SUPERVISOR NJ CORRECT FINAL ANSWERS AND
QUESTIONS SET A+
✔✔Where should the GFCI units be connected? - ✔✔GFCI units should be connected
at the main power source panel.
✔✔Tag & lock Out systems: - ✔✔A system to de-energize electrical, hydraulic thermal,
or any other energy source to prevent accidental activation of such a system.
✔✔Glove bags should have the following, except? - ✔✔A screen to control pressure.
✔✔Why is it not permitted to use glove bags above 150 F ? - ✔✔Because the plastic
and the duct tape can come apart.
✔✔What should be done if an asbestos bag rips or breaks? - ✔✔Keep ACM wet, and
put broken bag and waste into another bag.
✔✔ACM waste: - ✔✔Must be transported in a truck that is separated from the
conductors cabin, and its covered with two 2 layers of poly.
✔✔Which agencies regulate the transportation of ACM waste? - ✔✔US-EPA & US-DOT
✔✔According to OSHA regulations, What respirator should be used if the concentration
were 2 f/cc? - ✔✔Type "C", Pressure demand
✔✔Can an operation and Maintenance (O&M) worker in the event of an emergency
remove ACM equivalent to a large asbestos project?(Large project means > 260 linear
ft or > 160 ft ^2) - ✔✔No, because O&M workers are limited to the removal of only one
asbestos bag.
✔✔What is the last piece of PPE (Personal protection equipment) that the worker puts
on before entering the work area? - ✔✔The gloves
, ✔✔Where should OSHA signs be placed at? - ✔✔At every entrance to the work area.
✔✔Where do you store your street cloths? - ✔✔In the clean room
✔✔The personal decontamination chamber is composed of the following, except? -
✔✔The work area
✔✔Where do you take your suit off? - ✔✔In the equipment (dirty) room
✔✔Where do you take off your respirator? - ✔✔In the shower, while taking the shower.
✔✔A type "C" compression system is used to provide respiratory protection for 12
workers. The compressor has a capacity of 30 CFM, each of the 12 lines extends for
150ft. Workers are complaining of not getting enough air. What could be the problem? -
✔✔The compressor doesn't have enough capacity.
✔✔What is not considered active abatement? - ✔✔Removal of critical barriers/because
critical barriers are Removed only after passing final air samples <0.010 f/cc or the
background level, which ever is greater
✔✔What kind of air samples are used to measure exposure to employees? - ✔✔OSHA
requires PCM (Phase contrast microscopy)
✔✔If theres a breach in the negative pressure enclosure such as a puncture in the floor
or wall poly what must be done? - ✔✔Whoever notices the problem must fix it
immediately.
✔✔If no exposure assessment has been made to determine the exposure to the worker
before work commences. What does OSHA require for minimum respiratory protection?
- ✔✔The employees must issue a Type C pressure demand respirator , or any other
positive pressure respirator (such as a PAPR
✔✔When should the employer notified the results of employee exposure? - ✔✔The
employer must notify affected employees of the monitoring results that represents that
employees exposure as soon as possible following the receipt of the monitoring results.
✔✔How should the employer notified affected employees of the results of employee
exposure? - ✔✔The employer shall notify affected employees of the results of
monitoring representing the employees -exposure in writing either individually or by
posting them at a centrally located place that is accessible to affected employees.
✔✔An MSDS sheets material safety data sheets - must accompany every chemical in
inventory at the work site. - ✔✔...
QUESTIONS SET A+
✔✔Where should the GFCI units be connected? - ✔✔GFCI units should be connected
at the main power source panel.
✔✔Tag & lock Out systems: - ✔✔A system to de-energize electrical, hydraulic thermal,
or any other energy source to prevent accidental activation of such a system.
✔✔Glove bags should have the following, except? - ✔✔A screen to control pressure.
✔✔Why is it not permitted to use glove bags above 150 F ? - ✔✔Because the plastic
and the duct tape can come apart.
✔✔What should be done if an asbestos bag rips or breaks? - ✔✔Keep ACM wet, and
put broken bag and waste into another bag.
✔✔ACM waste: - ✔✔Must be transported in a truck that is separated from the
conductors cabin, and its covered with two 2 layers of poly.
✔✔Which agencies regulate the transportation of ACM waste? - ✔✔US-EPA & US-DOT
✔✔According to OSHA regulations, What respirator should be used if the concentration
were 2 f/cc? - ✔✔Type "C", Pressure demand
✔✔Can an operation and Maintenance (O&M) worker in the event of an emergency
remove ACM equivalent to a large asbestos project?(Large project means > 260 linear
ft or > 160 ft ^2) - ✔✔No, because O&M workers are limited to the removal of only one
asbestos bag.
✔✔What is the last piece of PPE (Personal protection equipment) that the worker puts
on before entering the work area? - ✔✔The gloves
, ✔✔Where should OSHA signs be placed at? - ✔✔At every entrance to the work area.
✔✔Where do you store your street cloths? - ✔✔In the clean room
✔✔The personal decontamination chamber is composed of the following, except? -
✔✔The work area
✔✔Where do you take your suit off? - ✔✔In the equipment (dirty) room
✔✔Where do you take off your respirator? - ✔✔In the shower, while taking the shower.
✔✔A type "C" compression system is used to provide respiratory protection for 12
workers. The compressor has a capacity of 30 CFM, each of the 12 lines extends for
150ft. Workers are complaining of not getting enough air. What could be the problem? -
✔✔The compressor doesn't have enough capacity.
✔✔What is not considered active abatement? - ✔✔Removal of critical barriers/because
critical barriers are Removed only after passing final air samples <0.010 f/cc or the
background level, which ever is greater
✔✔What kind of air samples are used to measure exposure to employees? - ✔✔OSHA
requires PCM (Phase contrast microscopy)
✔✔If theres a breach in the negative pressure enclosure such as a puncture in the floor
or wall poly what must be done? - ✔✔Whoever notices the problem must fix it
immediately.
✔✔If no exposure assessment has been made to determine the exposure to the worker
before work commences. What does OSHA require for minimum respiratory protection?
- ✔✔The employees must issue a Type C pressure demand respirator , or any other
positive pressure respirator (such as a PAPR
✔✔When should the employer notified the results of employee exposure? - ✔✔The
employer must notify affected employees of the monitoring results that represents that
employees exposure as soon as possible following the receipt of the monitoring results.
✔✔How should the employer notified affected employees of the results of employee
exposure? - ✔✔The employer shall notify affected employees of the results of
monitoring representing the employees -exposure in writing either individually or by
posting them at a centrally located place that is accessible to affected employees.
✔✔An MSDS sheets material safety data sheets - must accompany every chemical in
inventory at the work site. - ✔✔...
