BXMO Basic X-ray Machine Operator
Exam Preparation
Section 1: Radiographic Physics, Equipment & X-ray
Production
1. What primary component inside the X-ray tube serves as the source of electrons
during exposure thermionic emission?
A. Anode target disc
B. Cathode tungsten filament
C. Induction motor stator
D. Beryllium port window
Option B is correct because heating the tungsten filament at the cathode releases free electrons via
thermionic emission. The anode target is where those electrons strike to produce X-rays.
2. Which electrical factor directly controls the penetrability and energy quality of the
primary X-ray beam?
A. Peak kilovoltage (kVp)
B. Milliamperage (mA)
C. Exposure duration (seconds)
D. Filament circuit resistance
Option A is correct because kVp regulates the potential difference across the tube, accelerating
electrons to higher kinetic energies and increasing beam penetrability.
3. What percentage of the total kinetic energy of colliding electrons at the anode target is
converted into actual X-ray photons during a standard diagnostic exposure?
A. Approximately 99%
B. Approximately 50%
C. Approximately 10%
D. Less than 1%
Option D is correct because over 99% of electron kinetic energy is converted into heat at the target,
leaving less than 1% emitted as useful X-ray radiation.
,4. According to the line-focus principle, how does angling the anode target affect the
effective focal spot size relative to the actual focal spot size?
A. The effective focal spot becomes larger than the actual focal spot
B. The effective focal spot becomes smaller than the actual focal spot
C. Both focal spot sizes remain exactly identical
D. The effective focal spot size fluctuates with changes in mA
Option B is correct because slanting the target projects a smaller effective focal spot for sharper image
detail while maintaining a larger actual focal spot area for heat dissipation.
5. What phenomenon causes greater X-ray beam intensity on the cathode side of the field
compared to the anode side?
A. Inverse square law
B. Bremsstrahlung radiation effect
C. Anode heel effect
D. Quantum mottle effect
Option C is correct because photons exiting the target heel travel through more target material,
causing increased attenuation toward the anode side and higher intensity toward the cathode side.
6. How should the operator position anatomical structures of varying thickness to take
advantage of the anode heel effect?
A. Place the thickest anatomical region under the anode end
B. Place the thickest anatomical region under the cathode end
C. Center the thinnest region directly under the collimator crosshairs
D. Position the patient perpendicular to the long axis of the table
Option B is correct because aligning thicker anatomy under the higher-intensity cathode side creates a
more uniform image density across the receptor.
7. What primary interaction between incident high-speed electrons and target nuclei
produces the majority of diagnostic X-ray photons?
A. Photoelectric absorption
B. Compton scattering
C. Bremsstrahlung (braking) radiation
D. Pair production
Option C is correct because Bremsstrahlung radiation accounts for roughly 85% to 90% of the
, diagnostic beam spectrum when projectile electrons slow down near tungsten nuclei.
8. What minimum total filtration is required by federal standards for diagnostic X-ray
units operating above 70 kVp?
A. 1.0 mm aluminum equivalent
B. 1.5 mm aluminum equivalent
C. 2.5 mm aluminum equivalent
D. 3.5 mm aluminum equivalent
Option C is correct because federal regulations mandate a minimum of 2.5 mm Al equivalent total
filtration for systems operating at or above 70 kVp to absorb soft, low-energy photons.
9. What primary function does added filtration serve in an X-ray housing system?
A. Increases overall beam intensity and image density
B. Removes low-energy, non-penetrating photons to reduce patient skin dose
C. Focuses the primary beam onto a smaller focal spot size
D. Prevents spatial distortion on digital image receptors
Option B is correct because low-energy photons absorb in superficial tissue without contributing to
image formation; filtering them "hardens" the beam and reduces skin entrance dose.
10. Which exposure variable directly governs the total quantity of X-ray photons
produced during an exposure?
A. Peak kilovoltage (kVp)
B. Source-to-image distance (SID)
C. Milliampere-seconds (mAs)
D. Grid ratio
Option C is correct because mAs is the product of tube current (mA) and exposure duration (seconds),
directly determining the total number of photons emitted.
11. What component in an X-ray circuit steps up incoming line voltage to the high voltage
needed for X-ray production?
