NRVIA Technical RV Systems Inspection
Exam Practice Questions And Correct
Answers (Verified Answers) Plus
Rationale 2026 Q&A| Instant Download
Pdf
1. An RV inspector is evaluating a 120V AC distribution system in a
motorhome. The technician notices that multiple outlets in the galley
are not functioning, but the breaker has not tripped. What is the most
likely initial diagnostic step the inspector should take?
A. Replace the main breaker immediately
B. Test continuity of the GFCI outlet upstream of the affected receptacles
C. Increase breaker amperage rating
D. Replace all affected outlets without testing
Answer: B
The most likely cause is a tripped or failed upstream GFCI device that
protects downstream outlets. Testing continuity and resetting or replacing
the GFCI is the correct first diagnostic step before replacing components or
altering circuit protection.
2. During inspection of an RV propane system, a technician detects a
faint odor of gas near the regulator area. What is the safest and most
appropriate next action?
A. Tighten all visible fittings immediately
B. Use a flame to locate the leak source
,C. Shut off the propane supply and perform a leak test using approved
solution
D. Increase regulator pressure to clear the line
Answer: C
The correct safety protocol is to shut off the propane supply and perform a
controlled leak test using an approved non-flammable leak detection
solution to identify the source without introducing ignition risk.
3. A 12V DC system shows intermittent failure of interior lighting. Battery
voltage tests normal at rest but drops significantly under load. What is
the most likely cause?
A. Overcharged converter
B. High-resistance connection or failing battery under load
C. Faulty shore power connection
D. Oversized inverter installation
Answer: B
Voltage drop under load typically indicates a weak battery or high-
resistance connection such as corroded terminals or loose grounds, even
when static voltage appears normal.
4. While inspecting an RV roof, the technician finds soft spots around the
air conditioning unit mounting area. What is the most appropriate
conclusion?
A. Normal flexing of roof membrane
B. Structural water intrusion and potential rot in roof decking
C. Cosmetic sealant discoloration only
D. Over-tightened HVAC mounting bolts only
Answer: B
Soft spots indicate likely moisture intrusion leading to structural
deterioration of roof decking, which requires immediate investigation and
potential repair.
, 5. An RV water heater operates on both propane and electric modes.
Electric mode fails while propane mode functions normally. What is
the most probable cause?
A. Faulty thermostat or heating element on electric circuit
B. Empty propane tank
C. Blocked burner jet
D. Low water pressure in tank
Answer: A
Since propane operation is functional, the issue is isolated to the electric
heating system, commonly caused by a failed element or thermostat.
6. A technician observes that an RV chassis battery is draining overnight
when parked. Which component is the most likely parasitic load
source?
A. Roof air conditioner
B. Carbon monoxide detector or parasitic 12V draw
C. Tire pressure
D. Propane furnace burner
Answer: B
Safety devices and control boards often draw small continuous loads, and
faults or aging systems can cause excessive parasitic drain on chassis
batteries.
7. During brake inspection on a towable RV, uneven brake wear is
observed on one axle. What is the most likely cause?
A. Overinflated tires
B. Faulty brake controller calibration or wiring imbalance
C. Excessive engine braking
D. Incorrect propane regulator pressure
, Answer: B
Uneven braking typically indicates electrical imbalance or controller
miscalibration affecting brake magnet engagement across axles.
8. An RV refrigerator is not cooling properly on electric mode but works
on propane. What is the most likely issue?
A. Faulty 120V heating element or control board
B. Empty refrigerant tank
C. Damaged propane line
D. Overfilled coolant reservoir
Answer: A
Absorption refrigerators rely on separate heat sources; failure in electric
mode typically indicates a faulty heating element or control system.
9. While inspecting slide-out operation, the technician notices jerky
movement and audible strain. What is the most appropriate initial
inspection focus?
A. Roof seal condition
B. Slide-out motor, alignment, and lubrication system
C. Tire pressure
D. Water pump operation
Answer: B
Jerky slide operation usually indicates mechanical resistance, often due to
misalignment, poor lubrication, or motor strain.
10. A GFCI outlet repeatedly trips immediately after reset. What is
the most likely cause?
