UTAH B100 2026 Exam Review
How far off can a truss be on a bearing header from the 1/4 inch
plans?
According to OSHA, a trench that reaches a depth of 4 25
feet shall be supplied witha ladder or a means of egress.
The maximum lateral distance a person shall travel to
reach this ladder shall not exceed (blank) feet
According to OSHA, all of the following power tools must circular saw
be equipped with only a positive on/off switch except:
The maximum space between reinforcing bars in a slab or 3 times
wall should be no greater than how many times the
thickness of the concrete slab or wall?
According to the code, how should you attach a floor joist 3 8d nails or 3- 3 inch staples
to a sole plate?
How wide should the footing be for a conventional light- 12 inches
frame construction 2 story building with load bearing soil
value of 2,000 PSI?
According to OSHA, at what height must a 4 foot wide 26 feet
scaffold be tied off to the building?
What forms are used in elevators and silos? slip forms
The maximum glass allowed in a 1 hour fire rated door is: 100 square inches per door with no side less than 4 inches
How should an upper wall cabinet be installed next to a check to see that the wall is plumb and corner is square
wall?
What is an advantage of repairing asphalt shingles during asphalt shingles become more pliable as they are warmed
warm weather?
What is the nail spacing required on wood soffit? 6 inches
How often are strength tests required for concrete? at least 1 a day per 150 cubic yards or 5,000 square feet
Who designs scaffolds to OSHA specifications? engineer
What is the minimum spacing between block and rebar 1/4 inch
when grouting with coarse grout in a hollow masonry unit?
, UTAH B100 2026 Exam Review
What is the minimum size of metal in aluminum flashing? .024 inches
What method should be used to unload steel beams with a use a spreader bar and cables
crane?
What is the usual cause for concrete cracking on the overworking the dry surface
surface?
How long before digging should you notify the local 2 days
marking company?
What advantage does nuclear compaction have on a it does not require the removal of soil samples from the site of the test
jobsite?
After tensioning both ends of a tendon in a form, what 12 inches
minimum length of tendon should be left exposed?
You have a sloped lot with the high point at 28 inches and cut from the high point and add to to the low pointq
the low elevation at 26.4, what is the preferred way to level
the lot?
If a building is at the bottom of a hill that has a 1:1 slope, 15 feet
what is the maximum distance the building need not
exceed from the toe of the hill?
Welded wire mesh is to be installed in concrete where? held to the top of the concrete to reduce surface cracks
What is the minimum height between finish floor and joists 7 feet
in a kitchen with joists at 48 inches on center?
What is the maximum span of a 2 x 6 purlin? 6 feet
When an onsite wastewater tank has been abandoned, 30 days
how many days do you have before it must be removed
from the ground?
How are the ends of bottom bearing joists normally solid blocking
restrained?
What grading operation requires the most operator skill? finish grading
What is the thickness of standard glass masonry units? 3 7/8 inches
, UTAH B100 2026 Exam Review
Blue stake: what size marking strip needs to be used when 1 inch x 18 inches
laying foundations or marking utilities?
Where is the most common place to have a roof leak? wall to roof connection
What type of power tool requires specific training of powder actuated
operators before they are allowed to operate?
What is the proper distance of the moulding from the floor? 1/4 inch above the subfloor
Which type of hydrated lime is best to use in mortar for type S
heavy bearing?
At what stage of the construction process would the builder after the wall has been erected
cut out the sole plate in a door opening?
How should the flange of a CMU be placed in a wall? wide flange on the top
Which of the following shall not be assumed to have organic silt
presumptive load bearing capacity for foundations?
What is the minimum allowable width of a glass block at a 3 inches
mortar joint?
What can be done to avoid the problem of reverse add additional bars
curvature in a post tensioned beam tendon?
What is the proper way to cover nails in drywall? ready mix compound
What distance from the edge of a roof can materials and 6 feet
equipment be placed if not guardrails are present?
According to OSHA rules and regulations, scaffold planks 6
should extend past their end supports a minimum of
(blank) inches
What is the minimum concrete PSI that is required for 2500 PSI
basement walls or slabs not exposed to weather?
What type of aggregate should be used to allow the rounded, such as river gravel
concrete to pump more easily?
