Amazon AE 2026 Training Test
In order to prevent other devices from overheating, the Near the top
best place to install a VFD is ___________ of the control
panel. (10)
The __________ configuration software replaces the New Module Wizard
hardware DIP switches and jumpers used to configure
earlier PLC analog modules.
__________ modules sense the variable signal level Analog input
applied to their terminals and convert it into a digital value.
NEMA overloads often use melting alloy thermal
overloads. (48)
True ✅
The type of manual starter used for three-phase motors is
a __________. (48)
Integral horsepower starter ✅
A magnetic overload includes a dashpot which allows
adjustments to the response time of the overload. (48)
True ✅
A motor starter is the same as a motor controller. (48) False ✅
Which of the following is a basic requirement for a typical
motor installation? (48)
All of the above
(Controller
✅
Short circuit protection
Disconnect)
__________ protection on a manual starter will prevent the
automatic restart of a motor when recovering from a power
Undervoltage ✅
loss. (48)
Some manual motor starters use a special sensing coil
that verifies the presence of incoming voltage to open the
True ✅
starter contacts when the voltage is below a preset level.
(48)
The contacts of a manual starter will remain in the
actuated position when power is lost. (48)
True ✅
Which type of overload uses a coil to sense the level of
motor current? (48)
Magnetic overload ✅
Magnetic contactors open and close their contacts through
the use of a magnetic coil. (48)
True ✅
Which of the following is a function of motor control? (48) Speed control ✅
, Amazon AE 2026 Training Test
Bimetallic overloads do not allow you to adjust the trip
point. (48)
False ✅
A ground fault occurs when __________. (47) One of the phases becomes grounded ✅
Which of the following is not a result of connecting a dual-
voltage motor to operate on the higher voltage? (47)
Increased current draw ✅
A grounded neutral wire can be used as an equipment
ground. (47)
False ✅
Which of the following is not a part of a fusible disconnect?
(47)
None of the above
(Fuses
✅
Manually-operated switch
Enclosure)
Which of the following is a factor that must be considered
when selecting overcurrent protection devices for a motor
Rated full-load current of the motor ✅
control circuit? (47)
Which of the following is not a basic rule of electrical
safety? (47)
Always work by yourself. ✅
Which of the following is not a common voltage supplied
by a wye-configured system? (47)
240 VAC ✅
A time-delay fuse only has one element. (47) False ✅
Three-phase power is transmitted in phases that are
__________ degrees apart. (47)
120 ✅
Which of the following is a component of a typical three-
phase squirrel-cage motor? (47)
All of the above
(Copper bars
✅
End rings
Iron core)
The __________ is the accepted standard in the United
States for safely installing and maintaining electrical
NEC ✅
systems and equipment. (47)
Parts of an electrical system that should be connected to
earth ground include __________. (47)
All of the above
(Metal raceways
✅
Metal conduit
Metal enclosures)
Who should remove a lockout/tagout? (47) Only the person(s) who installed it ✅
, Amazon AE 2026 Training Test
Which of the following items on a motor's nameplate is
used to determine how much output power a motor can
Service Factor ✅
safely produce above its rated output power? (47)
If the service factor for a motor is not given on the
nameplate, what should you assume the service factor to
1 ✅
be? (47)
Analog modules contain more information than discrete
modules and require __________. (46)
A more complex tag structure ✅
The Studio 5000 software configuration replaces the
__________ used to configure earlier PLC analog
DIP switches and jumpers ✅
modules. (46)
The __________ is used to view a CompactLogix analog
output module's configuration status and channel data.
