ALBERTA MASTER ELECTRICIAN CERTIFICATION EXAM
2026/2027 HIGH-YIELD EXAM QUESTIONS & STUDY GUIDE
Table of Contents
Section Domain Approx. Page
Questions Reference
1 Alberta Acts, Regulations & Safety 20 2
Codes
2 Canadian Electrical Code – General 25 5
Rules & Interpretations
3 Electrical Theory & Circuit Calculations 20 9
4 Grounding & Bonding 20 12
5 Overcurrent Protection & Coordination 20 15
6 Wiring Methods, Raceways & Cables 25 18
7 Motors, Controls & HVAC Systems 20 22
8 Load Calculations & Service Sizing 20 25
9 Hazardous Locations & Special 15 28
Occupancies
10 Renewable Energy & Energy Storage 10 30
Systems
11 Emergency Systems & Life Safety 5 31
Total 200
,Section 1: Alberta Acts, Regulations & Safety Codes
(20 Questions – Page 2)
1. Under the Alberta Safety Codes Act, who is ultimately responsible for
ensuring that electrical installations comply with the Canadian Electrical
Code and all applicable permits are obtained?
A) The journeyperson electrician performing the work
B) The master electrician or the designated certified individual
C) The electrical contractor's safety officer
D) The local utility authority
Correct Answer: B
Rationale: The Safety Codes Act places the legal responsibility for code
compliance and permit acquisition on the master electrician or the
certified individual designated by the contractor. While journeypersons
perform the work, the master electrician holds the overall
accountability for regulatory adherence.
2. According to the Alberta Certification and Permit Regulation, what is
the maximum voltage between conductors permitted for work
performed under a restricted master electrician certificate?
A) 120 volts
B) 240 volts
C) 300 volts
D) 600 volts
Correct Answer: C
Rationale: As outlined in the Alberta electrical regulations, a restricted
master electrician certificate limits the holder to electrical installations
,not exceeding 300 volts between conductors and with an ampacity of
not more than 200 amperes.
3. What is the primary role of the Alberta Safety Codes Council
regarding the Master Electrician certification?
A) To issue journeyperson certificates
B) To administer the Master Electrician exam and oversee certification
C) To set the retail price of electrical equipment
D) To perform all electrical inspections in the province
Correct Answer: B
Rationale: The Safety Codes Council is the accredited body responsible
for administering the Master Electrician examination, issuing
certifications, and ensuring that candidates meet the required
experience and knowledge standards.
4. Under the Alberta Occupational Health and Safety (OHS) Code, what
is the minimum approach distance for an unqualified worker to exposed
energized electrical equipment operating at 750 volts?
A) 300 mm
B) 1,000 mm
C) 3,000 mm
D) 5,000 mm
Correct Answer: B
Rationale: The Alberta OHS Code specifies minimum approach
distances based on voltage. For 750 volts, the limit of approach for
unqualified workers is typically 1,000 mm (1 meter). This distance
increases with higher voltages.
5. What is the required period within which an employer must report a
serious electrical incident to Alberta Occupational Health and Safety?
, A) Immediately
B) Within 24 hours
C) Within 72 hours
D) Within 7 days
Correct Answer: A
Rationale: The Alberta OHS Act requires that serious incidents,
including those involving electrical contact that results in serious injury
or death, must be reported to OHS immediately. A written report must
follow within 24 hours.
6. According to the Alberta Electrical Utility Code, what is the typical
maximum allowable voltage drop for a consumer's service from the
utility point of supply to the service equipment?
A) 1%
B) 3%
C) 5%
D) 6%
Correct Answer: B
Rationale: The Alberta Electrical Utility Code and the Canadian
Electrical Code generally recommend a maximum voltage drop of 3% on
a consumer's service or a branch circuit, and a total of 5% from the
service point to the furthest outlet.
