Champions Home Inspection Module 1 Exam with all
Correct & 100% Verified Answers |Actual Complete Exam
|Already Graded A+
Gutter downspouts should discharge how many feet from the foundation. ✔Correct Answer-5
ft
Over watering can cause foundation problems and damage the structure. ✔Correct Answer-
True
Optimum moisture content shows the minimum soil moisture changes. ✔Correct Answer-
True
What is good maintenance for Pier and Beam. ✔Correct Answer-Good Ventilation
Minimum swelling point of expansive soil is. ✔Correct Answer-5000 psi
Minimum swelling point of concrete is. ✔Correct Answer-3000 psi
Abbreviation for Southern Pine. ✔Correct Answer-SYP
Abbreviation for Spruce-Pine-Fir. ✔Correct Answer-S-P-F (S) (S stands for South or USA)
Abbreviation for Douglas Fir-Larch. ✔Correct Answer-D.Fir-L (N) (N stands for North or
Canada)
A bored hole and notch cannot be in the same cross section in exterior walls, load bearing walls,
and interior non-load bearing walls. ✔Correct Answer-True
5/8 minimum to edge when boring holes in all wall studs. ✔Correct Answer-True
A bored hole in an interior non-load bearing wall shall not exceed ____% of stud depth.
✔Correct Answer-60%
A bored hole in an exterior wall and/or a load bearing wall shall not exceed ____% of stud
depth. ✔Correct Answer-40%
A notch must not exceed ____% of stud depth. ✔Correct Answer-25%
If a hole is bored between 40%-60% of stud depth what can be done. ✔Correct Answer-Stud
can be doubled. But no more than two successive studs can be doubled.
,Engineered Wood products may be used as columns, beams, and floor joist. ✔Correct
Answer-True
Engineered Wood products allows holes only in the ____ 1/3rd of beams and headers.
✔Correct Answer-Middle 1/3rd
A minimum of ____ inch space shall be provided between insulation and roof sheathing at the
location of a vent in an attic. ✔Correct Answer-1 inch
Fireblocking material consists of ____ inch nominal lumber. ✔Correct Answer-2 inch
Fireblocking materials consists of two thicknesses of ____ inch nominal lumber. ✔Correct
Answer-1 inch
Particleboard fireblocking material consists of what thickness. ✔Correct Answer-3/4 inch
particleboard
Fireblocking gypsum board is how many inches. ✔Correct Answer-1/2 inch
Batts or blankets of mineralwool or glass fiber are approved fireblocking material. ✔Correct
Answer-True
Approved fireblocking material of cement-based millboard needs to be how many inches.
✔Correct Answer-1/4 inches
SIP's stands for. ✔Correct Answer-Structural Insulated Panels
ICF's stands for. ✔Correct Answer-Insulated Concrete Forms
These panels have one layer of foam insulation sandwiched between two layers of building
materials. ✔Correct Answer-SIP's (structural insulated panels)
These panels have a layer of concrete sandwiched by two layers of foam insulation. ✔Correct
Answer-ICF's (insulated concrete forms)
Both SIP's and ICF's have a high R-value without the need for a vapor barrier. ✔Correct
Answer-True
What is the downside of using SIP's or ICF's. ✔Correct Answer-More expensive than a typical
framed house.
What does STUFL stand for in reference to steel framing. ✔Correct Answer-Stud, Track, U
channel, Furring, L header
, What 3 types of screws (fasteners) will address almost all applications regarding steel framing.
✔Correct Answer-Hex head, Pan head, Bugle head
Dishwasher cord length. ✔Correct Answer-36-78 inches
Trash compactor cord lenght. ✔Correct Answer-36-78 inches
Food Disposer cord length. ✔Correct Answer-18-36 inches
The typical lifespan for most major appliances is ____-____ years. ✔Correct Answer-10-20
years
Range hood exhausts is not permitted into attics or crawl spaces. ✔Correct Answer-True
Combustible materials, such as cabinets, should have a minimum of ____ inches of clearance
above the burners. ✔Correct Answer-30 inches
Non combustible materials, such as a microwave or exhaust fan, should have a minimum of
____ inches of clearance above burners. ✔Correct Answer-24 inches
Gas burners that fail to light consistently may need...... ✔Correct Answer-an adjustment to
their regulator or ignitor.
