SCTE BPI CORE 2027 ANSWERS AND QUESTIONS SET
A+
✔✔To establish a good electrical bond, meter pan bonding connectors and bar clamps,
- ✔✔employ small, sharply pointed bolts to penetrate the paint of the cabinet Fram to
reach bare metal
✔✔To verify that an interior metal water piping system is bonded to the utility power
ground system - ✔✔visually inspect the exterior and interior metal water piping system
or measure the resistance between the water pipe and any grounded utility power
equipment or conduit
✔✔when installing cable at a mobile home, - ✔✔If your electrical power service
equipment is not more than 30 ft away bond to the electrical power grounding conductor
grounding electrode grounded metallic raceways or meter body pans
✔✔A ground block - ✔✔Is basically an F 81 connector mounted to a metal block that
provides a bonding wire attachment screw
✔✔According to the NEC< bonding wire size shall be - ✔✔Not smaller the number 14
gauge carrying capacity approximately equal to that of the outer conductor the coaxial
drop cable
✔✔The signals coming from the customer premise to the fiber node and ultimately to
the hub and or headend are called - ✔✔upstream
✔✔cable loss is expressed in - ✔✔dB
✔✔4 to 1 ladder rule - ✔✔For every four feet of ladder height the base of the ladder
should be one horizontal foot out from the top support point of the ladder
✔✔3 primary pole inspection methods - ✔✔Visual inspection sound test prod test
, ✔✔The analog television standard established in 1940s by the United States FCC is
called - ✔✔NTSC
✔✔The signals going from into the fiber node and ultimately to the customers premises
are called - ✔✔downstream
✔✔best definition for partnering with the customer - ✔✔By working with the customer
toward the same goal
✔✔It is important to project a positive company image while off the job because -
✔✔You represent your company / / you are a Goodwill Ambassador
✔✔What is the most common inside wire used today for telephone and data circuits -
✔✔Cat 5(5e)
✔✔when routing drop cable to an exterior cable entry hole - ✔✔Route the cable behind
any obstacles along the proposed path to the entry hole
✔✔one advantage of. prewired installation is - ✔✔All Broadband drop cables in the
home join together at a common location
✔✔When routing drop cables through an exterior entry hole to the wall plate location -
✔✔Protect the drop cable from damage and help seal the wall service by using a feed
through bushing
✔✔When routing drop cable through a crawl space - ✔✔Pulling up drop cable through
the floor to reach the customer premises equipment
✔✔When routing drop Cable in an unfinished basement - ✔✔Attach the drop cable to
the side of the floor joist and not to the bottom
✔✔When routing drop cable through a finished basement - ✔✔Locate the exterior entry
hole as close as possible to the customer premises equipment / devices
✔✔When routing drop cable within an interior wall from an attic - ✔✔Lower the fish
chain into the wall fish hole and help guide the drop cable into the hole until the chain
contacts the wall bottom plate
✔✔When routing drop cable with an interior wall up from an unfinished basement or
crawlspace - ✔✔Push the fish wire attached to drop cable up through the wall so it can
be hooked with another fish wire and pulled through exit hole
A+
✔✔To establish a good electrical bond, meter pan bonding connectors and bar clamps,
- ✔✔employ small, sharply pointed bolts to penetrate the paint of the cabinet Fram to
reach bare metal
✔✔To verify that an interior metal water piping system is bonded to the utility power
ground system - ✔✔visually inspect the exterior and interior metal water piping system
or measure the resistance between the water pipe and any grounded utility power
equipment or conduit
✔✔when installing cable at a mobile home, - ✔✔If your electrical power service
equipment is not more than 30 ft away bond to the electrical power grounding conductor
grounding electrode grounded metallic raceways or meter body pans
✔✔A ground block - ✔✔Is basically an F 81 connector mounted to a metal block that
provides a bonding wire attachment screw
✔✔According to the NEC< bonding wire size shall be - ✔✔Not smaller the number 14
gauge carrying capacity approximately equal to that of the outer conductor the coaxial
drop cable
✔✔The signals coming from the customer premise to the fiber node and ultimately to
the hub and or headend are called - ✔✔upstream
✔✔cable loss is expressed in - ✔✔dB
✔✔4 to 1 ladder rule - ✔✔For every four feet of ladder height the base of the ladder
should be one horizontal foot out from the top support point of the ladder
✔✔3 primary pole inspection methods - ✔✔Visual inspection sound test prod test
, ✔✔The analog television standard established in 1940s by the United States FCC is
called - ✔✔NTSC
✔✔The signals going from into the fiber node and ultimately to the customers premises
are called - ✔✔downstream
✔✔best definition for partnering with the customer - ✔✔By working with the customer
toward the same goal
✔✔It is important to project a positive company image while off the job because -
✔✔You represent your company / / you are a Goodwill Ambassador
✔✔What is the most common inside wire used today for telephone and data circuits -
✔✔Cat 5(5e)
✔✔when routing drop cable to an exterior cable entry hole - ✔✔Route the cable behind
any obstacles along the proposed path to the entry hole
✔✔one advantage of. prewired installation is - ✔✔All Broadband drop cables in the
home join together at a common location
✔✔When routing drop cables through an exterior entry hole to the wall plate location -
✔✔Protect the drop cable from damage and help seal the wall service by using a feed
through bushing
✔✔When routing drop cable through a crawl space - ✔✔Pulling up drop cable through
the floor to reach the customer premises equipment
✔✔When routing drop Cable in an unfinished basement - ✔✔Attach the drop cable to
the side of the floor joist and not to the bottom
✔✔When routing drop cable through a finished basement - ✔✔Locate the exterior entry
hole as close as possible to the customer premises equipment / devices
✔✔When routing drop cable within an interior wall from an attic - ✔✔Lower the fish
chain into the wall fish hole and help guide the drop cable into the hole until the chain
contacts the wall bottom plate
✔✔When routing drop cable with an interior wall up from an unfinished basement or
crawlspace - ✔✔Push the fish wire attached to drop cable up through the wall so it can
be hooked with another fish wire and pulled through exit hole
