ACI Concrete Field-Testing Technician Grade I Certification
Exam Actual Exam 2026/2027 | Complete Exam-Style
Questions with Detailed Rationales | 100% Verified — Pass
Guaranteed – A+ Graded
Concrete Fundamentals and Test Preparation
Q1: According to ACI guidelines, what is the primary role of a certified Concrete Field-
Testing Technician Grade I?
A. To design the concrete mix proportions for the specific project.
B. To approve or reject the concrete delivery on behalf of the project engineer.
C. To perform, record, and report standard field tests on fresh concrete. [CORRECT]
D. To calculate the compressive strength of hardened concrete cylinders.
Correct Answer: C
Rationale: The best answer is to perform, record, and report standard field tests on fresh
concrete. This matches the principle that the Grade I technician’s scope is strictly limited to
observing, sampling, and testing fresh concrete, not making engineering judgments or mix
designs.
Q2: You are tasked with obtaining a composite sample from a stationary paved mixer. What
is the correct procedure to ensure the sample is representative?
A. Take a single, large scoop from the very center of the discharged pile.
B. Collect portions from at least three different locations of the discharge pile and mix them
thoroughly. [CORRECT]
C. Sample only the first portion of the batch to capture the initial mix consistency.
D. Wait until the entire batch is discharged and sample from the outer edges of the pile.
Correct Answer: C
Rationale: This choice is correct because ASTM C172 requires combining portions from at
least three different locations to account for any segregation or variation during discharge.
This aligns with the principle that a composite sample provides a true, averaged
representation of the entire batch.
Q3: What is the maximum allowable time between adding water to the concrete mix and
completing the slump, air content, and temperature tests?
A. 5 minutes [CORRECT]
B. 10 minutes
C. 15 minutes
D. 30 minutes
Correct Answer: C
Rationale: The best answer is 5 minutes because concrete properties begin to change
rapidly due to hydration and evaporation once mixing begins. This matches the principle
that timely testing is critical to capturing the true, as-delivered state of the fresh concrete.
, Q4: A concrete truck arrives at the job site, but due to a delayed pump setup, it sits for 20
minutes before you can begin sampling. What should you do?
A. Proceed with the tests but add a note that the concrete was delayed.
B. Add a small amount of water to restore the original slump before testing.
C. Note the elapsed time and recognize that the test results may not reflect the initial
discharge conditions. [CORRECT]
D. Reject the load immediately without performing any field tests.
Correct Answer: C
Rationale: This choice is correct because the technician must document the actual
conditions observed, including delays that affect the concrete's properties. This aligns with
the principle that field testers report factual data, leaving the decision to accept or reject
the material to the specifying authority.
Q5: You review a batch ticket indicating a target air content of 5.0%. Your field test using the
volumetric method yields a result of 7.2%. What is the most appropriate initial action?
A. Reject the load immediately and send the truck back to the plant.
B. Add more water to the mix to bring the air content down to the target.
C. Document the 7.2% result and notify the supervising engineer or inspector. [CORRECT]
D. Average the ticket value and your field value to report 6.1%.
Correct Answer: C
Rationale: The best answer is to document the 7.2% result and notify the supervising
engineer or inspector. This aligns with the principle that field testers do not have the
authority to reject materials, but must provide the factual data for the engineer to make
that decision.
Q6: What is the required accuracy range for a temperature-measuring device used to test
freshly mixed concrete according to ASTM C1064?
A. ±0.5°F (±0.3°C)
B. ±1.0°F (±0.5°C) [CORRECT]
C. ±2.0°F (±1.0°C)
D. ±5.0°F (±3.0°C)
Correct Answer: C
Rationale: This choice is correct because ASTM C1064 specifies that the temperature-
measuring device must be accurate to within ±1.0°F (±0.5°C) to ensure reliable monitoring
of concrete placement conditions. This matches the principle that precise temperature data
is essential for evaluating compliance with project specifications.
Q7: Before performing a slump test, how should the inside of the slump cone and the base
plate be prepared?
A. They should be coated with a thin layer of form release oil.
B. They should be completely dry to prevent diluting the concrete sample.
C. They should be dampened with water, leaving no standing water. [CORRECT]
D. They should be heated to match the ambient air temperature.
Correct Answer: C
Rationale: The best answer is that they should be dampened with water, leaving no standing
water. This aligns with the principle that a damp surface prevents the dry metal from
Exam Actual Exam 2026/2027 | Complete Exam-Style
Questions with Detailed Rationales | 100% Verified — Pass
Guaranteed – A+ Graded
Concrete Fundamentals and Test Preparation
Q1: According to ACI guidelines, what is the primary role of a certified Concrete Field-
Testing Technician Grade I?
