MICHIGAN STATE BRAKES CERTIFICATION EXAM LATEST 2026
UPDATED QUESTIONS AND VERIFIED 100% SOLUTIONS
(2026/2027) GRADE: A+|STATUS: GUARANTEED PASS
The brake warning light on the dash stays on all the time, which of the following could be the
cause of the problem? - Answers -A problem in the hydraulic circuit
Which of the following would be the LEAST likely cause for an intermittent problem in an ABS
system? - Answers -Open wheel sensor circuit
The brake lights on a car do not light when the brake pedal is depressed, which of the following
is the LEAST likely cause of the problem? - Answers -A burned out bulb.
Which of the following incorrect service procedures could cause brake pedal pulsation? -
Answers -incorrect run-out on the car brake lathe
What type of rotor surface provides the best braking with new pads? - Answers -A smooth, flat
surface
which of the following is a quick way to isolated a defective master cylinder? There are no
external leaks in the system. - Answers -pump up the brake pedal, then hold it firm. if the pedal
slowly drops to the floor, the master cylinder may be defective.
1|Page
, A common cause of pedal pulsation during brake application is: - Answers -NOT caused by
improperly torqued wheels, damaged backing plates, or lubricated shims
the car is at reset. When you slowly apply the brake pedal you hear a squeaking noise at the
rear of the vehicle. what could cause this noise? - Answers -dry backing plate contact surfaces
While test driving a car, the mechanic finds that the right front brake "grabs". The most likely
cause of this problem is: - Answers -brake fluid or grease on the brake linings
Wheel speed sensors: - Answers -send an A/C signal to the control module
Which of the following incorrect service procedures will cause brake lock up? - Answers -Master
Cylinder push rod adjusted too long
During a road test, you find that when normal breaking pressure is applied the pedal slowly
goes to the floor. What is the likely cause of this problem? - Answers -A leaking master cylinder
primary piston seal.
Before replacing a hydralic brake hose on an ABS equipped vehicle, you should first: - Answers -
relieve brake system pressure according to manufacturer procedures
2|Page
UPDATED QUESTIONS AND VERIFIED 100% SOLUTIONS
(2026/2027) GRADE: A+|STATUS: GUARANTEED PASS
The brake warning light on the dash stays on all the time, which of the following could be the
cause of the problem? - Answers -A problem in the hydraulic circuit
Which of the following would be the LEAST likely cause for an intermittent problem in an ABS
system? - Answers -Open wheel sensor circuit
The brake lights on a car do not light when the brake pedal is depressed, which of the following
is the LEAST likely cause of the problem? - Answers -A burned out bulb.
Which of the following incorrect service procedures could cause brake pedal pulsation? -
Answers -incorrect run-out on the car brake lathe
What type of rotor surface provides the best braking with new pads? - Answers -A smooth, flat
surface
which of the following is a quick way to isolated a defective master cylinder? There are no
external leaks in the system. - Answers -pump up the brake pedal, then hold it firm. if the pedal
slowly drops to the floor, the master cylinder may be defective.
1|Page
, A common cause of pedal pulsation during brake application is: - Answers -NOT caused by
improperly torqued wheels, damaged backing plates, or lubricated shims
the car is at reset. When you slowly apply the brake pedal you hear a squeaking noise at the
rear of the vehicle. what could cause this noise? - Answers -dry backing plate contact surfaces
While test driving a car, the mechanic finds that the right front brake "grabs". The most likely
cause of this problem is: - Answers -brake fluid or grease on the brake linings
Wheel speed sensors: - Answers -send an A/C signal to the control module
Which of the following incorrect service procedures will cause brake lock up? - Answers -Master
Cylinder push rod adjusted too long
During a road test, you find that when normal breaking pressure is applied the pedal slowly
goes to the floor. What is the likely cause of this problem? - Answers -A leaking master cylinder
primary piston seal.
Before replacing a hydralic brake hose on an ABS equipped vehicle, you should first: - Answers -
relieve brake system pressure according to manufacturer procedures
2|Page