Tag Monitor utility ✅
(46)
To troubleshoot analog modules, it is important to know
what information is stored in __________ and where to
The tag structure ✅
find it. (46)
The __________ settings are used to match the output
channel signal to the signal required by the output device
Output Configuration ✅
and/or application being controlled. (46)
Output configuration settings are used to match the
__________ to the signal required by the output device
Output channel signal ✅
and/or application being controlled. (46)
__________ is used to prevent installation of a module in
the wrong slot in a chassis. (46)
Electronic keying ✅
The __________ of an output transducer is the resulting
change in physical output given a signal change to the
Sensitivity ✅
input. (45)
A(n) __________ is a device that converts energy from
one form to another. (45)
Transducer ✅
In North America, the __________ signal is the most
commonly used signal range for output devices. (45)
4 mA to 20 mA ✅
CompactLogix __________ modules receive digital output
values from the controller, manipulate them according to
Analog output ✅
user-supplied configuration data, and then convert them
into variable signals that are applied to the module
terminals and ultimately an output device. (45)
CompactLogix analog output modules receive
__________ values from the controller, manipulates them
Digital output ✅
according to configuration data, then converts them into
variable signals that are ultimately applied to an output
device. (45)
, Amazon AE 2026 Training Test
__________ refers to the ability of the device's digital-to-
analog converter (D/A converter) to produce a smooth
Resolution ✅
analog output. (45)
The ability to __________ the physical output signal of an
output transducer for a given input is a useful skill for
Calculate ✅
troubleshooting and design. (45)
The __________ instruction only passes true rung
continuity when the value of Source A is greater than the
GRT ✅
value of Source B. (44)
__________ instruction is not intended to compare
numerical values. (44)
MEQ ✅
A program that controls an oven uses one __________
instruction to activate the low temperature OTE. (44)
LEQ ✅
__________ instruction has the ability to utilize algebraic
comparison symbols along with operators +,-, *, and / to
CMP ✅
mathematically modify a source input. (44)
On/off control systems maintain the state of a process by
keeping the process __________ within a specified
Variable ✅
operating range. (44)
After an analog input module is initially configured, the
parameters can be edited using the __________ utility.
Module Properties ✅
(43)
__________ tag structures are automatically created when
an analog input module is added to the controller's I/O
Module-defined ✅
configuration. (43) (46)
__________ parameters define how often the analog input
module sends data to the controller, if at all, as well as the
Connection screen ✅
controller fault handling if communication is disrupted. (43)
The data stored by CompactLogix analog modules can be
viewed using the __________ feature of Studio 5000
Tag Monitor ✅
software. (43)
__________ modules sense the variable signal level
applied to their terminals and convert it into a digital value.
Analog input ✅
(42)
Data on the __________ tab comes directly from the
analog output module. Studio 5000 must be online with the
Module Info ✅
processor to display status information. (42)
__________ is used to prevent installation of a module in
the wrong slot in a chassis. (42)
Electronic keying ✅
The analog input module __________ the raw digital value
into a value in engineering units. (42)
Converts ✅
In order to prevent other devices from overheating, the Near the top
best place to install a VFD is ___________ of the control
panel. (10)
The __________ configuration software replaces the New Module Wizard
hardware DIP switches and jumpers used to configure
earlier PLC analog modules.
__________ modules sense the variable signal level Analog input
applied to their terminals and convert it into a digital value.
NEMA overloads often use melting alloy thermal
overloads. (48)
True ✅
The type of manual starter used for three-phase motors is
a __________. (48)
Integral horsepower starter ✅
A magnetic overload includes a dashpot which allows
adjustments to the response time of the overload. (48)
True ✅
A motor starter is the same as a motor controller. (48) False ✅
Which of the following is a basic requirement for a typical
motor installation? (48)
All of the above
(Controller
✅
Short circuit protection
Disconnect)
__________ protection on a manual starter will prevent the
automatic restart of a motor when recovering from a power
Undervoltage ✅
loss. (48)
Some manual motor starters use a special sensing coil
that verifies the presence of incoming voltage to open the
True ✅
starter contacts when the voltage is below a preset level.
(48)
The contacts of a manual starter will remain in the
actuated position when power is lost. (48)
True ✅
Which type of overload uses a coil to sense the level of
motor current? (48)
Magnetic overload ✅
Magnetic contactors open and close their contacts through
the use of a magnetic coil. (48)
True ✅
Which of the following is a function of motor control? (48) Speed control ✅
, Amazon AE 2026 Training Test
Bimetallic overloads do not allow you to adjust the trip
point. (48)
False ✅
A ground fault occurs when __________. (47) One of the phases becomes grounded ✅
Which of the following is not a result of connecting a dual-
voltage motor to operate on the higher voltage? (47)
Increased current draw ✅
A grounded neutral wire can be used as an equipment
ground. (47)
False ✅
Which of the following is not a part of a fusible disconnect?
