1|Page
ICC BOLTING EXAM NEWEST 2026/2027 ACTUAL EXAM
COMPLETE 150 QUESTIONS AND CORRECT DETAILED
ANSWERS (VERIFIED ANSWERS) |ALREADY GRADED A+||JUST
OUT!!!
According to the Code of Standard Practice for Steel Buildings
and Bridges, the permitted method of applying shop paint is: -
ANSWER-Brushing, Rolling, or spraying - Section 6.5.3 - Code of
Standard Practice for Steel Buildings and Bridges
According to the Code of Standard Practice for Steel Buildings
and Bridges, the "BLANK" is responsible for the temporary
vertical and lateral supports necessary for the erection of the
building framework. - ANSWER-Steel erection contractor -
Section 7.10.3 - Code of Standard Practice for Steel Buildings
and Bridges
Which section of the Code of Standard Practice for Steel
Buildings and Bridges includes the permitted tolerances for
detailed erection? - ANSWER-Section 7.13 - Code of Standard
Practice for Steel Buildings and Bridges
According to the Code of Standard Practice for Steel Buildings
and Bridges, "BLANK" are allowed in moderate amounts for
correction of errors during steel framing erection. - ANSWER-
,2|Page
drift pins, grinding, and reaming. - Section 7.14 - Code of
Standard Practice for Steel Buildings and Bridges
According to the Code of Standard Practice for Steel Buildings
and Bridges, what types of openings for other trades are
allowed to be cut in the structural steel? - ANSWER-Only those
openings shown on the contract document drawings and
specifications. - Section 7.15 - Code of Standard Practice for
Steel Buildings and Bridges
According to the AISC Steel Construction Manual, what should
be done if grouting is delayed on a base plate supported by
leveling nuts until after steel erection? - ANSWER-Use steel
shims to support the base plate. Page 14-7, Part 14, AISC Steel
Construction Manual
According to the AISC Steel Construction Manual, the
recommended maximum size of anchor rod hole in a base plate
for a 1 inch diameter anchor rod is "BLANK" inches. - ANSWER-
1-13/16 inches - Table 14-2, Part 14, AISC Steel Construction
Manual
According to the AISC Steel Construction Manual, the minimum
washer thickness for a base plate anchor rod 1 inch diameter is
, 3|Page
"BLANK" inches. - ANSWER-⅜ inch - Table 14-2, Part 14, AISC
Steel Construction Manual
According to the Code of Standard Practice for Steel Buildings
and Bridges, who is responsible for the accurate location and
strength of the foundation piers for the base plates? - ANSWER-
owners designated representative for construction - Section 7.3
- Code of Standard Practice for Steel Buildings and Bridges
According to the Code of Standard Practice for Steel Buildings
and Bridges, who is responsible for the correct setting of the
anchor rods for the base plates? - ANSWER-owners designated
representative for construction - Section 7.5.1 - owners
designated representative for construction
According to the IBC, the "blank" is to hire the special inspector.
- ANSWER-owner or owners agent. 2009 IBC Section 1704.1
According to the IBC, the "blank" is the responsible for the
approval of a person's qualifications to act as a special
inspector. - ANSWER-code official. 2009 IBC, Section 1704.1
According to the IBC, discrepancy corrections are made known
to the building official by: - ANSWER-final report. 2009 IBC,
Section1704.1.2
ICC BOLTING EXAM NEWEST 2026/2027 ACTUAL EXAM
COMPLETE 150 QUESTIONS AND CORRECT DETAILED
ANSWERS (VERIFIED ANSWERS) |ALREADY GRADED A+||JUST
OUT!!!
According to the Code of Standard Practice for Steel Buildings
and Bridges, the permitted method of applying shop paint is: -
ANSWER-Brushing, Rolling, or spraying - Section 6.5.3 - Code of
Standard Practice for Steel Buildings and Bridges
According to the Code of Standard Practice for Steel Buildings
and Bridges, the "BLANK" is responsible for the temporary
vertical and lateral supports necessary for the erection of the
building framework. - ANSWER-Steel erection contractor -
Section 7.10.3 - Code of Standard Practice for Steel Buildings
and Bridges
Which section of the Code of Standard Practice for Steel
Buildings and Bridges includes the permitted tolerances for
detailed erection? - ANSWER-Section 7.13 - Code of Standard
Practice for Steel Buildings and Bridges
According to the Code of Standard Practice for Steel Buildings
and Bridges, "BLANK" are allowed in moderate amounts for
correction of errors during steel framing erection. - ANSWER-
,2|Page
drift pins, grinding, and reaming. - Section 7.14 - Code of
Standard Practice for Steel Buildings and Bridges
According to the Code of Standard Practice for Steel Buildings
and Bridges, what types of openings for other trades are
allowed to be cut in the structural steel? - ANSWER-Only those
openings shown on the contract document drawings and
specifications. - Section 7.15 - Code of Standard Practice for
Steel Buildings and Bridges
According to the AISC Steel Construction Manual, what should
be done if grouting is delayed on a base plate supported by
leveling nuts until after steel erection? - ANSWER-Use steel
shims to support the base plate. Page 14-7, Part 14, AISC Steel
Construction Manual
According to the AISC Steel Construction Manual, the
recommended maximum size of anchor rod hole in a base plate
for a 1 inch diameter anchor rod is "BLANK" inches. - ANSWER-
1-13/16 inches - Table 14-2, Part 14, AISC Steel Construction
Manual
According to the AISC Steel Construction Manual, the minimum
washer thickness for a base plate anchor rod 1 inch diameter is
, 3|Page
"BLANK" inches. - ANSWER-⅜ inch - Table 14-2, Part 14, AISC
Steel Construction Manual
According to the Code of Standard Practice for Steel Buildings
and Bridges, who is responsible for the accurate location and
strength of the foundation piers for the base plates? - ANSWER-
owners designated representative for construction - Section 7.3
- Code of Standard Practice for Steel Buildings and Bridges
According to the Code of Standard Practice for Steel Buildings
and Bridges, who is responsible for the correct setting of the
anchor rods for the base plates? - ANSWER-owners designated
representative for construction - Section 7.5.1 - owners
designated representative for construction
According to the IBC, the "blank" is to hire the special inspector.
- ANSWER-owner or owners agent. 2009 IBC Section 1704.1
According to the IBC, the "blank" is the responsible for the
approval of a person's qualifications to act as a special
inspector. - ANSWER-code official. 2009 IBC, Section 1704.1
According to the IBC, discrepancy corrections are made known
to the building official by: - ANSWER-final report. 2009 IBC,
Section1704.1.2
