Engineering Circuit Analysis
1. Nodal Analysis: Choose one node as the reference node, and all the other node voltages are defined with
respect to that node. This node also called ground because it has zero potential
2. The value of nodal analysis: once we know nodal voltages we can calculate current, power absorbed
or supplied by any element
3. How does current flow with respect to Voltage?: Current will flow from the node of higher
potential to the node of lower potential.
4. How many linearly independent equation do we need to solve KCL complete-
ly?: N - 1 equation.
5. There are 3 ways to solve KCL: 1. Matlab
2. Gaussian elimination
3. Matrix analysis
6. Ohm's Law: V=IR, GV = I, where G is inductance
7. Matrix Analysis equation: If general form of equation, GV = I
Then , solution will be V = (G^-1)I
8. Matrix Analysis the inverse of G: |G| is determinant
9. The node equation for networks containing only resistors and i ndependent
current sources can be written in .: symmetrical from
10. What is inspection KCL?: In general, if KCL is applied to node j with node voltage v_j , the coeflcient of
v_j is the sum of all the conductances connected to node j and the coeflcients of the other node voltages (e.g., v_j−1,
v_j+1) are the negative of the sum of the conductances connected directly between these nodes and node j. The
right-hand side of the equation is equal to the sum of the currents entering the node via current sources. Therefore,
the left-hand side of the equation represents the sum of the currents leaving node j and the right-hand side of the
equation represents the currents entering node j.
11. Nodal Analysis's omh's law: I = (Vm - Vn) / R
Vm and Vn has to be measured with respect to the same point, that is ground. All the nonreferenc e nodes are
1/9
, measured with respect to only one reference node.
12. If circuit contain dependent source: Then symmetrical condition will not work.
2/9
1. Nodal Analysis: Choose one node as the reference node, and all the other node voltages are defined with
respect to that node. This node also called ground because it has zero potential
2. The value of nodal analysis: once we know nodal voltages we can calculate current, power absorbed
or supplied by any element
3. How does current flow with respect to Voltage?: Current will flow from the node of higher
potential to the node of lower potential.
4. How many linearly independent equation do we need to solve KCL complete-
ly?: N - 1 equation.
5. There are 3 ways to solve KCL: 1. Matlab
2. Gaussian elimination
3. Matrix analysis
6. Ohm's Law: V=IR, GV = I, where G is inductance
7. Matrix Analysis equation: If general form of equation, GV = I
Then , solution will be V = (G^-1)I
8. Matrix Analysis the inverse of G: |G| is determinant
9. The node equation for networks containing only resistors and i ndependent
current sources can be written in .: symmetrical from
10. What is inspection KCL?: In general, if KCL is applied to node j with node voltage v_j , the coeflcient of
v_j is the sum of all the conductances connected to node j and the coeflcients of the other node voltages (e.g., v_j−1,
v_j+1) are the negative of the sum of the conductances connected directly between these nodes and node j. The
right-hand side of the equation is equal to the sum of the currents entering the node via current sources. Therefore,
the left-hand side of the equation represents the sum of the currents leaving node j and the right-hand side of the
equation represents the currents entering node j.
11. Nodal Analysis's omh's law: I = (Vm - Vn) / R
Vm and Vn has to be measured with respect to the same point, that is ground. All the nonreferenc e nodes are
1/9
, measured with respect to only one reference node.
12. If circuit contain dependent source: Then symmetrical condition will not work.
2/9