(47)
None of the above
(Fuses
✅
Manually-operated switch
Enclosure)
Which of the following is a factor that must be considered
when selecting overcurrent protection devices for a motor
Rated full-load current of the motor ✅
control circuit? (47)
Which of the following is not a basic rule of electrical
safety? (47)
Always work by yourself. ✅
Which of the following is not a common voltage supplied
by a wye-configured system? (47)
240 VAC ✅
A time-delay fuse only has one element. (47) False ✅
Three-phase power is transmitted in phases that are
__________ degrees apart. (47)
120 ✅
Which of the following is a component of a typical three-
phase squirrel-cage motor? (47)
All of the above
(Copper bars
✅
End rings
Iron core)
The __________ is the accepted standard in the United
States for safely installing and maintaining electrical
NEC ✅
systems and equipment. (47)
Parts of an electrical system that should be connected to
earth ground include __________. (47)
All of the above
(Metal raceways
✅
Metal conduit
Metal enclosures)
Who should remove a lockout/tagout? (47) Only the person(s) who installed it ✅
, Amazon AE 2026 Training Test
Which of the following items on a motor's nameplate is
used to determine how much output power a motor can
Service Factor ✅
safely produce above its rated output power? (47)
If the service factor for a motor is not given on the
nameplate, what should you assume the service factor to
1 ✅
be? (47)
Analog modules contain more information than discrete
modules and require __________. (46)
A more complex tag structure ✅
The Studio 5000 software configuration replaces the
__________ used to configure earlier PLC analog
DIP switches and jumpers ✅
modules. (46)
The __________ is used to view a CompactLogix analog
output module's configuration status and channel data.
Tag Monitor utility ✅
(46)
To troubleshoot analog modules, it is important to know
what information is stored in __________ and where to
The tag structure ✅
find it. (46)
The __________ settings are used to match the output
channel signal to the signal required by the output device
Output Configuration ✅
and/or application being controlled. (46)
Output configuration settings are used to match the
__________ to the signal required by the output device
Output channel signal ✅
and/or application being controlled. (46)
__________ is used to prevent installation of a module in
the wrong slot in a chassis. (46)
Electronic keying ✅
The __________ of an output transducer is the resulting
change in physical output given a signal change to the
Sensitivity ✅
input. (45)
A(n) __________ is a device that converts energy from
one form to another. (45)
Transducer ✅
In North America, the __________ signal is the most
commonly used signal range for output devices. (45)
4 mA to 20 mA ✅
CompactLogix __________ modules receive digital output
values from the controller, manipulate them according to
Analog output ✅
user-supplied configuration data, and then convert them
into variable signals that are applied to the module
terminals and ultimately an output device. (45)
CompactLogix analog output modules receive
__________ values from the controller, manipulates them
Digital output ✅
according to configuration data, then converts them into
variable signals that are ultimately applied to an output
device. (45)
, Amazon AE 2026 Training Test
__________ refers to the ability of the device's digital-to-
analog converter (D/A converter) to produce a smooth
Resolution ✅
analog output. (45)
The ability to __________ the physical output signal of an
output transducer for a given input is a useful skill for
Calculate ✅
troubleshooting and design. (45)
The __________ instruction only passes true rung
continuity when the value of Source A is greater than the
GRT ✅
value of Source B. (44)
__________ instruction is not intended to compare
numerical values. (44)
MEQ ✅
A program that controls an oven uses one __________
instruction to activate the low temperature OTE. (44)
LEQ ✅
__________ instruction has the ability to utilize algebraic
comparison symbols along with operators +,-, *, and / to
CMP ✅
mathematically modify a source input. (44)
On/off control systems maintain the state of a process by
keeping the process __________ within a specified
Variable ✅
operating range. (44)
After an analog input module is initially configured, the
parameters can be edited using the __________ utility.
Module Properties ✅
(43)
__________ tag structures are automatically created when
an analog input module is added to the controller's I/O
Module-defined ✅
configuration. (43) (46)
__________ parameters define how often the analog input
module sends data to the controller, if at all, as well as the
Connection screen ✅
controller fault handling if communication is disrupted. (43)
The data stored by CompactLogix analog modules can be
viewed using the __________ feature of Studio 5000
Tag Monitor ✅
software. (43)
__________ modules sense the variable signal level
applied to their terminals and convert it into a digital value.
Analog input ✅
(42)
Data on the __________ tab comes directly from the
analog output module. Studio 5000 must be online with the
Module Info ✅
processor to display status information. (42)
__________ is used to prevent installation of a module in
the wrong slot in a chassis. (42)
Electronic keying ✅
The analog input module __________ the raw digital value
into a value in engineering units. (42)
Converts ✅
