Missouri Hoisting Engineer Licensing
Exam Practice Questions And Correct
Answers (Verified Answers) Plus
Rationales 2026 Q&A | Instant
Download Pdf
1. What is the primary purpose of a hoisting engineer?
A. To design cranes
B. To operate hoisting equipment safely
C. To inspect buildings
D. To repair engines
Correct Answer: B
The hoisting engineer is responsible for the safe operation of lifting
and hoisting equipment.
2. Which document must be reviewed before lifting operations?
A. Payroll sheet
B. Load chart
C. Weather forecast only
, D. Equipment color code
Correct Answer: B
Load charts provide critical information about safe lifting capacities.
3. What is the first step before operating a hoist?
A. Start lifting immediately
B. Conduct a pre-operation inspection
C. Increase load limit
D. Remove safety devices
Correct Answer: B
A pre-operation inspection ensures equipment is safe to use.
4. What does OSHA stand for?
A. Occupational Safety and Hazard Administration
B. Occupational Safety and Health Administration
C. Official Safety and Hoisting Agency
D. Operational Safety Handling Authority
Correct Answer: B
OSHA sets and enforces workplace safety standards in the U.S.
5. Which factor most affects crane stability?
A. Paint color
B. Wind speed and load weight
C. Operator height
D. Fuel type
, Correct Answer: B
Wind and load weight significantly impact crane stability.
6. What is a sling used for?
A. Driving cranes
B. Securing and lifting loads
C. Fuel storage
D. Electrical grounding
Correct Answer: B
Slings are used to attach and lift loads safely.
7. What should you check on a wire rope before use?
A. Color
B. Diameter only
C. Broken wires and wear
D. Length markings only
Correct Answer: C
Wire ropes must be inspected for damage to prevent failure.
8. What is the meaning of SWL?
A. Safe Working Load
B. Standard Weight Limit
C. Secure Winch Level
D. System Work Load
Correct Answer: A
SWL is the maximum safe load a lifting device can handle.
, 9. Who is responsible for signaling during a lift?
A. Any bystander
B. Certified signal person
C. Truck driver
D. Supervisor only
Correct Answer: B
Only a trained signal person should guide crane operations.
10. What is the main hazard of overloading a crane?
A. Faster operation
B. Structural failure or tipping
C. Better efficiency
D. Reduced fuel use
Correct Answer: B
Overloading can cause crane collapse or tipping.
11. What is required before lifting a load near power lines?
A. Increase speed
B. Ensure proper clearance
C. Paint the crane
D. Remove warning signs
Correct Answer: B
Maintaining safe distance from power lines prevents electrocution.
12. What is rigging?
A. Driving trucks
Exam Practice Questions And Correct
Answers (Verified Answers) Plus
Rationales 2026 Q&A | Instant
Download Pdf
1. What is the primary purpose of a hoisting engineer?
A. To design cranes
B. To operate hoisting equipment safely
C. To inspect buildings
D. To repair engines
Correct Answer: B
The hoisting engineer is responsible for the safe operation of lifting
and hoisting equipment.
2. Which document must be reviewed before lifting operations?
A. Payroll sheet
B. Load chart
C. Weather forecast only
, D. Equipment color code
Correct Answer: B
Load charts provide critical information about safe lifting capacities.
3. What is the first step before operating a hoist?
A. Start lifting immediately
B. Conduct a pre-operation inspection
C. Increase load limit
D. Remove safety devices
Correct Answer: B
A pre-operation inspection ensures equipment is safe to use.
4. What does OSHA stand for?
A. Occupational Safety and Hazard Administration
B. Occupational Safety and Health Administration
C. Official Safety and Hoisting Agency
D. Operational Safety Handling Authority
Correct Answer: B
OSHA sets and enforces workplace safety standards in the U.S.
5. Which factor most affects crane stability?
A. Paint color
B. Wind speed and load weight
C. Operator height
D. Fuel type
, Correct Answer: B
Wind and load weight significantly impact crane stability.
6. What is a sling used for?
A. Driving cranes
B. Securing and lifting loads
C. Fuel storage
D. Electrical grounding
Correct Answer: B
Slings are used to attach and lift loads safely.
7. What should you check on a wire rope before use?
A. Color
B. Diameter only
C. Broken wires and wear
D. Length markings only
Correct Answer: C
Wire ropes must be inspected for damage to prevent failure.
8. What is the meaning of SWL?
A. Safe Working Load
B. Standard Weight Limit
C. Secure Winch Level
D. System Work Load
Correct Answer: A
SWL is the maximum safe load a lifting device can handle.
, 9. Who is responsible for signaling during a lift?
A. Any bystander
B. Certified signal person
C. Truck driver
D. Supervisor only
Correct Answer: B
Only a trained signal person should guide crane operations.
10. What is the main hazard of overloading a crane?
A. Faster operation
B. Structural failure or tipping
C. Better efficiency
D. Reduced fuel use
Correct Answer: B
Overloading can cause crane collapse or tipping.
11. What is required before lifting a load near power lines?
A. Increase speed
B. Ensure proper clearance
C. Paint the crane
D. Remove warning signs
Correct Answer: B
Maintaining safe distance from power lines prevents electrocution.
12. What is rigging?
A. Driving trucks