A. Normal operation
B. Ground fault or moisture intrusion in downstream circuit
C. High propane pressure
D. Low tire pressure
Exam Practice Questions And Correct
Answers (Verified Answers) Plus
Rationale 2026 Q&A| Instant Download
1. An RV inspector is evaluating a 120V AC distribution system in a
motorhome. The technician notices that multiple outlets in the galley
are not functioning, but the breaker has not tripped. What is the most
likely initial diagnostic step the inspector should take?
A. Replace the main breaker immediately
B. Test continuity of the GFCI outlet upstream of the affected receptacles
C. Increase breaker amperage rating
D. Replace all affected outlets without testing
Answer: B
The most likely cause is a tripped or failed upstream GFCI device that
protects downstream outlets. Testing continuity and resetting or replacing
the GFCI is the correct first diagnostic step before replacing components or
altering circuit protection.
2. During inspection of an RV propane system, a technician detects a
faint odor of gas near the regulator area. What is the safest and most
appropriate next action?
A. Tighten all visible fittings immediately
B. Use a flame to locate the leak source
,C. Shut off the propane supply and perform a leak test using approved
solution
D. Increase regulator pressure to clear the line
Answer: C
The correct safety protocol is to shut off the propane supply and perform a
controlled leak test using an approved non-flammable leak detection
solution to identify the source without introducing ignition risk.
3. A 12V DC system shows intermittent failure of interior lighting. Battery
voltage tests normal at rest but drops significantly under load. What is
the most likely cause?
A. Overcharged converter
B. High-resistance connection or failing battery under load
C. Faulty shore power connection
D. Oversized inverter installation
Answer: B
Voltage drop under load typically indicates a weak battery or high-
resistance connection such as corroded terminals or loose grounds, even
when static voltage appears normal.
4. While inspecting an RV roof, the technician finds soft spots around the
air conditioning unit mounting area. What is the most appropriate
conclusion?
A. Normal flexing of roof membrane
B. Structural water intrusion and potential rot in roof decking
C. Cosmetic sealant discoloration only
D. Over-tightened HVAC mounting bolts only
Answer: B
Soft spots indicate likely moisture intrusion leading to structural
deterioration of roof decking, which requires immediate investigation and
potential repair.
, 5. An RV water heater operates on both propane and electric modes.
Electric mode fails while propane mode functions normally. What is
the most probable cause?
A. Faulty thermostat or heating element on electric circuit
B. Empty propane tank
C. Blocked burner jet
D. Low water pressure in tank
Answer: A
Since propane operation is functional, the issue is isolated to the electric
heating system, commonly caused by a failed element or thermostat.
6. A technician observes that an RV chassis battery is draining overnight
when parked. Which component is the most likely parasitic load
source?
A. Roof air conditioner
B. Carbon monoxide detector or parasitic 12V draw
C. Tire pressure
D. Propane furnace burner
Answer: B
Safety devices and control boards often draw small continuous loads, and
faults or aging systems can cause excessive parasitic drain on chassis
batteries.
7. During brake inspection on a towable RV, uneven brake wear is
observed on one axle. What is the most likely cause?
A. Overinflated tires
B. Faulty brake controller calibration or wiring imbalance
C. Excessive engine braking
D. Incorrect propane regulator pressure
, Answer: B
Uneven braking typically indicates electrical imbalance or controller
miscalibration affecting brake magnet engagement across axles.
8. An RV refrigerator is not cooling properly on electric mode but works
on propane. What is the most likely issue?
A. Faulty 120V heating element or control board
B. Empty refrigerant tank
C. Damaged propane line
D. Overfilled coolant reservoir
Answer: A
Absorption refrigerators rely on separate heat sources; failure in electric
mode typically indicates a faulty heating element or control system.
9. While inspecting slide-out operation, the technician notices jerky
movement and audible strain. What is the most appropriate initial
inspection focus?
A. Roof seal condition
B. Slide-out motor, alignment, and lubrication system
C. Tire pressure
D. Water pump operation
Answer: B
Jerky slide operation usually indicates mechanical resistance, often due to
misalignment, poor lubrication, or motor strain.
10. A GFCI outlet repeatedly trips immediately after reset. What is
the most likely cause?
A. Normal operation
B. Ground fault or moisture intrusion in downstream circuit
C. High propane pressure
D. Low tire pressure
