joint has a flatter design than any other?
a. Double-offset
b. Disc
c. Cross groove
d. Fixed tripod
ANSWER
c. Cross groove
Question 9.
Which of these is the best way to determine which CV joint is faulty?
a. Squeeze test
b. Runout test
c. Visual inspection
d. Road test
ANSWER
d. Road test
Question 10.
The single Cardan/Spicer universal joint is also known as the ___.
a. cross joint
b. four-point joint
c. Both A and B
d. Neither A nor B
ANSWER
c. Both A and B
Question 11.
The drive shaft component that provides a means of connecting two or more shafts together is the ___.
a. pinion flange
b. U-joint
c. yoke
d. biscuit
ANSWER
c. yoke
, Question 12.
Large cars with long drive shafts often use a double-U-joint arrangement called a ___.
a. Spicer style U-joint
b. constant velocity U-joint
c. Cleveland style U-joint
d. none of the above
ANSWER
b. constant velocity U-joint
Question 13.
Which type of driving axle supports the weight of the vehicle?
a. Semifloating
b. Three-quarter floating
c. Full-floating
d. None of the above
ANSWER
a. Semifloating
Question 14.
Which of the following describes the double-Cardan universal joint?
a. It is most often installed in front-engine rear-wheel-drive luxury automobiles.
b. It is classified as a constant velocity U-joint.
c. A centering ball socket is inside the coupling yoke between the two universal joints.
d. All of the above.
ANSWER
d. All of the above.
Question 15.
Technician A says that a gear tooth pattern identifies excessive ring gear runout. Technician B says that
gear patterns are not accurate if there is excessive ring gear runout. Who is correct?
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
ANSWER
b. Technician B
ACTUAL EXAM WITH VERIFIED QUESTIONS & CORRECT
ANSWERS
Question 1.
A FWD car has a clicking noise when turning. Technician A says a worn inner CV joint may be the cause.
Technician B says a worn outer CV joint may be the cause. Who is correct?
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
ANSWER
b. Technician B
Question 2.
Technician A says out-of-phase U-joints can cause a vibration. Technician B says incorrect driveline
angles can cause a vibration. Who is correct?
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor
ANSWER
c. Both A and B
Question 3.
Which type of rear axle gearsets do not need to be indexed?
ANSWER
Hunting Gearset
,Question 4.
Technician A says most rear differentials can use 80 or 90 weight gear lubricant. Technician B says
limited-slip differentials require special lubricants. Who is correct?
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
ANSWER
b. Technician B
Question 5.
In front-wheel drivetrains, the CV joint nearer the transaxle is the ___.
a. inner joint
b. inboard joint
c. outboard joint
d. Both A and B
ANSWER
d. Both A and B
Question 6.
A CV joint that is capable of in-and-out movement is a ___.
a. plunge joint
b. fixed joint
c. inboard joint
d. Both A and C
ANSWER
a. plunge joint
Question 7.
The double-offset CV joint is typically used in applications that require ___.
a. higher operating angles and greater plunge depth b. lower operating angles and lower plunge
depth
c. higher operating angles and lower plunge depth d. lower operating angles and greater plunge
depth
ANSWER
a. higher operating angles and greater plunge depth
,Question 8.
Which type of joint has a flatter design than any other?
a. Double-offset
b. Disc
c. Cross groove
d. Fixed tripod
ANSWER
c. Cross groove
Question 9.
Which of these is the best way to determine which CV joint is faulty?
a. Squeeze test
b. Runout test
c. Visual inspection
d. Road test
ANSWER
d. Road test
Question 10.
The single Cardan/Spicer universal joint is also known as the ___.
a. cross joint
b. four-point joint
c. Both A and B
d. Neither A nor B
ANSWER
c. Both A and B
Question 11.
The drive shaft component that provides a means of connecting two or more shafts together is the ___.
a. pinion flange
b. U-joint
c. yoke
d. biscuit
ANSWER
c. yoke
, Question 12.
Large cars with long drive shafts often use a double-U-joint arrangement called a ___.
a. Spicer style U-joint
b. constant velocity U-joint
c. Cleveland style U-joint
d. none of the above
ANSWER
b. constant velocity U-joint
Question 13.
Which type of driving axle supports the weight of the vehicle?
a. Semifloating
b. Three-quarter floating
c. Full-floating
d. None of the above
ANSWER
a. Semifloating
Question 14.
Which of the following describes the double-Cardan universal joint?
a. It is most often installed in front-engine rear-wheel-drive luxury automobiles.
b. It is classified as a constant velocity U-joint.
c. A centering ball socket is inside the coupling yoke between the two universal joints.
d. All of the above.
ANSWER
d. All of the above.
Question 15.
Technician A says that a gear tooth pattern identifies excessive ring gear runout. Technician B says that
gear patterns are not accurate if there is excessive ring gear runout. Who is correct?
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
ANSWER
b. Technician B
