MICHIGAN STATE BRAKES CERTIFICATION
EXAM ACTUAL EXAM 2026 | QUESTIONS
MERGED WITH CORRECT COMPLETE
SOLUTIONS || ALREADY GRADED A+ ||
2026-2027 LATEST UPDATE!!!
Most 1995 & newer vehicles use which of the following types of
wheels bearings on non-drive wheel? - ANSWER-Sealed non-
serviceable
to test a vacuum power brake booster in the vehicle, you should pump
the brake pedal at least 4 times, hold the brake pedal depressed, and
start the engine. the brake pedal should: - ANSWER-drop slightly and
remain firm
You are installing a set of brake shoe linings that are not the same
length. Traditionally, the primary shoe lining is: - ANSWER-Smaller and
goes towards the front of the car.
, A cracked or torn vacuum diaphragm in a brake power booster would
most likely cause: - ANSWER-a hard pedal feel requiring very high
pedal effort to stop
A mechanic finds gear lube inside both rear brake drums on a rear-
wheel-drive vehicle. What is the most likely cause of this problem? -
ANSWER-A plugged axle
Which of the following incorrect service procedures will cause brake
lock-up? - ANSWER-master cylinder push rod adjusted too long
Which of the following describes the proper way to depressurized an
ABS system? - ANSWER-Pump the brake pedal at least 25 times (or
more, depending on the manufacturer's recommendation) with the
ignition off.
The rear brakes are dragging after having new linings installed and the
drums machined. the most likely cause is the: - ANSWER-technician
use the parking brake to adjust shoes and the cable is stuck
When turning brake drums: - ANSWER-use a dampening strap to
reduce chatter
Which of the following is NOT a necessary drum brake measurement?
- ANSWER-run-out
On a 3-channel system, which wheels are on the same circuit? -
ANSWER-both rear wheels
One way to test an ABS wheel speed signal is to use _____ on your
digital multimeter. - ANSWER-AC volts
The key input for the ABS control module comes from the: - ANSWER-
wheel speed sensors
EXAM ACTUAL EXAM 2026 | QUESTIONS
MERGED WITH CORRECT COMPLETE
SOLUTIONS || ALREADY GRADED A+ ||
2026-2027 LATEST UPDATE!!!
Most 1995 & newer vehicles use which of the following types of
wheels bearings on non-drive wheel? - ANSWER-Sealed non-
serviceable
to test a vacuum power brake booster in the vehicle, you should pump
the brake pedal at least 4 times, hold the brake pedal depressed, and
start the engine. the brake pedal should: - ANSWER-drop slightly and
remain firm
You are installing a set of brake shoe linings that are not the same
length. Traditionally, the primary shoe lining is: - ANSWER-Smaller and
goes towards the front of the car.
, A cracked or torn vacuum diaphragm in a brake power booster would
most likely cause: - ANSWER-a hard pedal feel requiring very high
pedal effort to stop
A mechanic finds gear lube inside both rear brake drums on a rear-
wheel-drive vehicle. What is the most likely cause of this problem? -
ANSWER-A plugged axle
Which of the following incorrect service procedures will cause brake
lock-up? - ANSWER-master cylinder push rod adjusted too long
Which of the following describes the proper way to depressurized an
ABS system? - ANSWER-Pump the brake pedal at least 25 times (or
more, depending on the manufacturer's recommendation) with the
ignition off.
The rear brakes are dragging after having new linings installed and the
drums machined. the most likely cause is the: - ANSWER-technician
use the parking brake to adjust shoes and the cable is stuck
When turning brake drums: - ANSWER-use a dampening strap to
reduce chatter
Which of the following is NOT a necessary drum brake measurement?
- ANSWER-run-out
On a 3-channel system, which wheels are on the same circuit? -
ANSWER-both rear wheels
One way to test an ABS wheel speed signal is to use _____ on your
digital multimeter. - ANSWER-AC volts
The key input for the ABS control module comes from the: - ANSWER-
wheel speed sensors