How far off can a truss be on a bearing header from the 1/4 inch
plans?
According to OSHA, a trench that reaches a depth of 4 25
feet shall be supplied witha ladder or a means of egress.
The maximum lateral distance a person shall travel to
reach this ladder shall not exceed (blank) feet
According to OSHA, all of the following power tools must circular saw
be equipped with only a positive on/off switch except:
The maximum space between reinforcing bars in a slab or 3 times
wall should be no greater than how many times the
thickness of the concrete slab or wall?
According to the code, how should you attach a floor joist 3 8d nails or 3- 3 inch staples
to a sole plate?
How wide should the footing be for a conventional light- 12 inches
frame construction 2 story building with load bearing soil
value of 2,000 PSI?
According to OSHA, at what height must a 4 foot wide 26 feet
scaffold be tied off to the building?
What forms are used in elevators and silos? slip forms
The maximum glass allowed in a 1 hour fire rated door is: 100 square inches per door with no side less than 4 inches
How should an upper wall cabinet be installed next to a check to see that the wall is plumb and corner is square
wall?
What is an advantage of repairing asphalt shingles during asphalt shingles become more pliable as they are warmed
warm weather?
What is the nail spacing required on wood soffit? 6 inches
How often are strength tests required for concrete? at least 1 a day per 150 cubic yards or 5,000 square feet
Who designs scaffolds to OSHA specifications? engineer
What is the minimum spacing between block and rebar 1/4 inch
when grouting with coarse grout in a hollow masonry unit?
, UTAH B100 2026 Exam Review
What is the minimum size of metal in aluminum flashing? .024 inches
What method should be used to unload steel beams with a use a spreader bar and cables
crane?
What is the usual cause for concrete cracking on the overworking the dry surface
surface?
How long before digging should you notify the local 2 days
marking company?
What advantage does nuclear compaction have on a it does not require the removal of soil samples from the site of the test
jobsite?
After tensioning both ends of a tendon in a form, what 12 inches
minimum length of tendon should be left exposed?
You have a sloped lot with the high point at 28 inches and cut from the high point and add to to the low pointq
the low elevation at 26.4, what is the preferred way to level
the lot?
If a building is at the bottom of a hill that has a 1:1 slope, 15 feet
what is the maximum distance the building need not
exceed from the toe of the hill?
Welded wire mesh is to be installed in concrete where? held to the top of the concrete to reduce surface cracks
What is the minimum height between finish floor and joists 7 feet
in a kitchen with joists at 48 inches on center?
What is the maximum span of a 2 x 6 purlin? 6 feet
When an onsite wastewater tank has been abandoned, 30 days
how many days do you have before it must be removed
from the ground?
How are the ends of bottom bearing joists normally solid blocking
restrained?
What grading operation requires the most operator skill? finish grading
What is the thickness of standard glass masonry units? 3 7/8 inches
, UTAH B100 2026 Exam Review
Blue stake: what size marking strip needs to be used when 1 inch x 18 inches
laying foundations or marking utilities?
Where is the most common place to have a roof leak? wall to roof connection
What type of power tool requires specific training of powder actuated
operators before they are allowed to operate?
What is the proper distance of the moulding from the floor? 1/4 inch above the subfloor
Which type of hydrated lime is best to use in mortar for type S
heavy bearing?
At what stage of the construction process would the builder after the wall has been erected
cut out the sole plate in a door opening?
How should the flange of a CMU be placed in a wall? wide flange on the top
Which of the following shall not be assumed to have organic silt
presumptive load bearing capacity for foundations?
What is the minimum allowable width of a glass block at a 3 inches
mortar joint?
What can be done to avoid the problem of reverse add additional bars
curvature in a post tensioned beam tendon?
What is the proper way to cover nails in drywall? ready mix compound
What distance from the edge of a roof can materials and 6 feet
equipment be placed if not guardrails are present?
According to OSHA rules and regulations, scaffold planks 6
should extend past their end supports a minimum of
(blank) inches
What is the minimum concrete PSI that is required for 2500 PSI
basement walls or slabs not exposed to weather?
What type of aggregate should be used to allow the rounded, such as river gravel
concrete to pump more easily?
