INSTANT PDF DOWNLOAD CUSP - T&D
ACTUAL & EXAM
STUDY GUIDE COMPLETE QUESTIONS BANK
AND
CORRECT DETAILED CORRECT 100%
DETAILED ANSRS WITH RATIONALES ||
LATEST VERSION |
A high voltage utility or electrical company is authorized to use
Complex Lockout
(tag permitting) under what regulatory condition: - SELECTED
CORRECT 100% DETAILED ANSR 👀**** A variance application
has been approved by the provincial authority.
Utilities often use a permitting system due to special
circumstances of which conventional lockout is impracticable. The
following are justified approaches to this process: - SELECTED
CORRECT 100% DETAILED ANSR 👀**** 1. The isolation points
are located in remote areas with difficult or restricted access.
2. The length of time to perform the lockout is impracticable.
3. Excessive numbers of persons required to lockout.
Work on a distribution line must consider the following items when
performing isolation and de-energizing of the circuit.: -
SELECTED CORRECT 100% DETAILED ANSR 👀**** 1.
,Whether there are multiple sources of energy (loop feed) on the
circuit.
2. Is the line isolating device capable of interrupting load.
3. Is the line to be subject to inductive or capacitive charge.
According to the CAN/ULC S801, what is the LEAST DESIRABLE
type of fall protection: - SELECTED CORRECT 100% DETAILED
ANSR 👀**** Fall Arrest System (FAS)
Within Z259.14 standards fall restriction equipment (FRE) may
only be leather in subcomponents or elements that are NOT
exposed to: - SELECTED CORRECT 100% DETAILED ANSR
👀**** A dynamic load.
As per Z259 standards, energy absorbing lanyards shall be
classified according to their ability to absorb the kinetic energy
from a fall as follows: - SELECTED
CORRECT 100% DETAILED ANSR 👀**** Class E4 (4.0 kN) and
Class E6 (6.0 kN) energy absorbing lanyards.
As per CAN/ULC S801, on an electrical distribution overhead
utility line circuit, verification of voltage absence can be achieved
by: - SELECTED CORRECT 100% DETAILED ANSR 👀****
Using an approved voltage detector.
Isolation and tagging (no locks) is acceptable on an overhead
distribution circuit under some of the following conditions,
EXCEPT for: - SELECTED CORRECT 100% DETAILED ANSR
,👀**** The isolation can be operated from the ground directly at
the base of a structure.
Isolation and tagging (no locks) is acceptable for an overhead
distribution circuit under some of the following conditions: -
SELECTED CORRECT 100% DETAILED ANSR 👀**** 1. The
isolation point is a physical and visual like a line cut or riser
removed.
2. The isolation point can only be operated by the operating
authority or qualified worker.
3. The isolation point is protected from unauthorized access
such as vertical height spacing.
Consider that a circuit has been isolated, tagged and grounded.
workers returning the next day must: - SELECTED CORRECT
100% DETAILED ANSR 👀**** Visually check grounds to verify
they are in good order, secure and test for voltage.
For lockout purposes, energy isolating devices shall be labelled or
marked using a standardized nomenclature and format to indicate
their function. Identification shall include: - SELECTED
CORRECT 100% DETAILED ANSR 👀**** The equipment type,
energy type, and magnitude.
Utilities often use a permitting system due to special
circumstances of which conventional lockout is impracticable. The
following is NOT a justified approach to this process: -
, SELECTED CORRECT 100% DETAILED ANSR 👀**** The
isolation points are only simple single step actions.
Assuming that the fall protection system is correctly being used, in
what scenario might the worker still contact the ground if they fell:
- SELECTED
CORRECT 100% DETAILED ANSR 👀**** Working 16 feet up in
a bucket truck on distribution secondary services using a six foot
shock absorbing lanyard, connected to the approved bucket
anchor.
What is NOT defined as a requirement of temporary vertical life
lines as per
Z259 standards: - SELECTED CORRECT 100% DETAILED
ANSR 👀**** 100% polypropylene fibers provide the greatest
breaking strength.
Requirements of temporary vertical life lines, as per Z259
standards: -
SELECTED CORRECT 100% DETAILED ANSR 👀**** 1. Shall
be made from synthetic fibers with breaking strength of 27 kN or
greater.
2. They shall be free of splices and knots, except at the
terminations.
