MKT 201 LATEST EVALUATION ALL TEST
QUESTIONS AND ANSWERS SURE A+
✔✔During pre-resection ligament balancing, before any cuts have been made, the
surgeon wishes to tighten both the extension and flexion gap by 2mm. - ✔✔move the
tibial component superior by 2mm
✔✔The surgeon user is attempting to complete the femoral bone registration process
and is unable to verify the bone registration in all three planes. What pre-operative step
could be associated with the failed result? - ✔✔Hip center CT landmark
✔✔based off the checkpoint page shown, what cuts can the surgeon make without
having to advance through an additional checkpoint page? - ✔✔distal and posterior
chamfer
✔✔The most common surgical approach for a total knee arthroplasty is medial
parapatellar. - ✔✔true
✔✔Tibial proximal resection landmarks are located approximately 2/3 posterior AP
distance of the lateral plateau - ✔✔true
, ✔✔While positioning the resection landmarks, which of the following should be
considered? - ✔✔avoid osteophytes and/or bony defects
✔✔The posterior condylar resection landmarks are used to define which of the
following? - ✔✔posterior condylar axis
✔✔The pre-resection balancing workflow does consider ligament tension prior to
trialing. - ✔✔true
✔✔The M/L axis of the tibia is defined by - ✔✔the rotational landmark
✔✔The steps for identifying and resolving a loose/bumped checkpoint are: 1. Walk
three planes in bone registration to confirm it is still accurate. 2. retighten the array. 3.
clear the associated bone registration, checkpoint, and patient landmarks. 4. recapture
the associated patient landmarks, checkpoint, and bone registration. - ✔✔false
✔✔During pre-operative planning, the amount the surgeon can externally rotate the
femoral component is limited by the PCA value. - ✔✔false
✔✔Which array does not need to be visible to see the Mako System position values in
the RIO setup page? - ✔✔End effector array
✔✔In bone preparation, standby mode means the surgeon is unable to enter the stereo-
tactics and start the saw - ✔✔false
✔✔During pre-operative planning, what is the maximum combined tibiofemoral flexion if
the tibial component size is > femoral component size - ✔✔10
✔✔The goal of a manual Triathlon procedure is to align the femoral component with
the? - ✔✔mechanical axis of the femur
✔✔The resection view feature in the implant planning page turns the implants on and
off the 3D bone model. - ✔✔false
✔✔When sizing the triathlon femoral component, which of the following is not
recommended? - ✔✔minimal bony coverage
✔✔The antlers for intra-incision bone pin placement need to be attached to the leg
holder during bone preparation. - ✔✔false
QUESTIONS AND ANSWERS SURE A+
✔✔During pre-resection ligament balancing, before any cuts have been made, the
surgeon wishes to tighten both the extension and flexion gap by 2mm. - ✔✔move the
tibial component superior by 2mm
✔✔The surgeon user is attempting to complete the femoral bone registration process
and is unable to verify the bone registration in all three planes. What pre-operative step
could be associated with the failed result? - ✔✔Hip center CT landmark
✔✔based off the checkpoint page shown, what cuts can the surgeon make without
having to advance through an additional checkpoint page? - ✔✔distal and posterior
chamfer
✔✔The most common surgical approach for a total knee arthroplasty is medial
parapatellar. - ✔✔true
✔✔Tibial proximal resection landmarks are located approximately 2/3 posterior AP
distance of the lateral plateau - ✔✔true
, ✔✔While positioning the resection landmarks, which of the following should be
considered? - ✔✔avoid osteophytes and/or bony defects
✔✔The posterior condylar resection landmarks are used to define which of the
following? - ✔✔posterior condylar axis
✔✔The pre-resection balancing workflow does consider ligament tension prior to
trialing. - ✔✔true
✔✔The M/L axis of the tibia is defined by - ✔✔the rotational landmark
✔✔The steps for identifying and resolving a loose/bumped checkpoint are: 1. Walk
three planes in bone registration to confirm it is still accurate. 2. retighten the array. 3.
clear the associated bone registration, checkpoint, and patient landmarks. 4. recapture
the associated patient landmarks, checkpoint, and bone registration. - ✔✔false
✔✔During pre-operative planning, the amount the surgeon can externally rotate the
femoral component is limited by the PCA value. - ✔✔false
✔✔Which array does not need to be visible to see the Mako System position values in
the RIO setup page? - ✔✔End effector array
✔✔In bone preparation, standby mode means the surgeon is unable to enter the stereo-
tactics and start the saw - ✔✔false
✔✔During pre-operative planning, what is the maximum combined tibiofemoral flexion if
the tibial component size is > femoral component size - ✔✔10
✔✔The goal of a manual Triathlon procedure is to align the femoral component with
the? - ✔✔mechanical axis of the femur
✔✔The resection view feature in the implant planning page turns the implants on and
off the 3D bone model. - ✔✔false
✔✔When sizing the triathlon femoral component, which of the following is not
recommended? - ✔✔minimal bony coverage
✔✔The antlers for intra-incision bone pin placement need to be attached to the leg
holder during bone preparation. - ✔✔false
