ASME SECTION 9 EXAM ACTUAL EXAM 2026 |
WELDING, BRAZING, AND FUSING || MOST RECENT
EXAM 2026|2027 ACTUAL COMPLETE REAL EXAM
QUESTIONS AND CORRECT ANSWERS (VERIFIED
ANSWERS) ALREADY GRADED A+ | GUARANTEED
SUCCESS!! NEWEST EXAM | JUST RELEASED!!
A repair organization has a WPS which states it is qualified for
P-8 to P-8 material welded with either E308, E308L, E309, E316,
electrodes (SMAW process). The PQR, supporting this WPS,
states the weld test coupons were SA-240 Type 304L material,
welded with E308 electrodes. Is the WPS properly qualified for
the base material listed?
A. Yes
B. No
C. Not enough information given
D. Yes, if properly heat treated - ANSWER-A
What positions are necessary to qualify a welder for all
position pipe welding?
A. 3G and
4G
B. 2G and
5G
C. 3G and
1G
D. 4G and 5G -
ANSWER-B
,What ASME Code Section has welding electrode storage
requirements?
A. ASME IX
B. ASME VIII
C. ASME B31.1
D. ASME II Part C - ANSWER-D
What are the number of transverse guided bend tests required
for Performance
Qualification in a 6G
position?
A. 2
B. 4
C.
6
D. 3 -
ANSWER-B
May a GMAW, short circuit transfer, welding procedure be
qualified using real-time ultrasonic?
A. Yes
B. No
C. Not enough information given
D. Yes, provided bend tests are done - ANSWER-B
Three arc welding processes are:
A. BMAW, SMAW, EFGAW
B. FCAW, SAW, ESW
,C. SMAW, GTAW, PAW
D. PTAW, SLAW, PEAW - ANSWER-C
You are reviewing a WPQ (QW-484) for a welder testing in
the 2-G position; (TS-60,000 psi). The test results indicate
the following: on SA-53 grade B pipe
#1 Tensile developed 51,000 psi, broke in the weld
#2 Tensile developed 56,900 psi, broke in base metal
#1 Transverse root bend
satisfactory #2Transverse face
bend satisfactory Will these test
qualify the welder?
A. Yes
B. No
C. Not enough information given
D. Tension test is acceptable but #1 is unacceptable - ANSWER-
A
Is a welding procedure qualified under the 1965 ASME Code
Section IX still
applicable?
A. Yes
B. No, must be
requalified
C. Is only applicable for 1965 pressure
vessels
D. Cannot be used for new construction - repairs only
- ANSWER-A
, A nonessential variable must be
documented on:
A. The
WPQ
B. The
PQR
C. The
WPS
D. All of the above - ANSWER-C
What are the various positions in which a welder may qualify
for plate groove welds? A. 1G
B. 3G
C. 4G
D. All of the above - ANSWER-D
A welder was qualified with a P-1 test coupon using SMAW
E7018 electrodes. May the welder weld P-4 material using
E8028 electrodes in production?
(Assume the P-4 procedure using E8028 electrodes has been
qualified.)
A. Yes
B. No
C. Not enough information provided
D. None of the above - ANSWER-A
What are the primary classifications of guided-bend tests
permitted by the
WELDING, BRAZING, AND FUSING || MOST RECENT
EXAM 2026|2027 ACTUAL COMPLETE REAL EXAM
QUESTIONS AND CORRECT ANSWERS (VERIFIED
ANSWERS) ALREADY GRADED A+ | GUARANTEED
SUCCESS!! NEWEST EXAM | JUST RELEASED!!
A repair organization has a WPS which states it is qualified for
P-8 to P-8 material welded with either E308, E308L, E309, E316,
electrodes (SMAW process). The PQR, supporting this WPS,
states the weld test coupons were SA-240 Type 304L material,
welded with E308 electrodes. Is the WPS properly qualified for
the base material listed?
A. Yes
B. No
C. Not enough information given
D. Yes, if properly heat treated - ANSWER-A
What positions are necessary to qualify a welder for all
position pipe welding?
A. 3G and
4G
B. 2G and
5G
C. 3G and
1G
D. 4G and 5G -
ANSWER-B
,What ASME Code Section has welding electrode storage
requirements?
A. ASME IX
B. ASME VIII
C. ASME B31.1
D. ASME II Part C - ANSWER-D
What are the number of transverse guided bend tests required
for Performance
Qualification in a 6G
position?
A. 2
B. 4
C.
6
D. 3 -
ANSWER-B
May a GMAW, short circuit transfer, welding procedure be
qualified using real-time ultrasonic?
A. Yes
B. No
C. Not enough information given
D. Yes, provided bend tests are done - ANSWER-B
Three arc welding processes are:
A. BMAW, SMAW, EFGAW
B. FCAW, SAW, ESW
,C. SMAW, GTAW, PAW
D. PTAW, SLAW, PEAW - ANSWER-C
You are reviewing a WPQ (QW-484) for a welder testing in
the 2-G position; (TS-60,000 psi). The test results indicate
the following: on SA-53 grade B pipe
#1 Tensile developed 51,000 psi, broke in the weld
#2 Tensile developed 56,900 psi, broke in base metal
#1 Transverse root bend
satisfactory #2Transverse face
bend satisfactory Will these test
qualify the welder?
A. Yes
B. No
C. Not enough information given
D. Tension test is acceptable but #1 is unacceptable - ANSWER-
A
Is a welding procedure qualified under the 1965 ASME Code
Section IX still
applicable?
A. Yes
B. No, must be
requalified
C. Is only applicable for 1965 pressure
vessels
D. Cannot be used for new construction - repairs only
- ANSWER-A
, A nonessential variable must be
documented on:
A. The
WPQ
B. The
PQR
C. The
WPS
D. All of the above - ANSWER-C
What are the various positions in which a welder may qualify
for plate groove welds? A. 1G
B. 3G
C. 4G
D. All of the above - ANSWER-D
A welder was qualified with a P-1 test coupon using SMAW
E7018 electrodes. May the welder weld P-4 material using
E8028 electrodes in production?
(Assume the P-4 procedure using E8028 electrodes has been
qualified.)
A. Yes
B. No
C. Not enough information provided
D. None of the above - ANSWER-A
What are the primary classifications of guided-bend tests
permitted by the
