NACE CIP LEVEL 2 LATEST ACTUAL EXAM WITH VERIFIED
QUESTIONS & CORRECT ANSWERS
Question 1.
Describe what the
characteristics of a
heavy flash rusted
surface are. 7-5
Correct Answer: Rust that is loosely adherent, easily comes of, & leaves
significant marks on a cloth that is lightly wiped over the surface.
Question 2.
Describe what the
characteristics of
a moderate flash
rusted surface are.
7-5
Correct Answer: Rust that is reasonably well adherent and leaves light marks on
a cloth that is lightly wiped over the surface.
Question 3.
Describe what the
characteristics of a
light flash rusted
surface are. 7-5
Correct Answer: Rust that is tightly adherent & not easily removed by lightly
wiping with a cloth.
Question 4.
At what psig is
low-pressure clean-
ing preformed at?
7-2
Correct Answer: below 5000 psig
Question 5.
At what psig
is high-pressure
cleaning preformed
at? 7-2
Correct Answer: 5000-10,000 psig
, Question 6.
At what psig
is high-pressure
waterjetting pre-
formed at? 7-2
Correct Answer: 10,000-30,000 psig
Question 7.
At what psig
is ultrahigh-pres-
sure waterjetting
preformed at 7-2
Correct Answer: above 30,000 psig
Question 8.
What does water-
jetting not create?
7-1
Correct Answer: An anchor profile
Question 9.
In the marine in-
dustry, waterjetting
is widely used for
what purposes? 7-1
Correct Answer: Removal of marine growth, depleted antifouling coatings and
surface preparation of tank/hold interiors
Question 10.
What industries is
waterjetting partic-
ularly well suited
for? 7-1
Correct Answer: Marine, process and utility industries.
Question 11.
What standard
specifies the
amount of non vis-
ible contaminants
that are allowed to
QUESTIONS & CORRECT ANSWERS
Question 1.
Describe what the
characteristics of a
heavy flash rusted
surface are. 7-5
Correct Answer: Rust that is loosely adherent, easily comes of, & leaves
significant marks on a cloth that is lightly wiped over the surface.
Question 2.
Describe what the
characteristics of
a moderate flash
rusted surface are.
7-5
Correct Answer: Rust that is reasonably well adherent and leaves light marks on
a cloth that is lightly wiped over the surface.
Question 3.
Describe what the
characteristics of a
light flash rusted
surface are. 7-5
Correct Answer: Rust that is tightly adherent & not easily removed by lightly
wiping with a cloth.
Question 4.
At what psig is
low-pressure clean-
ing preformed at?
7-2
Correct Answer: below 5000 psig
Question 5.
At what psig
is high-pressure
cleaning preformed
at? 7-2
Correct Answer: 5000-10,000 psig
, Question 6.
At what psig
is high-pressure
waterjetting pre-
formed at? 7-2
Correct Answer: 10,000-30,000 psig
Question 7.
At what psig
is ultrahigh-pres-
sure waterjetting
preformed at 7-2
Correct Answer: above 30,000 psig
Question 8.
What does water-
jetting not create?
7-1
Correct Answer: An anchor profile
Question 9.
In the marine in-
dustry, waterjetting
is widely used for
what purposes? 7-1
Correct Answer: Removal of marine growth, depleted antifouling coatings and
surface preparation of tank/hold interiors
Question 10.
What industries is
waterjetting partic-
ularly well suited
for? 7-1
Correct Answer: Marine, process and utility industries.
Question 11.
What standard
specifies the
amount of non vis-
ible contaminants
that are allowed to
