AFAB 110 Final
Study online at https://quizlet.com/_jqpmhh
1. The word print can best be used the same as the word Drawing
_____________
2. In many cases, the print is also an important part of a Contract
_______________ in the industrial setting.
3. The study of print reading is closely related to the study Drafting
of _____________, the general term for creating drawings
of objects in technical fields.
4. PDF is an electronic file format that allows the user Portable Document For-
to share a drawing or image without giving them the mat
actual CAD data file. PDF stands for __________________.
5. A voluntary guideline that establishes the method of Standard
representation for prints, as well as other engineering
practices, is a ________________.
6. Identify the line below that is fictitious. Dotted line
7. Cutting-plane lines are easily identifiable due to the Arrowhead
appearance of a(n) ___________ on each end of the line.
8. Identify the line below that is to be drawn thick. Cutting-plane line
9. The standardized list of line types, perhaps in the Alphabet of line
form of a chart, is defined in many references as the
________________.
10. Print reading is the process of analyzing a print to Interpretation
obtain information. This task involves two principal
elements: visualization and _____________.
11. 8
1/9
, AFAB 110 Final
Study online at https://quizlet.com/_jqpmhh
If a D-size sheet of paper is properly cut, how many
A-size sheets should result?
12. For which of the following is least likely to be found on Finish
a basic parts list?
13. A block that is important to read in the early stage of Revision history
examining a print is the ___________ block, which helps
determine if the print being observed is up-to-date.
14. Which of the following is least likely to be found on a Finish
basic parts list?
15. The word that basically means "cut in half" is Bisect
_______________.
16. If a hexagon is inscribed within a circle, the diameter Across-the-corners
of the circle is equivalent to the term __________.
17. In most CAD systems, the basic geometric forms Primitives
used to create complex models are referred to as
_______________.
18. As lines are parallel to each other, arcs are Concentric
________________ to each other.
19. Which of the following is a way to describe the point of Found on a line connect-
tangency between two circles? ing the two center points
20. Which of the following cannot be defined by the way a Ogee curve
plane intersects a cone?
21. Which of the following is not an example of a spatial Playing 3D tic-tac-toe
visualization instrument?
2/9
Study online at https://quizlet.com/_jqpmhh
1. The word print can best be used the same as the word Drawing
_____________
2. In many cases, the print is also an important part of a Contract
_______________ in the industrial setting.
3. The study of print reading is closely related to the study Drafting
of _____________, the general term for creating drawings
of objects in technical fields.
4. PDF is an electronic file format that allows the user Portable Document For-
to share a drawing or image without giving them the mat
actual CAD data file. PDF stands for __________________.
5. A voluntary guideline that establishes the method of Standard
representation for prints, as well as other engineering
practices, is a ________________.
6. Identify the line below that is fictitious. Dotted line
7. Cutting-plane lines are easily identifiable due to the Arrowhead
appearance of a(n) ___________ on each end of the line.
8. Identify the line below that is to be drawn thick. Cutting-plane line
9. The standardized list of line types, perhaps in the Alphabet of line
form of a chart, is defined in many references as the
________________.
10. Print reading is the process of analyzing a print to Interpretation
obtain information. This task involves two principal
elements: visualization and _____________.
11. 8
1/9
, AFAB 110 Final
Study online at https://quizlet.com/_jqpmhh
If a D-size sheet of paper is properly cut, how many
A-size sheets should result?
12. For which of the following is least likely to be found on Finish
a basic parts list?
13. A block that is important to read in the early stage of Revision history
examining a print is the ___________ block, which helps
determine if the print being observed is up-to-date.
14. Which of the following is least likely to be found on a Finish
basic parts list?
15. The word that basically means "cut in half" is Bisect
_______________.
16. If a hexagon is inscribed within a circle, the diameter Across-the-corners
of the circle is equivalent to the term __________.
17. In most CAD systems, the basic geometric forms Primitives
used to create complex models are referred to as
_______________.
18. As lines are parallel to each other, arcs are Concentric
________________ to each other.
19. Which of the following is a way to describe the point of Found on a line connect-
tangency between two circles? ing the two center points
20. Which of the following cannot be defined by the way a Ogee curve
plane intersects a cone?
21. Which of the following is not an example of a spatial Playing 3D tic-tac-toe
visualization instrument?
2/9