A. To design the concrete mix proportions for the specific project.
B. To approve or reject the concrete delivery on behalf of the project engineer.
C. To perform, record, and report standard field tests on fresh concrete. [CORRECT]
D. To calculate the compressive strength of hardened concrete cylinders.
Correct Answer: C
Rationale: The best answer is to perform, record, and report standard field tests on fresh
concrete. This matches the principle that the Grade I technician’s scope is strictly limited to
observing, sampling, and testing fresh concrete, not making engineering judgments or mix
designs.
Q2: You are tasked with obtaining a composite sample from a stationary paved mixer. What
is the correct procedure to ensure the sample is representative?
A. Take a single, large scoop from the very center of the discharged pile.
B. Collect portions from at least three different locations of the discharge pile and mix them
thoroughly. [CORRECT]
C. Sample only the first portion of the batch to capture the initial mix consistency.
D. Wait until the entire batch is discharged and sample from the outer edges of the pile.
Correct Answer: C
Rationale: This choice is correct because ASTM C172 requires combining portions from at
least three different locations to account for any segregation or variation during discharge.
This aligns with the principle that a composite sample provides a true, averaged
representation of the entire batch.
Q3: What is the maximum allowable time between adding water to the concrete mix and
completing the slump, air content, and temperature tests?
A. 5 minutes [CORRECT]
B. 10 minutes
C. 15 minutes
D. 30 minutes
Correct Answer: C
Rationale: The best answer is 5 minutes because concrete properties begin to change
rapidly due to hydration and evaporation once mixing begins. This matches the principle
that timely testing is critical to capturing the true, as-delivered state of the fresh concrete.
, Q4: A concrete truck arrives at the job site, but due to a delayed pump setup, it sits for 20
minutes before you can begin sampling. What should you do?
A. Proceed with the tests but add a note that the concrete was delayed.
B. Add a small amount of water to restore the original slump before testing.
C. Note the elapsed time and recognize that the test results may not reflect the initial
discharge conditions. [CORRECT]
D. Reject the load immediately without performing any field tests.
Correct Answer: C
Rationale: This choice is correct because the technician must document the actual
conditions observed, including delays that affect the concrete's properties. This aligns with
the principle that field testers report factual data, leaving the decision to accept or reject
the material to the specifying authority.
Q5: You review a batch ticket indicating a target air content of 5.0%. Your field test using the
volumetric method yields a result of 7.2%. What is the most appropriate initial action?
A. Reject the load immediately and send the truck back to the plant.
B. Add more water to the mix to bring the air content down to the target.
C. Document the 7.2% result and notify the supervising engineer or inspector. [CORRECT]
D. Average the ticket value and your field value to report 6.1%.
Correct Answer: C
Rationale: The best answer is to document the 7.2% result and notify the supervising
engineer or inspector. This aligns with the principle that field testers do not have the
authority to reject materials, but must provide the factual data for the engineer to make
that decision.
Q6: What is the required accuracy range for a temperature-measuring device used to test
freshly mixed concrete according to ASTM C1064?
A. ±0.5°F (±0.3°C)
B. ±1.0°F (±0.5°C) [CORRECT]
C. ±2.0°F (±1.0°C)
D. ±5.0°F (±3.0°C)
Correct Answer: C
Rationale: This choice is correct because ASTM C1064 specifies that the temperature-
measuring device must be accurate to within ±1.0°F (±0.5°C) to ensure reliable monitoring
of concrete placement conditions. This matches the principle that precise temperature data
is essential for evaluating compliance with project specifications.
Q7: Before performing a slump test, how should the inside of the slump cone and the base
plate be prepared?
A. They should be coated with a thin layer of form release oil.
B. They should be completely dry to prevent diluting the concrete sample.
C. They should be dampened with water, leaving no standing water. [CORRECT]
D. They should be heated to match the ambient air temperature.
Correct Answer: C
Rationale: The best answer is that they should be dampened with water, leaving no standing
water. This aligns with the principle that a damp surface prevents the dry metal from