3. They shall be installed to protect against abrasion and sharp
edges.
ACTUAL & EXAM
STUDY GUIDE COMPLETE QUESTIONS BANK
AND
CORRECT DETAILED CORRECT 100%
DETAILED ANSRS WITH RATIONALES ||
LATEST VERSION |
A high voltage utility or electrical company is authorized to use
Complex Lockout
(tag permitting) under what regulatory condition: - SELECTED
CORRECT 100% DETAILED ANSR 👀**** A variance application
has been approved by the provincial authority.
Utilities often use a permitting system due to special
circumstances of which conventional lockout is impracticable. The
following are justified approaches to this process: - SELECTED
CORRECT 100% DETAILED ANSR 👀**** 1. The isolation points
are located in remote areas with difficult or restricted access.
2. The length of time to perform the lockout is impracticable.
3. Excessive numbers of persons required to lockout.
Work on a distribution line must consider the following items when
performing isolation and de-energizing of the circuit.: -
SELECTED CORRECT 100% DETAILED ANSR 👀**** 1.
,Whether there are multiple sources of energy (loop feed) on the
circuit.
2. Is the line isolating device capable of interrupting load.
3. Is the line to be subject to inductive or capacitive charge.
According to the CAN/ULC S801, what is the LEAST DESIRABLE
type of fall protection: - SELECTED CORRECT 100% DETAILED
ANSR 👀**** Fall Arrest System (FAS)
Within Z259.14 standards fall restriction equipment (FRE) may
only be leather in subcomponents or elements that are NOT
exposed to: - SELECTED CORRECT 100% DETAILED ANSR
👀**** A dynamic load.
As per Z259 standards, energy absorbing lanyards shall be
classified according to their ability to absorb the kinetic energy
from a fall as follows: - SELECTED
CORRECT 100% DETAILED ANSR 👀**** Class E4 (4.0 kN) and
Class E6 (6.0 kN) energy absorbing lanyards.
As per CAN/ULC S801, on an electrical distribution overhead
utility line circuit, verification of voltage absence can be achieved
by: - SELECTED CORRECT 100% DETAILED ANSR 👀****
Using an approved voltage detector.
Isolation and tagging (no locks) is acceptable on an overhead
distribution circuit under some of the following conditions,
EXCEPT for: - SELECTED CORRECT 100% DETAILED ANSR
,👀**** The isolation can be operated from the ground directly at
the base of a structure.
Isolation and tagging (no locks) is acceptable for an overhead
distribution circuit under some of the following conditions: -
SELECTED CORRECT 100% DETAILED ANSR 👀**** 1. The
isolation point is a physical and visual like a line cut or riser
removed.
2. The isolation point can only be operated by the operating
authority or qualified worker.
3. The isolation point is protected from unauthorized access
such as vertical height spacing.
Consider that a circuit has been isolated, tagged and grounded.
workers returning the next day must: - SELECTED CORRECT
100% DETAILED ANSR 👀**** Visually check grounds to verify
they are in good order, secure and test for voltage.
For lockout purposes, energy isolating devices shall be labelled or
marked using a standardized nomenclature and format to indicate
their function. Identification shall include: - SELECTED
CORRECT 100% DETAILED ANSR 👀**** The equipment type,
energy type, and magnitude.
Utilities often use a permitting system due to special
circumstances of which conventional lockout is impracticable. The
following is NOT a justified approach to this process: -
, SELECTED CORRECT 100% DETAILED ANSR 👀**** The
isolation points are only simple single step actions.
Assuming that the fall protection system is correctly being used, in
what scenario might the worker still contact the ground if they fell:
- SELECTED
CORRECT 100% DETAILED ANSR 👀**** Working 16 feet up in
a bucket truck on distribution secondary services using a six foot
shock absorbing lanyard, connected to the approved bucket
anchor.
What is NOT defined as a requirement of temporary vertical life
lines as per
Z259 standards: - SELECTED CORRECT 100% DETAILED
ANSR 👀**** 100% polypropylene fibers provide the greatest
breaking strength.
Requirements of temporary vertical life lines, as per Z259
standards: -
SELECTED CORRECT 100% DETAILED ANSR 👀**** 1. Shall
be made from synthetic fibers with breaking strength of 27 kN or
greater.
2. They shall be free of splices and knots, except at the
terminations.
3. They shall be installed to protect against abrasion and sharp
edges.
