DANTE LEVEL 1 ACTUAL EXAM QUESTIONS WITH COMPLETE
SOLUTION GUIDE (A+ GRADED 100% VERIFIED) LATEST
VERSION 2026/2027!!
Question 1
What is the maximum cable length recommended for standard CAT5e
or CAT6 Ethernet cable in a Dante network without using fiber optic or
repeaters?
A) 50 meters
B) 100 meters
C) 200 meters
D) 500 meters
Correct Answer: B) 100 meters
Rationale: The IEEE 802.3 standard specifies a maximum cable length of
100 meters for twisted-pair Ethernet copper cabling (CAT5e/CAT6) to
maintain signal integrity and reliable data transmission.
Question 2
What protocol does Dante use for audio clock synchronization across
the network?
A) NTP (Network Time Protocol)
B) SNTP (Simple Network Time Protocol)
C) PTP (Precision Time Protocol) IEEE 1588
D) RTP (Real-time Transport Protocol)
Correct Answer: C) PTP (Precision Time Protocol) IEEE 1588
Rationale: Dante uses PTP (IEEE 1588) to provide highly accurate clock
,synchronization, ensuring all devices sample at the same rate and
maintain phase alignment with sub-microsecond precision.
Question 3
What is the primary function of a Dante-enabled device's "Latency"
setting?
A) To adjust the sample rate of the audio stream
B) To determine the amount of time the receiver will wait for incoming
audio packets before playing them out
C) To control the volume level of the audio output
D) To set the priority of the audio stream on the network
Correct Answer: B) To determine the amount of time the receiver will
wait for incoming audio packets before playing them out
Rationale: Latency settings in Dante devices create a buffer that allows
packets to arrive out of order or be delayed by network switches
without causing audio dropouts. The receiver waits for the specified
latency period before playing out the audio.
Question 4
When configuring Dante Controller for the first time on a computer,
what network requirement must be met?
A) The computer must have a static IP address
B) The computer must be on the same subnet as the Dante devices
C) The computer must have a dedicated Dante network card
D) The computer must be connected directly to the Dante network
without any switches
Correct Answer: B) The computer must be on the same subnet as the
,Dante devices
Rationale: Dante Controller uses IP multicast discovery protocols. For
the software to discover devices, the computer running Dante
Controller must have an IP address within the same subnet range as the
Dante devices.
Question 5
What is the maximum number of audio channels that can be
transmitted on a single Dante network with 1 Gigabit Ethernet?
A) 64 channels at 48kHz
B) 128 channels at 48kHz
C) 512 channels at 48kHz
D) 1024 channels at 48kHz
Correct Answer: C) 512 channels at 48kHz
Rationale: Dante transmits audio as uncompressed PCM over IP. With a
1 Gigabit Ethernet network, the practical limit is approximately 512
channels at 48kHz sample rate with a 24-bit word length.
Question 6
What does the color red indicate in the Dante Controller's Clock Status
display?
A) The device is the Grand Master clock
B) The device is not receiving clock synchronization
C) The device is a Slave clock
D) The device is in power-saving mode
Correct Answer: B) The device is not receiving clock synchronization
Rationale: Red color in the Clock Status indicates that the device is not
, receiving PTP synchronization from any master clock, meaning it is not
locked to the network's clock and may not pass audio properly.
Question 7
Which of the following is NOT a valid Dante audio routing subscription
type?
A) Unicast
B) Multicast
C) Broadcast
D) Direct
Correct Answer: C) Broadcast
Rationale: Dante supports unicast (one transmitter to one receiver) and
multicast (one transmitter to multiple receivers) subscriptions.
Broadcast is not a valid subscription type in Dante as it would flood the
network with unnecessary data.
Question 8
What happens when a Dante device is powered on with a sample rate
that does not match the rest of the Dante network?
A) The device will automatically change its sample rate to match the
network
B) The device will not be visible in Dante Controller
C) The device will appear in Dante Controller but subscriptions will fail
D) The device will function normally but with reduced audio quality
Correct Answer: C) The device will appear in Dante Controller but
subscriptions will fail
Rationale: Dante devices must operate at the same sample rate to
SOLUTION GUIDE (A+ GRADED 100% VERIFIED) LATEST
VERSION 2026/2027!!
