SOS MECHANIC CERTIFICATE ENGINE
REPAIR EXAM PREP TEST BANK VERIFIED
QUESTIONS AND CORRECT ANSWERS
●● ASTM
Answer: The American Society for Testing and Materials.
●● Acute Area of the Windshield
Answer: The center of the critical area on the driver's side of the vehicle
directly in the
driver's normal line of vision 81/2 inches wide and 51/2 inches high.
●● Allowable Working Pressure
Answer: The pounds per square inch for which the container was
constructed, or if
conditions have changed, the maximum pressure at specified
temperatures permitted at the most recent inspection
by a certified inspector.
●● Alteration
Answer: A change in the construction, design, or installation of a
container that affects the strength or safety of
the system.
,●● Auxiliary driving Lamp
Answer: A lighting device mounted to provide illumination in front of
the vehicle and to supplement the upper beam of a standard headlamp
system; it is not intended for use alone or with the lower beam of a
standard headlamp system
●● Back-Up Lamp
Answer: A lamp used to provide illumination behind the vehicle and to
provide a warning signal when the vehicle is in reverse gear.
●● Bead
Answer: The part of the tire made of steel wires wrapped or reinforced
by ply cords, that is shaped to fit the rim.
●● Belt
Answer: A layer made of fabric or other material located under the tread
area.
●● Bureau
Answer: The Bureau of Motor Vehicles of the Department.
●● CGA
, Answer: The Compressed Gas Association, Inc.; 14501 George Carter
Way, Suite 103, Chantilly, VA 20151.
●● Cargo Lamp
Answer: A lamp mounted on a multipurpose passenger vehicle, truck or
bus that provides illumination to load or unload cargo
●● Certified Inspection Mechanic
Answer: A person who holds a valid certification card issued by the
Bureau certifying that the person is qualified, has passed all
requirements to inspect specific vehicles and holds a valid driver's
license for the correct class of vehicle
●● Certified Inspector
Answer: A person who holds a certificate issued by the Boiler Division
in the Bureau of Occupation and Industrial Safety within the Department
of Labor and Industry certifying that the person is qualified to inspect
unfired pressure vessels.
●● Clearance Lamps
Answer: Lamps which show to the front or rear of a vehicle to indicate
overall width and height of a vehicle -- on trucks and buses 80 inches or
more in width.
●● Commonwealth Inspection Station
REPAIR EXAM PREP TEST BANK VERIFIED
QUESTIONS AND CORRECT ANSWERS
●● ASTM
Answer: The American Society for Testing and Materials.
●● Acute Area of the Windshield
Answer: The center of the critical area on the driver's side of the vehicle
directly in the
driver's normal line of vision 81/2 inches wide and 51/2 inches high.
●● Allowable Working Pressure
Answer: The pounds per square inch for which the container was
constructed, or if
conditions have changed, the maximum pressure at specified
temperatures permitted at the most recent inspection
by a certified inspector.
●● Alteration
Answer: A change in the construction, design, or installation of a
container that affects the strength or safety of
the system.
,●● Auxiliary driving Lamp
Answer: A lighting device mounted to provide illumination in front of
the vehicle and to supplement the upper beam of a standard headlamp
system; it is not intended for use alone or with the lower beam of a
standard headlamp system
●● Back-Up Lamp
Answer: A lamp used to provide illumination behind the vehicle and to
provide a warning signal when the vehicle is in reverse gear.
●● Bead
Answer: The part of the tire made of steel wires wrapped or reinforced
by ply cords, that is shaped to fit the rim.
●● Belt
Answer: A layer made of fabric or other material located under the tread
area.
●● Bureau
Answer: The Bureau of Motor Vehicles of the Department.
●● CGA
, Answer: The Compressed Gas Association, Inc.; 14501 George Carter
Way, Suite 103, Chantilly, VA 20151.
●● Cargo Lamp
Answer: A lamp mounted on a multipurpose passenger vehicle, truck or
bus that provides illumination to load or unload cargo
●● Certified Inspection Mechanic
Answer: A person who holds a valid certification card issued by the
Bureau certifying that the person is qualified, has passed all
requirements to inspect specific vehicles and holds a valid driver's
license for the correct class of vehicle
●● Certified Inspector
Answer: A person who holds a certificate issued by the Boiler Division
in the Bureau of Occupation and Industrial Safety within the Department
of Labor and Industry certifying that the person is qualified to inspect
unfired pressure vessels.
●● Clearance Lamps
Answer: Lamps which show to the front or rear of a vehicle to indicate
overall width and height of a vehicle -- on trucks and buses 80 inches or
more in width.
●● Commonwealth Inspection Station