Gas flex connections may be no more than ____ feet from the applicance. ✔Correct Answer-6
feet
A gas shutoff should be no more than ____ feet from the applicance. ✔Correct Answer-6 feet
An oven that shows a 25 degree difference should be reported. ✔Correct Answer-True
Weak door springs that fail to support the oven doors weight should be reported. ✔Correct
Answer-True
Bathroom exhaust fans should exhaust/terminate where. ✔Correct Answer-Outdoors
Terminating a bathroom exhaust into an attic/crawl space can cause mildew or wood rot
conditions. ✔Correct Answer-True
Garage door eye sensors must be installed within ____ inches of the floor. ✔Correct Answer-6
inches
Automatic garage doors must have a safety provision that automatically reverses direction if an
obstruction exists. ✔Correct Answer-True
Correct & 100% Verified Answers |Actual Complete Exam
|Already Graded A+
Gutter downspouts should discharge how many feet from the foundation. ✔Correct Answer-5
ft
Over watering can cause foundation problems and damage the structure. ✔Correct Answer-
True
Optimum moisture content shows the minimum soil moisture changes. ✔Correct Answer-
True
What is good maintenance for Pier and Beam. ✔Correct Answer-Good Ventilation
Minimum swelling point of expansive soil is. ✔Correct Answer-5000 psi
Minimum swelling point of concrete is. ✔Correct Answer-3000 psi
Abbreviation for Southern Pine. ✔Correct Answer-SYP
Abbreviation for Spruce-Pine-Fir. ✔Correct Answer-S-P-F (S) (S stands for South or USA)
Abbreviation for Douglas Fir-Larch. ✔Correct Answer-D.Fir-L (N) (N stands for North or
Canada)
A bored hole and notch cannot be in the same cross section in exterior walls, load bearing walls,
and interior non-load bearing walls. ✔Correct Answer-True
5/8 minimum to edge when boring holes in all wall studs. ✔Correct Answer-True
A bored hole in an interior non-load bearing wall shall not exceed ____% of stud depth.
✔Correct Answer-60%
A bored hole in an exterior wall and/or a load bearing wall shall not exceed ____% of stud
depth. ✔Correct Answer-40%
A notch must not exceed ____% of stud depth. ✔Correct Answer-25%
If a hole is bored between 40%-60% of stud depth what can be done. ✔Correct Answer-Stud
can be doubled. But no more than two successive studs can be doubled.
,Engineered Wood products may be used as columns, beams, and floor joist. ✔Correct
Answer-True
Engineered Wood products allows holes only in the ____ 1/3rd of beams and headers.
✔Correct Answer-Middle 1/3rd
A minimum of ____ inch space shall be provided between insulation and roof sheathing at the
location of a vent in an attic. ✔Correct Answer-1 inch
Fireblocking material consists of ____ inch nominal lumber. ✔Correct Answer-2 inch
Fireblocking materials consists of two thicknesses of ____ inch nominal lumber. ✔Correct
Answer-1 inch
Particleboard fireblocking material consists of what thickness. ✔Correct Answer-3/4 inch
particleboard
Fireblocking gypsum board is how many inches. ✔Correct Answer-1/2 inch
Batts or blankets of mineralwool or glass fiber are approved fireblocking material. ✔Correct
Answer-True
Approved fireblocking material of cement-based millboard needs to be how many inches.
✔Correct Answer-1/4 inches
SIP's stands for. ✔Correct Answer-Structural Insulated Panels
ICF's stands for. ✔Correct Answer-Insulated Concrete Forms
These panels have one layer of foam insulation sandwiched between two layers of building
materials. ✔Correct Answer-SIP's (structural insulated panels)
These panels have a layer of concrete sandwiched by two layers of foam insulation. ✔Correct
Answer-ICF's (insulated concrete forms)
Both SIP's and ICF's have a high R-value without the need for a vapor barrier. ✔Correct
Answer-True
What is the downside of using SIP's or ICF's. ✔Correct Answer-More expensive than a typical
framed house.
What does STUFL stand for in reference to steel framing. ✔Correct Answer-Stud, Track, U
channel, Furring, L header
, What 3 types of screws (fasteners) will address almost all applications regarding steel framing.
✔Correct Answer-Hex head, Pan head, Bugle head
Dishwasher cord length. ✔Correct Answer-36-78 inches
Trash compactor cord lenght. ✔Correct Answer-36-78 inches
Food Disposer cord length. ✔Correct Answer-18-36 inches
The typical lifespan for most major appliances is ____-____ years. ✔Correct Answer-10-20
years
Range hood exhausts is not permitted into attics or crawl spaces. ✔Correct Answer-True
Combustible materials, such as cabinets, should have a minimum of ____ inches of clearance
above the burners. ✔Correct Answer-30 inches
Non combustible materials, such as a microwave or exhaust fan, should have a minimum of
____ inches of clearance above burners. ✔Correct Answer-24 inches
Gas burners that fail to light consistently may need...... ✔Correct Answer-an adjustment to
their regulator or ignitor.
Gas flex connections may be no more than ____ feet from the applicance. ✔Correct Answer-6
feet
A gas shutoff should be no more than ____ feet from the applicance. ✔Correct Answer-6 feet
An oven that shows a 25 degree difference should be reported. ✔Correct Answer-True
Weak door springs that fail to support the oven doors weight should be reported. ✔Correct
Answer-True
Bathroom exhaust fans should exhaust/terminate where. ✔Correct Answer-Outdoors
Terminating a bathroom exhaust into an attic/crawl space can cause mildew or wood rot
conditions. ✔Correct Answer-True
Garage door eye sensors must be installed within ____ inches of the floor. ✔Correct Answer-6
inches
Automatic garage doors must have a safety provision that automatically reverses direction if an
obstruction exists. ✔Correct Answer-True
