OSHA 10 Final Exam Questions With 100% Verified Correct Answers.

19 inches or more - correct answers When two levels are a certain distance apart, employers have to provide a ladder or stairway between them. What is that distance? When the excavation is deeper than 4 feet - correct answers Under what conditions does your employer have to test for air hazards in a trench? No, they aren't required for any trench less than 20 feet deep. - correct answers Your company is digging a 16-foot-deep trench. Does your employer need to call a registered professional engineer? Make the trench wider at the top than at the bottom. - correct answers Which is a method to prevent cave-ins? It's loose or sandy, which means more safety measures are needed. - correct answers The competent person on the job site has let you know the soil you're working with is Type C soil. What type of soil is this? Have the authority to immediately correct hazards. - correct answers For excavations, a person is considered competent if they ... A piece of heavy equipment is working near the excavation edge. - correct answers Which of the following conditions could lead to a cave-in? Normal safety measures aren't enough to prevent a cave-in. - correct answers Why must a registered professional engineer design the safety systems for trenches deeper than 20 feet? 2 feet - correct answers How far away from the trench edge should materials, excess soil, and tools be kept? 18 inches - correct answers To keep heavy loads from falling in, how high does a trench protection system need to extend above a trench? Classifying the soil - correct answers A competent person is responsible for which of the following? None - correct answers You and your team are trenching in solid rock. What type of protective system do you need to install? A competent person should check the trench for hazards. - correct answers You've been installing sewer piping inside a trench, and a storm just passed through. What should you do? A possible cave-in - correct answers You notice that the bottom of the trench is cracking. What is this a sign of? Back right - correct answers Which area of a crane has the worst blind spot? Overloading - correct answers Of the following, which causes the most crane failures? Monthly - correct answers A competent person is responsible for which type of inspection? Voltage of the powerlines - correct answers What information does your employer need to use to decide how far to keep the crane from power lines? Establish a work zone. - correct answers What should you do when operating a crane around power lines? Manufacturer's instructions - correct answers Which of the following must be kept on the crane? Load moment indicator - correct answers Which system helps the crane operator avoid overloading the crane? It stabilizes the crane so it can safely hoist heavy loads. - correct answers What is the purpose of a counterweight? Only workers involved in the lift are allowed in fall zones. - correct answers Which of the following is true about fall zones? Competent person - correct answers Who should do the preshift inspection of a crane? Qualified person - correct answers Who should inspect a crane after it's been modified or repaired? Install barrier guards that show the swing radius of the crane. - correct answers What's the best way to avoid a crane's blind spot? Workers do most of the talking in safety meetings. - correct answers Which of the following is a sign of a good safety culture? Worker's compensation claims - correct answers Which of the following is an example of a lagging indicator? They give more information about hazards on site. - correct answers Why do near-miss reports help strengthen your workplace safety program? Install a muffler on it. - correct answers You notice that a piece of equipment is making a lot more noise than usual and could be a community nuisance. How could you reduce the noise? It measures how much you're doing to prevent incidents. - correct answers What does a leading indicator do? When someone almost trips on a cord in a walkway - correct answers When it comes to safety culture, what should you report? Use plywood to make a noise barrier around the equipment. - correct answers You're working with noisy equipment close to a residential neighborhood, and people are complaining. What is the best way to minimize your neighbors' noise exposure? Everyone - correct answers In a company with a good safety culture, who is responsible for finding and addressing hazards? Employers must give workers correctly fitting PPE. - correct answers What is an employer responsible for when it comes to PPE? It could get caught in the moving parts of tools or machinery. - correct answers Why is it dangerous to wear PPE that doesn't fit right? Informing the community about upcoming construction activities. - correct answers Which of the following is an example of being a good neighbor to the community? Give them a warning and send them home to get their boots. - correct answers A coworker has forgotten their steel-toed boots for their shift. What should your supervisor do? It measures how many incidents there have been and how severe they were. - correct answers What does a lagging indicator