7. In Alberta, what is the primary purpose of the Electrical STANDATA?
A) To replace the Canadian Electrical Code
B) To provide interpretations, clarifications, and Alberta-specific
amendments to the CEC
C) To list the prices of electrical components
D) To certify electrical equipment for sale
2026/2027 HIGH-YIELD EXAM QUESTIONS & STUDY GUIDE
Table of Contents
Section Domain Approx. Page
Questions Reference
1 Alberta Acts, Regulations & Safety 20 2
Codes
2 Canadian Electrical Code – General 25 5
Rules & Interpretations
3 Electrical Theory & Circuit Calculations 20 9
4 Grounding & Bonding 20 12
5 Overcurrent Protection & Coordination 20 15
6 Wiring Methods, Raceways & Cables 25 18
7 Motors, Controls & HVAC Systems 20 22
8 Load Calculations & Service Sizing 20 25
9 Hazardous Locations & Special 15 28
Occupancies
10 Renewable Energy & Energy Storage 10 30
Systems
11 Emergency Systems & Life Safety 5 31
Total 200
,Section 1: Alberta Acts, Regulations & Safety Codes
(20 Questions – Page 2)
1. Under the Alberta Safety Codes Act, who is ultimately responsible for
ensuring that electrical installations comply with the Canadian Electrical
Code and all applicable permits are obtained?
A) The journeyperson electrician performing the work
B) The master electrician or the designated certified individual
C) The electrical contractor's safety officer
D) The local utility authority
Correct Answer: B
Rationale: The Safety Codes Act places the legal responsibility for code
compliance and permit acquisition on the master electrician or the
certified individual designated by the contractor. While journeypersons
perform the work, the master electrician holds the overall
accountability for regulatory adherence.
2. According to the Alberta Certification and Permit Regulation, what is
the maximum voltage between conductors permitted for work
performed under a restricted master electrician certificate?
A) 120 volts
B) 240 volts
C) 300 volts
D) 600 volts
Correct Answer: C
Rationale: As outlined in the Alberta electrical regulations, a restricted
master electrician certificate limits the holder to electrical installations
,not exceeding 300 volts between conductors and with an ampacity of
not more than 200 amperes.
3. What is the primary role of the Alberta Safety Codes Council
regarding the Master Electrician certification?
A) To issue journeyperson certificates
B) To administer the Master Electrician exam and oversee certification
C) To set the retail price of electrical equipment
D) To perform all electrical inspections in the province
Correct Answer: B
Rationale: The Safety Codes Council is the accredited body responsible
for administering the Master Electrician examination, issuing
certifications, and ensuring that candidates meet the required
experience and knowledge standards.
4. Under the Alberta Occupational Health and Safety (OHS) Code, what
is the minimum approach distance for an unqualified worker to exposed
energized electrical equipment operating at 750 volts?
A) 300 mm
B) 1,000 mm
C) 3,000 mm
D) 5,000 mm
Correct Answer: B
Rationale: The Alberta OHS Code specifies minimum approach
distances based on voltage. For 750 volts, the limit of approach for
unqualified workers is typically 1,000 mm (1 meter). This distance
increases with higher voltages.
5. What is the required period within which an employer must report a
serious electrical incident to Alberta Occupational Health and Safety?
, A) Immediately
B) Within 24 hours
C) Within 72 hours
D) Within 7 days
Correct Answer: A
Rationale: The Alberta OHS Act requires that serious incidents,
including those involving electrical contact that results in serious injury
or death, must be reported to OHS immediately. A written report must
follow within 24 hours.
6. According to the Alberta Electrical Utility Code, what is the typical
maximum allowable voltage drop for a consumer's service from the
utility point of supply to the service equipment?
A) 1%
B) 3%
C) 5%
D) 6%
Correct Answer: B
Rationale: The Alberta Electrical Utility Code and the Canadian
Electrical Code generally recommend a maximum voltage drop of 3% on
a consumer's service or a branch circuit, and a total of 5% from the
service point to the furthest outlet.
7. In Alberta, what is the primary purpose of the Electrical STANDATA?
A) To replace the Canadian Electrical Code
B) To provide interpretations, clarifications, and Alberta-specific
amendments to the CEC
C) To list the prices of electrical components
D) To certify electrical equipment for sale
