NCCER MILLWRIGHT PRACTICE EXAM 2
unusual If the seal was not properly aligned or there is excessive wear in some bearing
or shaft,_______ wear tracks will be the indicator
sharpened brass putty knife For removing hard to remove gasket materials found on sealing surfaces, ______
is recommended
Conducted on the job Apprenticeship training is_______
distance Charting alignment on a graph requires a chart that is divided into thousandths
of an inch vertically for the indicator readings and into whole inches
horizontally for the__________
hidden The orthographic drawing may contain a dashed or _______ line
Radiation In order to shoot through a test object and project an image onto a detector or
a sheet of film, radiography uses a source of penetrating called _______
*scribe circles Which of the following task would you not perform with dividers?
*transfer measurements
*compare distances
<measure angles
10% The over speed trip device is actuated when the turbine reaches a
predetermined limit usually _________% above normal full-load speed
high Positive results in an offset measurement mean that the MTBM is _____ or on the
3-o'clock side.
offset misalignment The coupling gap is set, and then the ______ is measured
pressure In a hydraulic system, movement depends on_____
furniture or utility items Fractional dimensions are used on objects such as _______ or ______
, NCCER MILLWRIGHT PRACTICE EXAM 2
elimination If the cause of the problem is not immediately understood, the process
of________is often the procedure of choice
3/16 When applying sealant to the sealing gland flanges, keep the sealant away
from the inside edges of the flange by at least_______ inch
Transducer A stroboscope is triggered by a_______
thread The pitch of threaded fasteners is measured with a ________gauge
Surface cracks Liquid penetrant highlights flaws and reveals________
die A tool used to cut external threats on s bolt or rod is called a ______
special processes A bill of materials may include info on _______ and other reference information
surface speed Engaged gears always have the same _____
general arrangement Elevation of equipment is usually found in the_____
Vibrations Inspect the pulleys, rollers, and idlers for unevenness or______
15-20 degree angle When cutting thin steel with Oxyfuel fuel cutting equipment, hold the torch so
that the tip is pointing in the direction the torch is traveling at a _____ angle
Grease......... Labby seals work BEST with materials such as_____
Friction Lubrication is the application of any substance that reduces________
Driver coupling jig When the dial indicator is mounted on the complex reverse driven coupling jig
, the indicator is registered on the____
In racks Pipe should be stored_____
Single deep groove radial The most common type of ball bearing is a _____ bearing
split Couplings that are installed after the driver and driven shafts have been
aligned and the equipment has been fastened into position are ________
couplings
Factors When two or more numbers are multiplied to make another number thy ate
called _______of the third number
unusual If the seal was not properly aligned or there is excessive wear in some bearing
or shaft,_______ wear tracks will be the indicator
sharpened brass putty knife For removing hard to remove gasket materials found on sealing surfaces, ______
is recommended
Conducted on the job Apprenticeship training is_______
distance Charting alignment on a graph requires a chart that is divided into thousandths
of an inch vertically for the indicator readings and into whole inches
horizontally for the__________
hidden The orthographic drawing may contain a dashed or _______ line
Radiation In order to shoot through a test object and project an image onto a detector or
a sheet of film, radiography uses a source of penetrating called _______
*scribe circles Which of the following task would you not perform with dividers?
*transfer measurements
*compare distances
<measure angles
10% The over speed trip device is actuated when the turbine reaches a
predetermined limit usually _________% above normal full-load speed
high Positive results in an offset measurement mean that the MTBM is _____ or on the
3-o'clock side.
offset misalignment The coupling gap is set, and then the ______ is measured
pressure In a hydraulic system, movement depends on_____
furniture or utility items Fractional dimensions are used on objects such as _______ or ______
, NCCER MILLWRIGHT PRACTICE EXAM 2
elimination If the cause of the problem is not immediately understood, the process
of________is often the procedure of choice
3/16 When applying sealant to the sealing gland flanges, keep the sealant away
from the inside edges of the flange by at least_______ inch
Transducer A stroboscope is triggered by a_______
thread The pitch of threaded fasteners is measured with a ________gauge
Surface cracks Liquid penetrant highlights flaws and reveals________
die A tool used to cut external threats on s bolt or rod is called a ______
special processes A bill of materials may include info on _______ and other reference information
surface speed Engaged gears always have the same _____
general arrangement Elevation of equipment is usually found in the_____
Vibrations Inspect the pulleys, rollers, and idlers for unevenness or______
15-20 degree angle When cutting thin steel with Oxyfuel fuel cutting equipment, hold the torch so
that the tip is pointing in the direction the torch is traveling at a _____ angle
Grease......... Labby seals work BEST with materials such as_____
Friction Lubrication is the application of any substance that reduces________
Driver coupling jig When the dial indicator is mounted on the complex reverse driven coupling jig
, the indicator is registered on the____
In racks Pipe should be stored_____
Single deep groove radial The most common type of ball bearing is a _____ bearing
split Couplings that are installed after the driver and driven shafts have been
aligned and the equipment has been fastened into position are ________
couplings
Factors When two or more numbers are multiplied to make another number thy ate
called _______of the third number
