LESSON 2: INTRODUCTION TO INSTRUMENTATION
EXAM QUIZZES WITH ACCURATE ANSWERS .
The typical working environment for an instrument technician ? .
Select one:
a.consists of indoor work that is climate controlled
b.is always safe and clean
c.rarely changes from day to day
d.varies greatly and frequently involves hazardous conditions - correct Answers -varies greatly
and frequently involves hazardous conditions
To ? a process is to cause a system to act or function in a certain way.
Select one:
a.calibrate
b.control
c.loop check
d.troubleshoot - correct Answers -control
Who may remove a technician's lock in a lockout/tagout system?
Select one:
a.A supervisor
b.Any technician involved in the lockout/tagout procedure
c.The plant owner's representative
d.The technician who installed the lock - correct Answers -The technician who installed the lock
Lockout/tagout procedures are only used to eliminate electrical hazards.
Select one:
1
, True
False - correct Answers -False
A technician working in a refinery is required to open a process line that was previously in use.
What document can the technician use to select the proper personal protective equipment?
Select one:
a.Confined space permit
b.Hot work permit
c.NFPA 70E
d.Safety data sheet - correct Answers -Safety data sheet
When working on elevated surfaces or near openings, the technician should complete a ? before
beginning work.
Select one:
a.confined space permit
b.fall protection plan
c.hot work permit
d.line break analysis - correct Answers -fall protection plan
What defines a confined space?I. A space large enough for a worker to bodily enter and perform
assigned workII. A space not designed for continuous human occupancyIII. A space that is not
temperature controlledIV. A space with limited means for entry or exitV. A space with process
piping - correct Answers -I., II., and IV.
An extension ladder 28 feet long is leaning against a building wall. What is the proper distance
the base of the ladder should be from the building wall?
Select one:
a.2.8'
b.4'
c.7'
2
EXAM QUIZZES WITH ACCURATE ANSWERS .
The typical working environment for an instrument technician ? .
Select one:
a.consists of indoor work that is climate controlled
b.is always safe and clean
c.rarely changes from day to day
d.varies greatly and frequently involves hazardous conditions - correct Answers -varies greatly
and frequently involves hazardous conditions
To ? a process is to cause a system to act or function in a certain way.
Select one:
a.calibrate
b.control
c.loop check
d.troubleshoot - correct Answers -control
Who may remove a technician's lock in a lockout/tagout system?
Select one:
a.A supervisor
b.Any technician involved in the lockout/tagout procedure
c.The plant owner's representative
d.The technician who installed the lock - correct Answers -The technician who installed the lock
Lockout/tagout procedures are only used to eliminate electrical hazards.
Select one:
1
, True
False - correct Answers -False
A technician working in a refinery is required to open a process line that was previously in use.
What document can the technician use to select the proper personal protective equipment?
Select one:
a.Confined space permit
b.Hot work permit
c.NFPA 70E
d.Safety data sheet - correct Answers -Safety data sheet
When working on elevated surfaces or near openings, the technician should complete a ? before
beginning work.
Select one:
a.confined space permit
b.fall protection plan
c.hot work permit
d.line break analysis - correct Answers -fall protection plan
What defines a confined space?I. A space large enough for a worker to bodily enter and perform
assigned workII. A space not designed for continuous human occupancyIII. A space that is not
temperature controlledIV. A space with limited means for entry or exitV. A space with process
piping - correct Answers -I., II., and IV.
An extension ladder 28 feet long is leaning against a building wall. What is the proper distance
the base of the ladder should be from the building wall?
Select one:
a.2.8'
b.4'
c.7'
2
