PROPANE FINAL PRACTICE 2026/2027
QUESTIONS AND CORRECT ANSWERS GRADED
A+
ASME code refers to the __________ of the American Society of Mechanical
Engineers.
Boiler and pressure vessel code
A chimney for residential type or low heat appliances shall extend at least 2 feet
higher than any portion of a building with a horizontal distance of __________.
10 feet
The location where connections and disconnections are made or where LP-Gas
vented to the atmosphere in the course of transfer operations is known as
__________.
Point of transfer
Appliances or equipment that, because of their intended modes of use or operation,
are capable of providing sufficient thermal energy to ignite flammable gas-air
mixtures are known as _________.
Sources of ignition
,Where ___________ are used, they shall NOT extend from room to room or pass
through walls.
Flexible connectors
Illuminating appliances, clothes dryers, _________ and outdoor grills need not be
equipped with sediment traps.
Ranges
___________ must never be used for room heating.
Ranges, hot plates, OR laundry stoves
An approved manual shutoff shall be installed within ________ of the appliance it
serves.
6 feet
Generally, with aboveground containers ________ paint is preferred unless the
system is installed in an extremely cold climate.
Light reflecting
Vents or vent connectors for gas-fired toilet installations that are capable of being
contacted during casual use of the room in which the toilet is installed shall be
________ to prevent such contact.
, Protected or Shielded
Ventilating hoods and exhaust systems shall be _______ installed in commercial
applications and to vent industrial equipment.
Permitted to vent gas appliances
ASME containers 499 gallons w.c. and over that contain unodorized LP gas
products shall be marked "NOT ODORIZED" in letters _________ in height with
a contrasting background surrounded by a 1/2 inch rectangular border.
4 inches
Pressure relief valves shall be marked with ________.
1. the pressure in PSIG
2. rated relieving capacity
3. manufacturers name and catalog number
Brazing filler material for tubing joints shall have a melting point exceeding
_________.
1000 degrees Fahrenheit
Cylinders stored within a residential building, including the basement or any
storage area in a common basement of a multiple-family building and attached or
detached garages, shall be limited to cylinders each with a maximum water
QUESTIONS AND CORRECT ANSWERS GRADED
A+
ASME code refers to the __________ of the American Society of Mechanical
Engineers.
Boiler and pressure vessel code
A chimney for residential type or low heat appliances shall extend at least 2 feet
higher than any portion of a building with a horizontal distance of __________.
10 feet
The location where connections and disconnections are made or where LP-Gas
vented to the atmosphere in the course of transfer operations is known as
__________.
Point of transfer
Appliances or equipment that, because of their intended modes of use or operation,
are capable of providing sufficient thermal energy to ignite flammable gas-air
mixtures are known as _________.
Sources of ignition
,Where ___________ are used, they shall NOT extend from room to room or pass
through walls.
Flexible connectors
Illuminating appliances, clothes dryers, _________ and outdoor grills need not be
equipped with sediment traps.
Ranges
___________ must never be used for room heating.
Ranges, hot plates, OR laundry stoves
An approved manual shutoff shall be installed within ________ of the appliance it
serves.
6 feet
Generally, with aboveground containers ________ paint is preferred unless the
system is installed in an extremely cold climate.
Light reflecting
Vents or vent connectors for gas-fired toilet installations that are capable of being
contacted during casual use of the room in which the toilet is installed shall be
________ to prevent such contact.
, Protected or Shielded
Ventilating hoods and exhaust systems shall be _______ installed in commercial
applications and to vent industrial equipment.
Permitted to vent gas appliances
ASME containers 499 gallons w.c. and over that contain unodorized LP gas
products shall be marked "NOT ODORIZED" in letters _________ in height with
a contrasting background surrounded by a 1/2 inch rectangular border.
4 inches
Pressure relief valves shall be marked with ________.
1. the pressure in PSIG
2. rated relieving capacity
3. manufacturers name and catalog number
Brazing filler material for tubing joints shall have a melting point exceeding
_________.
1000 degrees Fahrenheit
Cylinders stored within a residential building, including the basement or any
storage area in a common basement of a multiple-family building and attached or
detached garages, shall be limited to cylinders each with a maximum water
