• Wrong document? Swap it for free
  • Written by students who passed
  • Immediately available after payment
  • Read online or as PDF
Sell
Where do you study
Your language
Document preview thumbnail
Preview 3 out of 28 pages
Exam (elaborations)

2A751 EOC Study Guide Exam With Complete Solutions

Document preview thumbnail
Preview 3 out of 28 pages

2A751 EOC Study Guide Exam With Complete Solutions...

Content preview

2A751 EOC Study Guide Exam With
Complete Solutions

If tool length offset is not set during the programming phase, - ANSWER
manually set it at the machine before machining begins.

What is the difference between the staring and trailing sides of a die? - ANSWER
Starting side has three tapered threads; the trailing side has one tapered.

What causes excessive wear on the idler and drive wheels when using the
contour machine? - ANSWER Excessive tension

How do you place a precision level when you install a milling machine? -
ANSWER Longitudinally and laterally on the table.

When you grind out cracks to prepare for a weld repair, you should grind out all
cracks, except those - ANSWER that extend completely through.

What is the revolutions per minute you should use for machine reaming? -
ANSWER One-half the drilling speed.

The most efficient type of grinding wheel dresser for truing wheels used to
perform precision grinding is the - ANSWER diamond dresser

If the line rotates counterclockwise from the initial line, it is a - ANSWER positive
angle

What attaches the knee on the milling machine to the column? - ANSWER
dovetail ways.

To prevent damage to the universal punching and shearing machine, what must
you check to ensure the cutting capacity of the equipment is not exceeded? -
ANSWER Thickness and tensile strength of the material to be cut.

After you install a Heli-Coil, remember to properly remove the tang by - ANSWER
Breaking it off with a breakoff tool

,What do you use if you want to measure a height less than 1 inch with a Vernier
height gage? - ANSWER the offset attachment

Which item on the lathe tool determines chip formation and shear angle? -
ANSWER Face

TO machine a 1"-diameter steel rod with a selected cutting foot speed (CFS) of
80, you determine the lathe spindle revolutions per minute (RPM) with the
formula -- RPM = CFSx4/D, which results in an RPM of - ANSWER 320

Before you tighten or loosen the arbor nut on a horizontal milling machine, you
should - ANSWER Install the arbor support

If you allow the workpiece to stop without relieving the knurling tool pressure,
the - ANSWER work may spring

In oxyacetylene welding, the carburizing flame - ANSWER is the coolest flame

In shielded metal arc welding (SMAW), the difference between an E-7018 and an
E-10018 is - ANSWER the coating thickness

The feature of the quick-change tool post that provides a positive hold and
accurate setting for multiple tool holders is - ANSWER dovetailed surfaces

When performing a roller swaging operation, make sure you center the bearing
and - ANSWER make sure the bearing is square with the hole before you press is

An approximate method of aligning lathe centers is - ANSWER cricket mark

When heat treating nickel alloys, which process most closely resembles the
tempering process in steel? - ANSWER stress relieving

To eliminate the oxide film that results from welding aluminum alloys, use the
gas tungsten arc welding (GTAW) process with - ANSWER AC and Ar shielding
gas

The easiest way to control the weld when you use the GTAW to weld horizontal,
vertical, or overhead is to - ANSWER keep the molten pool small

When removing a broken plug in a cylinder, what should be done to prevent
damage to the cylinder? - ANSWER Pack the plug with grease to keep chips
from falling into the cylinder.

By using the micrometer carriage stop, you can position the carriage to a
tolerance within - ANSWER 0.0010"

, To prepare a chisel for cutting hard materials, grind the cutting edge included
angle to - ANSWER 70 degrees

The mist type coolant delivery system is used - ANSWER for high speed
machining only

To restore ductility to ferritic steel requires - ANSWER annealing

The position of a line at the start of an angle is known as the - ANSWER initial line

What type of end mill is best for interrupted cuts? - ANSWER helical fluted

When you press a plain bearing into a hole it's known as a - ANSWER bushing

When taking a finishing cut during straight turning operations, you should take a
shallow cut of about 1/4" - ANSWER to see if the diameter is correct

When silver soldering on thick metal or a large metal surface, preheat the metal
- ANSWER well away from the joint

To keep a pilot arc when you use alternating current (AC) for GTAW, use the -
ANSWER High-frequency switch

If line segments do not begin and end at the same point when creating geometry
for a computer numerical control, - ANSWER you have problems converting
them to tool paths

To reduce the HAZ, welding speeds are increased by - ANSWER ensuring the
edge preparation provides a good fit-up

When forging a workpiece, you should strike the final blows when the
temperature reaches - ANSWER 1300 degrees F

To obtain the correct diameter of a hole when using an inside micrometer, you
must add to the actual micrometer reading the length of the - ANSWER body and
extension rod.

What is the correct way to operate the telescoping gage when using it to gage a
hole? - ANSWER Set the gage in the hole, open it SLOWLY, and let the plungers
expand fully in the hole for measurement

On a contour machine, which term is used to describe the distance from the saw
band to the column? - ANSWER throat depth

In low carbon steels, to obtain an annealed condition, the steel should be cooled
in - ANSWER still air

Document information

Uploaded on
July 9, 2026
Number of pages
28
Written in
2025/2026
Type
Exam (elaborations)
Contains
Questions & answers
$19.49

Wrong document? Swap it for free Within 14 days of purchase and before downloading, you can choose a different document. You can simply spend the amount again.
Written by students who passed
Immediately available after payment
Read online or as PDF

Seller avatar
Reputation scores are based on the amount of documents a seller has sold for a fee and the reviews they have received for those documents. There are three levels: Bronze, Silver and Gold. The better the reputation, the more your can rely on the quality of the sellers work.
Zayla
3.2
(20)
Sold
163
Followers
13
Items
18619
Last sold
6 days ago



Why students choose Stuvia

Created by fellow students, verified by reviews

Quality you can trust: written by students who passed their tests and reviewed by others who've used these notes.

Didn't get what you expected? Choose another document

No worries! You can instantly pick a different document that better fits what you're looking for.

Pay as you like, start learning right away

No subscription, no commitments. Pay the way you're used to via credit card and download your PDF document instantly.

Student with book image

“Bought, downloaded, and aced it. It really can be that simple.”

Alisha Student

Working on your references?

Create accurate citations in APA, MLA and Harvard with our free citation generator.

Working on your references?

Frequently asked questions