LADWP Electrical Craft Helper
Comprehensive Resource To Help You Ace 2026-2027 Exams
Includes Frequently Tested Questions With ELABORATED
100% Correct COMPLETE SOLUTIONS
Guaranteed Pass First Attempt!! Current Update!!
1. Special type of saw blade used on a power saw for cutting material such as,
cement block, brick and sheet metal, is called an - Correct Answer:
Abrasive cutoff wheel
2. Once a hacksaw has started to bite into a piece of conduit the strokes in
cutting should - Correct Answer: Use the full length of the blade
3. The tool best used to hold an object to be filed is - Correct Answer: A
vise
4. Which of the following is the best hammer to use for pounding a damaged
signpost anchor in the ground - Correct Answer: Sledge
5. A rat tail file is - Correct Answer: A round, thin and pointed file used to
smooth the inside of a drilled rimless lens hole.
6. Which of the following is best to use to remove large nuts and bolts -
Correct Answer: Open end wrench
,7. The tools used to determine whether a pipe is plumb is a - Correct
Answer: Level
8. The tool commonly used for testing the hardness of metal before cutting it
with a hacksaw blade - Correct Answer: Carborundum stone
9. Best type of saw to use to cut a 3-foot long, 2x6 down to a 3 foot long, 2x4
is a - Correct Answer: Rip saw
10.The best tool to use to smooth the inside of the cut-off end of a pipe is a/a -
Correct Answer: Reamer
11.Which tool would most likely be used to repack a brick mortar joint -
Correct Answer: Tuck pointer
12.For bending reinforcing bars in a foundation, it is usually best to use a -
Correct Answer: Hickey
13.Best tool you will most likely need when using a star drill in concrete is a -
Correct Answer: Rotary hammer
14.Which practice is the most important in keeping tools from rusting -
Correct Answer: Coat tools with a little bit of oil
,15.Shovels used for mixing concrete by hand should have a - Correct
Answer: Round point
16.That wrench that is used in a manner similar to a screwdriver is a/an -
Correct Answer: Allen wrench
17.A pipe wrench is least likely to be used for loosening a pipe - Correct
Answer: Tee
18.Tool used best to make a hole 5 1/2 inches in diameter in a wooden floor is
number (fig2) - Correct Answer: 50
19.Tool used best to use to make the shoulder cuts on a tenon is number (fig2)
- Correct Answer: 41
20.Figure 39 is a (fig2) - Correct Answer: Rip saw
21.Figure 34 (fig2) - Correct Answer: Scratch awl
22.Fig 38 (fig2) - Correct Answer: Sliding bevel
23.Fig 59 (fig2) - Correct Answer: Saw set
24.Fig 58 - Correct Answer: Flooring chisel
, 25.Part of a drill press used to hold the drills is called the - Correct Answer:
Chuck
26.Which one is commonly used to make scratch marks on sheet metal?
(Figure 2) - Correct Answer: 32 (scratch awl)
27.A tri square is shown at number (fig1) - Correct Answer: 16
28.Craft worker that is most likely to use tool number 26 is a - Correct
Answer: Bricklayer
29.To make a wood screw flush with the wood surface, best tool to use is (fig1)
- Correct Answer: 41
30.Which tool is commonly used in setting the head of number 34 (fig1) -
Correct Answer: 39
31.A caliper is shown at number (fig1) - Correct Answer: D none of the
above (ask)
32.A plastering tool useful as a hand table in order to carry plaster is called a -
Correct Answer: Hawk
Comprehensive Resource To Help You Ace 2026-2027 Exams
Includes Frequently Tested Questions With ELABORATED
100% Correct COMPLETE SOLUTIONS
Guaranteed Pass First Attempt!! Current Update!!
1. Special type of saw blade used on a power saw for cutting material such as,
cement block, brick and sheet metal, is called an - Correct Answer:
Abrasive cutoff wheel
2. Once a hacksaw has started to bite into a piece of conduit the strokes in
cutting should - Correct Answer: Use the full length of the blade
3. The tool best used to hold an object to be filed is - Correct Answer: A
vise
4. Which of the following is the best hammer to use for pounding a damaged
signpost anchor in the ground - Correct Answer: Sledge
5. A rat tail file is - Correct Answer: A round, thin and pointed file used to
smooth the inside of a drilled rimless lens hole.
6. Which of the following is best to use to remove large nuts and bolts -
Correct Answer: Open end wrench
,7. The tools used to determine whether a pipe is plumb is a - Correct
Answer: Level
8. The tool commonly used for testing the hardness of metal before cutting it
with a hacksaw blade - Correct Answer: Carborundum stone
9. Best type of saw to use to cut a 3-foot long, 2x6 down to a 3 foot long, 2x4
is a - Correct Answer: Rip saw
10.The best tool to use to smooth the inside of the cut-off end of a pipe is a/a -
Correct Answer: Reamer
11.Which tool would most likely be used to repack a brick mortar joint -
Correct Answer: Tuck pointer
12.For bending reinforcing bars in a foundation, it is usually best to use a -
Correct Answer: Hickey
13.Best tool you will most likely need when using a star drill in concrete is a -
Correct Answer: Rotary hammer
14.Which practice is the most important in keeping tools from rusting -
Correct Answer: Coat tools with a little bit of oil
,15.Shovels used for mixing concrete by hand should have a - Correct
Answer: Round point
16.That wrench that is used in a manner similar to a screwdriver is a/an -
Correct Answer: Allen wrench
17.A pipe wrench is least likely to be used for loosening a pipe - Correct
Answer: Tee
18.Tool used best to make a hole 5 1/2 inches in diameter in a wooden floor is
number (fig2) - Correct Answer: 50
19.Tool used best to use to make the shoulder cuts on a tenon is number (fig2)
- Correct Answer: 41
20.Figure 39 is a (fig2) - Correct Answer: Rip saw
21.Figure 34 (fig2) - Correct Answer: Scratch awl
22.Fig 38 (fig2) - Correct Answer: Sliding bevel
23.Fig 59 (fig2) - Correct Answer: Saw set
24.Fig 58 - Correct Answer: Flooring chisel
, 25.Part of a drill press used to hold the drills is called the - Correct Answer:
Chuck
26.Which one is commonly used to make scratch marks on sheet metal?
(Figure 2) - Correct Answer: 32 (scratch awl)
27.A tri square is shown at number (fig1) - Correct Answer: 16
28.Craft worker that is most likely to use tool number 26 is a - Correct
Answer: Bricklayer
29.To make a wood screw flush with the wood surface, best tool to use is (fig1)
- Correct Answer: 41
30.Which tool is commonly used in setting the head of number 34 (fig1) -
Correct Answer: 39
31.A caliper is shown at number (fig1) - Correct Answer: D none of the
above (ask)
32.A plastering tool useful as a hand table in order to carry plaster is called a -
Correct Answer: Hawk