do? Identify it. - correct answers What is the first thing you need to do when solving a problem? So that you can figure out if the any part of the situation could make it more dangerous - correct answers Why is it important to consider contributing factors when you're problem-solving? A spontaneous group discussion to produce ideas and ways of solving problems - correct answers Brainstorming Something that helps cause a result - correct answers Contributing factor A safety tool that defines and controls hazards for a certain process, job, or procedure - correct answers Job safety analysis (JSA) Identifying the problem - correct answers You note that the unguarded gears on a table saw could snag workers' clothing or fingers. What problem-solving step is this part of? Bring it to your supervisor. - correct answers You've identified the best solution, but it's too big for your team to handle by yourselves. What should you do? The person who best understands the problem - correct answers Who would be the best choice to implement a solution? You might create more problems. - correct answers What can happen if you don't follow the problem-solving framework? Hold a team meeting about tool safety. - correct answers You know your coworker is misusing a power tool. What should you do? Be ready to address complications. - correct answers What should you do after choosing someone to implement a solution? Why is this hazard dangerous? - correct answers While you're identifying a problem, which of these should you consider? Evaluate the outcome. - correct answers What is the final step in the problem-solving framework? The parts of the situation that make it more dangerous - correct answers While you're identifying a problem, which of these should you analyze? Identify the problem. - correct answers When you're solving a problem, what should be the first step? What will happen if it goes wrong? - correct answers Which of these should you ask yourself while you're identifying a problem? How likely is it that an accident will happen? - correct answers Which of these should you ask yourself while you're identifying a problem? A document detailing a job's steps and potential hazards, and the safety controls needed - correct answers Job hazard analysis When people become so used to a deviant behavior that they don't consider it wrong anymore - correct answers Normalizing An individual who approaches a situation with reasonable caution and sensibly takes action - correct answers Reasonable person An OSHA program that gives workers and contractors the authority and responsibility to stop work if they observe unsafe conditions or behaviors on the job site. - correct answers Stop Work Authority (SWA) Accepting unsafe conditions as part of the job - correct answers Which of the following behaviors is an example of normalizing? October 5th (One month) - correct answers You report an unsafe work condition, and your employer fires you on September 5th. You decide to file a whistleblower complaint with OSHA. When do you need to do this by? Nothing. It's still unsafe to use the saw without safety glasses. - correct answers When your team needs to make quick cuts on a miter saw, they don't put on safety glasses. It's been two months and no one's had any eye injuries. What does this mean? Safety and health programs - correct answers Which of the following helps companies follow laws and regulations? Tag out the sledgehammer and alert your supervisor. - correct answers At the start of a shift, you grab a sledgehammer and notice the handle is starting to crack. What's the best thing to do? Tell your supervisor in private. - correct answers You've come across a safety concern on the job site but you don't want to speak up in front of everybody. What should you do? If you ask your supervisor for a safe chisel and they refuse - correct answers Your supervisor gives you a chiseling task and hands you a chisel with a mushroomed head. The head could splinter and send metal flying. At what point could you refuse this task? A story that workers can relate to - correct answers What makes safety messaging more memorable? offer to explain how a frayed cord burned you on your last job - correct answers in a safety meeting your supervisor starts talking about the hazards of frayed cords. On your last job, you got an electrical burn from a frayed cord. What should you do in the meeting? Safety messages should come from the employer and work their way down toward workers. - correct answers What is a good communication strategy for safety messages? Face-to-face - correct answers What's the best way to address a safety concern if you know it's going to be a difficult conversation? Concentrate on understanding what they're saying. - correct answers When you're in a conversation with a supervisor or coworker, what should you do? Ask your supervisor or employer to address the hazard. - correct answers What must you do before you can refuse hazardous work? Uncrossing your arms to show openness - correct answers Which of the following is an example of good body language in a difficult conversation? Whenever you see something wrong so you can keep everyone safe - correct answers When should you speak up about a workplace hazard?