MICHIGAN STATE BRAKES CERTIFICATION EXAM LATEST 2026 UPDATED
QUESTIONS AND VERIFIED 100% SOLUTIONS (2026/2027) GRADE:
A+|STATUS: GUARANTEED PASS
Most anti-lock brake systems require the removal of the pressure modulator fuse when: -
Answers -a "spaced-saver" spare tire is being used and mismatched tires are being installed
What does a load sensing proportioning valve do? - Answers -It increases the hydraulic pressure
during braking at the rear wheel cylinders when the vehicle is loaded
Which of the following is a true statement about proportioning valves? - Answers -They provide
better braking balance during hard stops
A properly functioning load sensing proportioning valve will: - Answers -cause an increase in the
hydraulic pressure during braking at the rear wheel cylinders when the vehicle is loaded.
Why don't disc brake system usually need adjustment? - Answers -A certain amount of pressure
is maintained by the metering valve
Which of the following would be the LEAST likely cause for an intermittent problem in an ABS
system? - Answers -Open wheel sensor circuit
1|Page
, Which of the following incorrect service procedures could cause brake pedal pulsation? -
Answers -incorrect run-out on the car brake lathe
What type of rotor surface provides the best braking with new pads? - Answers -A smooth, flat
surface
which of the following is a quick way to isolated a defective master cylinder? There are no
external leaks in the system. - Answers -pump up the brake pedal, then hold it firm. if the pedal
slowly drops to the floor, the master cylinder may be defective.
A common cause of pedal pulsation during brake application is: - Answers -NOT caused by
improperly torqued wheels, damaged backing plates, or lubricated shims
the car is at reset. When you slowly apply the brake pedal you hear a squeaking noise at the
rear of the vehicle. what could cause this noise? - Answers -dry backing plate contact surfaces
While test driving a car, the mechanic finds that the right front brake "grabs". The most likely
cause of this problem is: - Answers -brake fluid or grease on the brake linings
Wheel speed sensors: - Answers -send an A/C signal to the control module
2|Page
QUESTIONS AND VERIFIED 100% SOLUTIONS (2026/2027) GRADE:
A+|STATUS: GUARANTEED PASS
Most anti-lock brake systems require the removal of the pressure modulator fuse when: -
Answers -a "spaced-saver" spare tire is being used and mismatched tires are being installed
What does a load sensing proportioning valve do? - Answers -It increases the hydraulic pressure
during braking at the rear wheel cylinders when the vehicle is loaded
Which of the following is a true statement about proportioning valves? - Answers -They provide
better braking balance during hard stops
A properly functioning load sensing proportioning valve will: - Answers -cause an increase in the
hydraulic pressure during braking at the rear wheel cylinders when the vehicle is loaded.
Why don't disc brake system usually need adjustment? - Answers -A certain amount of pressure
is maintained by the metering valve
Which of the following would be the LEAST likely cause for an intermittent problem in an ABS
system? - Answers -Open wheel sensor circuit
1|Page
, Which of the following incorrect service procedures could cause brake pedal pulsation? -
Answers -incorrect run-out on the car brake lathe
What type of rotor surface provides the best braking with new pads? - Answers -A smooth, flat
surface
which of the following is a quick way to isolated a defective master cylinder? There are no
external leaks in the system. - Answers -pump up the brake pedal, then hold it firm. if the pedal
slowly drops to the floor, the master cylinder may be defective.
A common cause of pedal pulsation during brake application is: - Answers -NOT caused by
improperly torqued wheels, damaged backing plates, or lubricated shims
the car is at reset. When you slowly apply the brake pedal you hear a squeaking noise at the
rear of the vehicle. what could cause this noise? - Answers -dry backing plate contact surfaces
While test driving a car, the mechanic finds that the right front brake "grabs". The most likely
cause of this problem is: - Answers -brake fluid or grease on the brake linings
Wheel speed sensors: - Answers -send an A/C signal to the control module
2|Page
