AMPP CIP LEVEL 1 REVIEWS MAIN ANSWERS AND
QUESTIONS SET A+
✔✔How large is a unit area when inspecting for staining - ✔✔9 inches
✔✔Abrasive regulator valve - ✔✔Controls the amount of embrace of being fed into the
airstream
✔✔Main air inlet valve - ✔✔Starts and stops the abrasive blast operation
✔✔Air compressor - ✔✔Supplies air through a hose at high speed and volume
✔✔Dryer - ✔✔Removes moisture from the compressed air
✔✔Blast pot - ✔✔Mixes abrasive with compressed air
✔✔CO monitor - ✔✔Detect carbon monoxide
✔✔Blast hose - ✔✔Carries the abrasive and pressurized air to the nozzle
✔✔SSPC - SP7 - ✔✔Brush off blast cleaning
✔✔SSPC - SP 14 - ✔✔Industrial blast cleaning- 10% of mill scale, rust and coating in
each unit area of the surface
✔✔SSPC - SP6 - ✔✔Commercial blast cleaning - 33% staining of each unit area
✔✔SSPC - SP 10 - ✔✔Near white metal blast cleaning - 5% staining of each unit area
of surface
✔✔SSPC - SP5 - ✔✔White metal blast cleaning - no stains allowed
✔✔SSPC-VIS 5/NACE VIS 9 - ✔✔Wet Abrasive Blast Cleaning.
, ✔✔Three types of flash rust - ✔✔Light flash, rust, moderate flash rust, heavy flash rust
✔✔Six media properties - ✔✔Hardness, shape, size, density, friability, reusability
✔✔Media shapes - ✔✔Shot- rounded, grit - angular
✔✔Standard for indicating oil in abrasives - ✔✔ASTM - D7393
✔✔Standard for sieve analysis of fine and course aggregates - ✔✔ASTM - C136
✔✔SSPC - AB1 - ✔✔Mineral and slag abrasives
✔✔SSPC - AB2 - ✔✔Cleanliness of recycled, Ferris metallic abrasives
✔✔SSPC - AB3 - ✔✔Ferris metallic abrasives
✔✔SSPC - AB4 - ✔✔Recyclable encapsulated abrasives
✔✔Layers within a coating system - ✔✔Primers, intermediate coats, topcoat
✔✔Generic Coating Types - ✔✔Latex emulsions - water-based, Alkyd- oil based,
epoxy, fluoropolymer, inorganic zinc - rich, organic zinc-rich, polyaspartic, polyester,
polysiloxane and siloxane, polyurea, polyurethane, silicone, vinyl, vinyl Esthers
✔✔Which coating cures the fastest - ✔✔Polyurea
✔✔Isocyanates are a safety concern with which coating type - ✔✔Polyurethane
✔✔Viscosity - ✔✔A liquid's resistance to flowing
✔✔Shelf life - ✔✔The length of time from a date of manufacturer that a coating remains
usable when stored in its original container
✔✔Pot life - ✔✔The length of time after mixing that coatings remain usable and can be
correctly applied
✔✔Induction time - ✔✔The length of time that must relapse after mixing, but before
application that is necessary for the chemical reaction to take place. Also known as
sweat in or stand in time.
✔✔Thinners - ✔✔Used to reduce viscosity prior to application to achieve a more
consistent spray, pattern, or film.
QUESTIONS SET A+
✔✔How large is a unit area when inspecting for staining - ✔✔9 inches
✔✔Abrasive regulator valve - ✔✔Controls the amount of embrace of being fed into the
airstream
✔✔Main air inlet valve - ✔✔Starts and stops the abrasive blast operation
✔✔Air compressor - ✔✔Supplies air through a hose at high speed and volume
✔✔Dryer - ✔✔Removes moisture from the compressed air
✔✔Blast pot - ✔✔Mixes abrasive with compressed air
✔✔CO monitor - ✔✔Detect carbon monoxide
✔✔Blast hose - ✔✔Carries the abrasive and pressurized air to the nozzle
✔✔SSPC - SP7 - ✔✔Brush off blast cleaning
✔✔SSPC - SP 14 - ✔✔Industrial blast cleaning- 10% of mill scale, rust and coating in
each unit area of the surface
✔✔SSPC - SP6 - ✔✔Commercial blast cleaning - 33% staining of each unit area
✔✔SSPC - SP 10 - ✔✔Near white metal blast cleaning - 5% staining of each unit area
of surface
✔✔SSPC - SP5 - ✔✔White metal blast cleaning - no stains allowed
✔✔SSPC-VIS 5/NACE VIS 9 - ✔✔Wet Abrasive Blast Cleaning.
, ✔✔Three types of flash rust - ✔✔Light flash, rust, moderate flash rust, heavy flash rust
✔✔Six media properties - ✔✔Hardness, shape, size, density, friability, reusability
✔✔Media shapes - ✔✔Shot- rounded, grit - angular
✔✔Standard for indicating oil in abrasives - ✔✔ASTM - D7393
✔✔Standard for sieve analysis of fine and course aggregates - ✔✔ASTM - C136
✔✔SSPC - AB1 - ✔✔Mineral and slag abrasives
✔✔SSPC - AB2 - ✔✔Cleanliness of recycled, Ferris metallic abrasives
✔✔SSPC - AB3 - ✔✔Ferris metallic abrasives
✔✔SSPC - AB4 - ✔✔Recyclable encapsulated abrasives
✔✔Layers within a coating system - ✔✔Primers, intermediate coats, topcoat
✔✔Generic Coating Types - ✔✔Latex emulsions - water-based, Alkyd- oil based,
epoxy, fluoropolymer, inorganic zinc - rich, organic zinc-rich, polyaspartic, polyester,
polysiloxane and siloxane, polyurea, polyurethane, silicone, vinyl, vinyl Esthers
✔✔Which coating cures the fastest - ✔✔Polyurea
✔✔Isocyanates are a safety concern with which coating type - ✔✔Polyurethane
✔✔Viscosity - ✔✔A liquid's resistance to flowing
✔✔Shelf life - ✔✔The length of time from a date of manufacturer that a coating remains
usable when stored in its original container
✔✔Pot life - ✔✔The length of time after mixing that coatings remain usable and can be
correctly applied
✔✔Induction time - ✔✔The length of time that must relapse after mixing, but before
application that is necessary for the chemical reaction to take place. Also known as
sweat in or stand in time.
✔✔Thinners - ✔✔Used to reduce viscosity prior to application to achieve a more
consistent spray, pattern, or film.
