PIVOT POINT CORRECT REVIEW EXAMS QUESTIONS
AND ANSWERS SURE A+
✔✔Base texturizing is performed up to: - ✔✔1" (2.5 cm) from scalp
✔✔A technique performed on the ends of the hair to allow for mobility, soften the ends
and blend the weight lines is called: - ✔✔End texturizing
✔✔Coarse hair should be texturized at least how far away from the scalp? - ✔✔1 1/2
(3.75 cm)
✔✔Sculpting one form is one area and another form elsewhere in the design refers to
sculpting a: - ✔✔Combination form
✔✔Which of the following forms adds volume and creates a rounded shape? -
✔✔Uniform
✔✔When sculpting a design with increase layers in the exterior, the resulting form is
generally: - ✔✔Elongated
✔✔The planar sculpting technique is used to create which of the following forms? -
✔✔Square
✔✔Which description is not incorporated with directional distribution? - ✔✔Straight
down
✔✔What technique is used when the lengths are too short to control between your
fingers? - ✔✔Over comb
✔✔To refine the perimeter in a shear-over-comb technique, designers use a: -
✔✔Taper comb
, ✔✔The technique used to position the shears parallel to the comb while moving both
upward in unison is called: - ✔✔Shear over comb
✔✔What technique is used to create a flat top? - ✔✔Clipper over comb
✔✔In gradation, the higher the angle of the comb, the greater amount of: -
✔✔Transparency
✔✔High gradation creates: - ✔✔Maximum transparency
✔✔ Sculpture transformation is all about changing the shape, surface texture and: -
✔✔structure
✔✔At the basic level of observation, a hair sculpture can be identified by observing the
outer boundary or silhouette known as the: - ✔✔Form line
✔✔The surface appearance of hair is referred to as: - ✔✔texture
✔✔What is meant by unactivated texture? - ✔✔smooth texture
✔✔The term used to describe the hair as the lengths lay or fall naturally over the curves
of the head is known as: - ✔✔Natural fall
✔✔When the hair is viewed abstractly as if it were projected at a 90 degree angle from
the various curves of the head, it is referred to as: - ✔✔Normal projection
✔✔The four basic forms are solid form, graduated form, increase layered form and: -
✔✔Uniformly layered form
✔✔Which of the following cutting tools is used to create a clean, blunt edge? -
✔✔shears
✔✔The movable blade of the shears is controlled by the: - ✔✔Thumb grip
✔✔To hold the comb and shears in the same hand without jeopardizing the clients
safety, release the thumb grip and: - ✔✔Close your palm over the shears
✔✔The type of shears that consist of one straight blade and one notched blade is
called: - ✔✔taper shears
AND ANSWERS SURE A+
✔✔Base texturizing is performed up to: - ✔✔1" (2.5 cm) from scalp
✔✔A technique performed on the ends of the hair to allow for mobility, soften the ends
and blend the weight lines is called: - ✔✔End texturizing
✔✔Coarse hair should be texturized at least how far away from the scalp? - ✔✔1 1/2
(3.75 cm)
✔✔Sculpting one form is one area and another form elsewhere in the design refers to
sculpting a: - ✔✔Combination form
✔✔Which of the following forms adds volume and creates a rounded shape? -
✔✔Uniform
✔✔When sculpting a design with increase layers in the exterior, the resulting form is
generally: - ✔✔Elongated
✔✔The planar sculpting technique is used to create which of the following forms? -
✔✔Square
✔✔Which description is not incorporated with directional distribution? - ✔✔Straight
down
✔✔What technique is used when the lengths are too short to control between your
fingers? - ✔✔Over comb
✔✔To refine the perimeter in a shear-over-comb technique, designers use a: -
✔✔Taper comb
, ✔✔The technique used to position the shears parallel to the comb while moving both
upward in unison is called: - ✔✔Shear over comb
✔✔What technique is used to create a flat top? - ✔✔Clipper over comb
✔✔In gradation, the higher the angle of the comb, the greater amount of: -
✔✔Transparency
✔✔High gradation creates: - ✔✔Maximum transparency
✔✔ Sculpture transformation is all about changing the shape, surface texture and: -
✔✔structure
✔✔At the basic level of observation, a hair sculpture can be identified by observing the
outer boundary or silhouette known as the: - ✔✔Form line
✔✔The surface appearance of hair is referred to as: - ✔✔texture
✔✔What is meant by unactivated texture? - ✔✔smooth texture
✔✔The term used to describe the hair as the lengths lay or fall naturally over the curves
of the head is known as: - ✔✔Natural fall
✔✔When the hair is viewed abstractly as if it were projected at a 90 degree angle from
the various curves of the head, it is referred to as: - ✔✔Normal projection
✔✔The four basic forms are solid form, graduated form, increase layered form and: -
✔✔Uniformly layered form
✔✔Which of the following cutting tools is used to create a clean, blunt edge? -
✔✔shears
✔✔The movable blade of the shears is controlled by the: - ✔✔Thumb grip
✔✔To hold the comb and shears in the same hand without jeopardizing the clients
safety, release the thumb grip and: - ✔✔Close your palm over the shears
✔✔The type of shears that consist of one straight blade and one notched blade is
called: - ✔✔taper shears