Question 1
What is the maximum cable length recommended for standard CAT5e
or CAT6 Ethernet cable in a Dante network without using fiber optic or
repeaters?
A) 50 meters
B) 100 meters
C) 200 meters
D) 500 meters
Correct Answer: B) 100 meters
Rationale: The IEEE 802.3 standard specifies a maximum cable length of
100 meters for twisted-pair Ethernet copper cabling (CAT5e/CAT6) to
maintain signal integrity and reliable data transmission.
Question 2
What protocol does Dante use for audio clock synchronization across
the network?
A) NTP (Network Time Protocol)
B) SNTP (Simple Network Time Protocol)
C) PTP (Precision Time Protocol) IEEE 1588
D) RTP (Real-time Transport Protocol)
Correct Answer: C) PTP (Precision Time Protocol) IEEE 1588
Rationale: Dante uses PTP (IEEE 1588) to provide highly accurate clock
,synchronization, ensuring all devices sample at the same rate and
maintain phase alignment with sub-microsecond precision.
Question 3
What is the primary function of a Dante-enabled device's "Latency"
setting?
A) To adjust the sample rate of the audio stream
B) To determine the amount of time the receiver will wait for incoming
audio packets before playing them out
C) To control the volume level of the audio output
D) To set the priority of the audio stream on the network
Correct Answer: B) To determine the amount of time the receiver will
wait for incoming audio packets before playing them out
Rationale: Latency settings in Dante devices create a buffer that allows
packets to arrive out of order or be delayed by network switches
without causing audio dropouts. The receiver waits for the specified
latency period before playing out the audio.
Question 4
When configuring Dante Controller for the first time on a computer,
what network requirement must be met?
A) The computer must have a static IP address
B) The computer must be on the same subnet as the Dante devices
C) The computer must have a dedicated Dante network card
D) The computer must be connected directly to the Dante network
without any switches
Correct Answer: B) The computer must be on the same subnet as the
,Dante devices
Rationale: Dante Controller uses IP multicast discovery protocols. For
the software to discover devices, the computer running Dante
Controller must have an IP address within the same subnet range as the
Dante devices.
Question 5
What is the maximum number of audio channels that can be
transmitted on a single Dante network with 1 Gigabit Ethernet?
A) 64 channels at 48kHz
B) 128 channels at 48kHz
C) 512 channels at 48kHz
D) 1024 channels at 48kHz
Correct Answer: C) 512 channels at 48kHz
Rationale: Dante transmits audio as uncompressed PCM over IP. With a
1 Gigabit Ethernet network, the practical limit is approximately 512
channels at 48kHz sample rate with a 24-bit word length.
Question 6
What does the color red indicate in the Dante Controller's Clock Status
display?
A) The device is the Grand Master clock
B) The device is not receiving clock synchronization
C) The device is a Slave clock
D) The device is in power-saving mode
Correct Answer: B) The device is not receiving clock synchronization
Rationale: Red color in the Clock Status indicates that the device is not
, receiving PTP synchronization from any master clock, meaning it is not
locked to the network's clock and may not pass audio properly.
Question 7
Which of the following is NOT a valid Dante audio routing subscription
type?
A) Unicast
B) Multicast
C) Broadcast
D) Direct
Correct Answer: C) Broadcast
Rationale: Dante supports unicast (one transmitter to one receiver) and
multicast (one transmitter to multiple receivers) subscriptions.
Broadcast is not a valid subscription type in Dante as it would flood the
network with unnecessary data.
Question 8
What happens when a Dante device is powered on with a sample rate
that does not match the rest of the Dante network?
A) The device will automatically change its sample rate to match the
network
B) The device will not be visible in Dante Controller
C) The device will appear in Dante Controller but subscriptions will fail
D) The device will function normally but with reduced audio quality
Correct Answer: C) The device will appear in Dante Controller but
subscriptions will fail
Rationale: Dante devices must operate at the same sample rate to
