NACE/AMPP Practice Test – Questions With A+
Solutions
Add to calendar
Play your way to mastery with fun games
Match Blocks Charms NEW
Terms in this set (100)
,You are the NACE Inspector on a tank B. Document the problem and advise the Contractor
lining project where a 50 % solids and Owner's representative
epoxy tank lining is being applied.
After application of the 19 coat you
notice small blisters in some areas of
the applied lining. Your FIRST preferred
course of action is to:
A. Break the blisters to see what's
inside
B. Document the problem and advise
the Contractor and Owner's
representative
C. Document the problem and advise
the Contractor
D. Extract any liquid that may be inside
the blister and send it to the lab for
further analysis
The dew point is the temperature at C. condensation occurs
which
A. water freezes
B. humidity decreases
C. condensation occurs
D. the air is saturated
,If a contractor is using a poorly C. blotter test for the presence of oil and water
maintained compressor to supply air
for abrasive blast cleaning and
conventional airspray, the coating
inspector should perform a
A. dry film thickness ( DEI )
measurement
B. wet film thickness ( WFT )
measurement
C. blotter test for the presence of oil
and water
D. vial lest
Upon arrival of coating materials , the B. observe and document the amount of material and
inspector should batch numbers
A. review coating contractors ' plans
for storage of coating materials and
confirm they meet national , local and
owners ' fire and environmental
regulations
B. observe and document the amount
of material and batch numbers
C. observe aryl document that the
applicator WFT at regular intervals
during application
D. observe and document time frame
and environmental conditions between
each coat
, Relative humidity is A. a measure of the amount of moisture in the air
A. a measure of the amount of compared to saturation level .
moisture in the air compared to
saturation level
B. a measure of the amount of moisture
in the air compared to the air
temperature
C. the lowest temperature at which
moisture forms on a steel surface
D. the highest temperature at which
moisture forms on a steel surface .
Galvanic corrosion occurs on which of C. Metal
the following substrates
A. Concrete
B. Fiberglass Reinforced Plastic
C. Metal
D. Wood
When applying Thermal Spray D. SSPC - CS 23.00 / AWS C2.23 / NACE No. 12
Coatings the specification is most likely
to refence
A. SSPC PA 2
B. NACE SP 0178
C. NACE SP 0188
D. SSPC - CS 23.00 / AWS C2.23 /
NACE No. 12
What is the minimum recommended B. 2.5 cm ( 1 inch )
distance away from an edge that an
inspector should take a measurement
with a dial - type magnetic pull - off
Dry Film Thickness ( DFT ) gauge ?
A. 1 cm ( .39 inch )
B. 2.5 cm ( 1 inch )
C. 6.35 cm ( 2.5 inch )
D. 2.5 millimeters ( .10 inch )
Solutions
Add to calendar
Play your way to mastery with fun games
Match Blocks Charms NEW
Terms in this set (100)
,You are the NACE Inspector on a tank B. Document the problem and advise the Contractor
lining project where a 50 % solids and Owner's representative
epoxy tank lining is being applied.
After application of the 19 coat you
notice small blisters in some areas of
the applied lining. Your FIRST preferred
course of action is to:
A. Break the blisters to see what's
inside
B. Document the problem and advise
the Contractor and Owner's
representative
C. Document the problem and advise
the Contractor
D. Extract any liquid that may be inside
the blister and send it to the lab for
further analysis
The dew point is the temperature at C. condensation occurs
which
A. water freezes
B. humidity decreases
C. condensation occurs
D. the air is saturated
,If a contractor is using a poorly C. blotter test for the presence of oil and water
maintained compressor to supply air
for abrasive blast cleaning and
conventional airspray, the coating
inspector should perform a
A. dry film thickness ( DEI )
measurement
B. wet film thickness ( WFT )
measurement
C. blotter test for the presence of oil
and water
D. vial lest
Upon arrival of coating materials , the B. observe and document the amount of material and
inspector should batch numbers
A. review coating contractors ' plans
for storage of coating materials and
confirm they meet national , local and
owners ' fire and environmental
regulations
B. observe and document the amount
of material and batch numbers
C. observe aryl document that the
applicator WFT at regular intervals
during application
D. observe and document time frame
and environmental conditions between
each coat
, Relative humidity is A. a measure of the amount of moisture in the air
A. a measure of the amount of compared to saturation level .
moisture in the air compared to
saturation level
B. a measure of the amount of moisture
in the air compared to the air
temperature
C. the lowest temperature at which
moisture forms on a steel surface
D. the highest temperature at which
moisture forms on a steel surface .
Galvanic corrosion occurs on which of C. Metal
the following substrates
A. Concrete
B. Fiberglass Reinforced Plastic
C. Metal
D. Wood
When applying Thermal Spray D. SSPC - CS 23.00 / AWS C2.23 / NACE No. 12
Coatings the specification is most likely
to refence
A. SSPC PA 2
B. NACE SP 0178
C. NACE SP 0188
D. SSPC - CS 23.00 / AWS C2.23 /
NACE No. 12
What is the minimum recommended B. 2.5 cm ( 1 inch )
distance away from an edge that an
inspector should take a measurement
with a dial - type magnetic pull - off
Dry Film Thickness ( DFT ) gauge ?
A. 1 cm ( .39 inch )
B. 2.5 cm ( 1 inch )
C. 6.35 cm ( 2.5 inch )
D. 2.5 millimeters ( .10 inch )
