Ultimate NEIEP Mechanics Brand New Revised Study Guide Exam latest 202
Actual Exam Questions and Correct Detailed Answers | with Rationales
Study online at https://quizlet.com/_jnn0p4
1. How do you calculate the number of counter- Use the formula LxWxHx.25, where the
weights needed to balance a car? weight of the counterweight is 25 lbs
per foot cubed.
2. Who is responsible for providing the MSDS on Your employer.
a construction site?
3. If a pump pulley is 6" and the motor pulley Cross multiply based on the pulley sizes
is 12", how do you determine the size pul- and motor speed.
ley needed to achieve a speed of 125' per
minute?
4. In a dump switch question, if the switches are Find the switch in the neutral position;
in certain states, how do you determine the the answer is believed to be the second
car's position? floor.
5. How many gallons of oil are needed to raise It would take 37 gallons of oil.
a car with a 6" diameter piston and a 25' rise?
6. How do you convert 1 inch to millimeters? 1 inch is equal to 25.4 mm.
7. What is the correct method to measure a Measure in flat sections on the incline
handrail? only.
8. When is an escape hatch required for resi- When there are no controls inside the
dential lifts? car and it must open to the outside.
9. How many wires are needed to wire a COP? You need 10% extra wires, considering
multiple common terminals.
10. What could be the cause if a brake doesn't It could be related to the brake circuit.
pick fully upon acceleration?
, Ultimate NEIEP Mechanics Brand New Revised Study Guide Exam latest 202
Actual Exam Questions and Correct Detailed Answers | with Rationales
Study online at https://quizlet.com/_jnn0p4
11. What is the formula for calculating the time TC = RxC, and capacitors take 5 times to
constant of a capacitor? charge.
12. What issue arises if doors open and close It indicates a problem with the off delay
immediately? circuit.
13. What should you ask for when installing rails? Fish plates.
14. When is the first tie down required for 2'x8' At 4 times the smallest base diameter,
scaffolding? find the closest header above.
15. What hole should you drill first when drop- Drill the deflector sheave hole first.
ping in machine beams?
16. At what speeds do mechanical and electrical For 300 fpm, mechanical trip at 395 and
trips occur for cars running at 300-350 fpm? electrical at 355; for 350 fpm, mechan-
ical trip at 454 and electrical at 407.
17. What types of safeties should be equipped Type A safeties (no more than 150 fpm)
for cars running at 300 fpm? and Type B wedge clamp.
18. What is an acceptable way to test oil buffers? Test for 90 seconds at high speed/in-
spection speed.
19. If a car is at the bottom normally, which way The car will not run down; it will run up.
will it not run?
20. How do you test safeties annually? Conduct a low speed no load Category
one elevator test.
21. What is the proper method for drilling into Use eye protection, drill slowly and
stainless steel doors? steadily with a sharp bit and cutting oil.
22. What is the method for drilling into sand? Use a rotary drill.
Actual Exam Questions and Correct Detailed Answers | with Rationales
Study online at https://quizlet.com/_jnn0p4
1. How do you calculate the number of counter- Use the formula LxWxHx.25, where the
weights needed to balance a car? weight of the counterweight is 25 lbs
per foot cubed.
2. Who is responsible for providing the MSDS on Your employer.
a construction site?
3. If a pump pulley is 6" and the motor pulley Cross multiply based on the pulley sizes
is 12", how do you determine the size pul- and motor speed.
ley needed to achieve a speed of 125' per
minute?
4. In a dump switch question, if the switches are Find the switch in the neutral position;
in certain states, how do you determine the the answer is believed to be the second
car's position? floor.
5. How many gallons of oil are needed to raise It would take 37 gallons of oil.
a car with a 6" diameter piston and a 25' rise?
6. How do you convert 1 inch to millimeters? 1 inch is equal to 25.4 mm.
7. What is the correct method to measure a Measure in flat sections on the incline
handrail? only.
8. When is an escape hatch required for resi- When there are no controls inside the
dential lifts? car and it must open to the outside.
9. How many wires are needed to wire a COP? You need 10% extra wires, considering
multiple common terminals.
10. What could be the cause if a brake doesn't It could be related to the brake circuit.
pick fully upon acceleration?
, Ultimate NEIEP Mechanics Brand New Revised Study Guide Exam latest 202
Actual Exam Questions and Correct Detailed Answers | with Rationales
Study online at https://quizlet.com/_jnn0p4
11. What is the formula for calculating the time TC = RxC, and capacitors take 5 times to
constant of a capacitor? charge.
12. What issue arises if doors open and close It indicates a problem with the off delay
immediately? circuit.
13. What should you ask for when installing rails? Fish plates.
14. When is the first tie down required for 2'x8' At 4 times the smallest base diameter,
scaffolding? find the closest header above.
15. What hole should you drill first when drop- Drill the deflector sheave hole first.
ping in machine beams?
16. At what speeds do mechanical and electrical For 300 fpm, mechanical trip at 395 and
trips occur for cars running at 300-350 fpm? electrical at 355; for 350 fpm, mechan-
ical trip at 454 and electrical at 407.
17. What types of safeties should be equipped Type A safeties (no more than 150 fpm)
for cars running at 300 fpm? and Type B wedge clamp.
18. What is an acceptable way to test oil buffers? Test for 90 seconds at high speed/in-
spection speed.
19. If a car is at the bottom normally, which way The car will not run down; it will run up.
will it not run?
20. How do you test safeties annually? Conduct a low speed no load Category
one elevator test.
21. What is the proper method for drilling into Use eye protection, drill slowly and
stainless steel doors? steadily with a sharp bit and cutting oil.
22. What is the method for drilling into sand? Use a rotary drill.