A. Autotransformer
B. Step-up high-voltage transformer
C. Filament step-down transformer
D. Rheostat control
Exam Preparation
Section 1: Radiographic Physics, Equipment & X-ray
Production
1. What primary component inside the X-ray tube serves as the source of electrons
during exposure thermionic emission?
A. Anode target disc
B. Cathode tungsten filament
C. Induction motor stator
D. Beryllium port window
Option B is correct because heating the tungsten filament at the cathode releases free electrons via
thermionic emission. The anode target is where those electrons strike to produce X-rays.
2. Which electrical factor directly controls the penetrability and energy quality of the
primary X-ray beam?
A. Peak kilovoltage (kVp)
B. Milliamperage (mA)
C. Exposure duration (seconds)
D. Filament circuit resistance
Option A is correct because kVp regulates the potential difference across the tube, accelerating
electrons to higher kinetic energies and increasing beam penetrability.
3. What percentage of the total kinetic energy of colliding electrons at the anode target is
converted into actual X-ray photons during a standard diagnostic exposure?
A. Approximately 99%
B. Approximately 50%
C. Approximately 10%
D. Less than 1%
Option D is correct because over 99% of electron kinetic energy is converted into heat at the target,
leaving less than 1% emitted as useful X-ray radiation.
,4. According to the line-focus principle, how does angling the anode target affect the
effective focal spot size relative to the actual focal spot size?
A. The effective focal spot becomes larger than the actual focal spot
B. The effective focal spot becomes smaller than the actual focal spot
C. Both focal spot sizes remain exactly identical
D. The effective focal spot size fluctuates with changes in mA
Option B is correct because slanting the target projects a smaller effective focal spot for sharper image
detail while maintaining a larger actual focal spot area for heat dissipation.
5. What phenomenon causes greater X-ray beam intensity on the cathode side of the field
compared to the anode side?
A. Inverse square law
B. Bremsstrahlung radiation effect
C. Anode heel effect
D. Quantum mottle effect
Option C is correct because photons exiting the target heel travel through more target material,
causing increased attenuation toward the anode side and higher intensity toward the cathode side.
6. How should the operator position anatomical structures of varying thickness to take
advantage of the anode heel effect?
A. Place the thickest anatomical region under the anode end
B. Place the thickest anatomical region under the cathode end
C. Center the thinnest region directly under the collimator crosshairs
D. Position the patient perpendicular to the long axis of the table
Option B is correct because aligning thicker anatomy under the higher-intensity cathode side creates a
more uniform image density across the receptor.
7. What primary interaction between incident high-speed electrons and target nuclei
produces the majority of diagnostic X-ray photons?
A. Photoelectric absorption
B. Compton scattering
C. Bremsstrahlung (braking) radiation
D. Pair production
Option C is correct because Bremsstrahlung radiation accounts for roughly 85% to 90% of the
, diagnostic beam spectrum when projectile electrons slow down near tungsten nuclei.
8. What minimum total filtration is required by federal standards for diagnostic X-ray
units operating above 70 kVp?
A. 1.0 mm aluminum equivalent
B. 1.5 mm aluminum equivalent
C. 2.5 mm aluminum equivalent
D. 3.5 mm aluminum equivalent
Option C is correct because federal regulations mandate a minimum of 2.5 mm Al equivalent total
filtration for systems operating at or above 70 kVp to absorb soft, low-energy photons.
9. What primary function does added filtration serve in an X-ray housing system?
A. Increases overall beam intensity and image density
B. Removes low-energy, non-penetrating photons to reduce patient skin dose
C. Focuses the primary beam onto a smaller focal spot size
D. Prevents spatial distortion on digital image receptors
Option B is correct because low-energy photons absorb in superficial tissue without contributing to
image formation; filtering them "hardens" the beam and reduces skin entrance dose.
10. Which exposure variable directly governs the total quantity of X-ray photons
produced during an exposure?
A. Peak kilovoltage (kVp)
B. Source-to-image distance (SID)
C. Milliampere-seconds (mAs)
D. Grid ratio
Option C is correct because mAs is the product of tube current (mA) and exposure duration (seconds),
directly determining the total number of photons emitted.
11. What component in an X-ray circuit steps up incoming line voltage to the high voltage
needed for X-ray production?
A. Autotransformer
B. Step-up high-voltage transformer
C. Filament step-down transformer
D. Rheostat control