AUMT QUIZ 1 Updated Exam 2026 WITH Recent Newest
Verified And Well Analyzed Exam Questions (Actual Exam
2026-2027) Correct Detailed & Verified ANSWERS (100%
Accurate Solutions) ALREADY GRADED A+||NEWEST
VERSION Of The Exam Guarantee Pass!!
Minimum concentration of antifreeze is - ANSWERS-50/50
The tenth character in the VIN is the _____. - ANSWERS-Year
Radial tires should be rotated every _____ miles after being initially rotated at 7,500
miles. - ANSWERS-15000
Directional tires are being discussed. Technician A says directional tires should not be
cross rotated, but rotated front to rear. Technician B cross rotates the tires by
dismounting them from the rims, flipping them over and remounting. Who is correct? -
ANSWERS-Both Technicians
The VIN number for vehicles built in the United States begins with _____. - ANSWERS-
1
If a ball joint has a threaded plug, the plug can be removed and a _____ fitting installed
that will allow the ball joint to be greased periodically. - ANSWERS-Zerk
In most automotive applications, the water pump is driven by the ______. - ANSWERS-
CRANKshaft
Hose sizes are based on their - ANSWERS-Inside Diameter
, For every 1 pound of pressure put on engine coolant, the boiling point of the coolant is
raised about _____ degrees Fahreheit degrees (_____ degrees Celsius). - ANSWERS-
3.25 (1.8)
A 3/8 inch UNC bolt is being discussed. Technician A says that the bolt diameter is 3/8
inch and that it has 16 threads per inch. Technician B says that the bolt meets the
measurement standards developed by the University of North Carolina. Who is correct?
- ANSWERS-A only
A dial caliper is accurate to _____ inch. - ANSWERS-0.001
A measurement must be made within one ten-thousandth of an inch. Technician A uses
a machinist's rule. Technician B uses a standard micrometer. Who is correct? -
ANSWERS-Neither A or B
A straightedge and feeler gauge are used to measure _____. - ANSWERS-Warpage
Engine power is transferred to an automatic transmission through a ______. -
ANSWERS-Torque Converter
An extractor is used for removing broken ______. - ANSWERS-Bolts
Hybrid vehicles are being discussed. Technician A says a hybrid can run on electric
power or on the internal combustion motor, but never on both. Technician B says the
internal combustion engines used in hybrids are specially designed to be assisted by
electric power and as a result are more fuel efficient and cleaner than conventional
engines. Who is correct? - ANSWERS-Both Technicians
Hybrid vehicles are being discussed. Technician A says the hybrid batteries are
recharged by the engine during normal driving. Technician B say the batteries are
recharged when the brakes are applied as the vehicle slows down. Who is correct? -
ANSWERS-Technician B
Verified And Well Analyzed Exam Questions (Actual Exam
2026-2027) Correct Detailed & Verified ANSWERS (100%
Accurate Solutions) ALREADY GRADED A+||NEWEST
VERSION Of The Exam Guarantee Pass!!
Minimum concentration of antifreeze is - ANSWERS-50/50
The tenth character in the VIN is the _____. - ANSWERS-Year
Radial tires should be rotated every _____ miles after being initially rotated at 7,500
miles. - ANSWERS-15000
Directional tires are being discussed. Technician A says directional tires should not be
cross rotated, but rotated front to rear. Technician B cross rotates the tires by
dismounting them from the rims, flipping them over and remounting. Who is correct? -
ANSWERS-Both Technicians
The VIN number for vehicles built in the United States begins with _____. - ANSWERS-
1
If a ball joint has a threaded plug, the plug can be removed and a _____ fitting installed
that will allow the ball joint to be greased periodically. - ANSWERS-Zerk
In most automotive applications, the water pump is driven by the ______. - ANSWERS-
CRANKshaft
Hose sizes are based on their - ANSWERS-Inside Diameter
, For every 1 pound of pressure put on engine coolant, the boiling point of the coolant is
raised about _____ degrees Fahreheit degrees (_____ degrees Celsius). - ANSWERS-
3.25 (1.8)
A 3/8 inch UNC bolt is being discussed. Technician A says that the bolt diameter is 3/8
inch and that it has 16 threads per inch. Technician B says that the bolt meets the
measurement standards developed by the University of North Carolina. Who is correct?
- ANSWERS-A only
A dial caliper is accurate to _____ inch. - ANSWERS-0.001
A measurement must be made within one ten-thousandth of an inch. Technician A uses
a machinist's rule. Technician B uses a standard micrometer. Who is correct? -
ANSWERS-Neither A or B
A straightedge and feeler gauge are used to measure _____. - ANSWERS-Warpage
Engine power is transferred to an automatic transmission through a ______. -
ANSWERS-Torque Converter
An extractor is used for removing broken ______. - ANSWERS-Bolts
Hybrid vehicles are being discussed. Technician A says a hybrid can run on electric
power or on the internal combustion motor, but never on both. Technician B says the
internal combustion engines used in hybrids are specially designed to be assisted by
electric power and as a result are more fuel efficient and cleaner than conventional
engines. Who is correct? - ANSWERS-Both Technicians
Hybrid vehicles are being discussed. Technician A says the hybrid batteries are
recharged by the engine during normal driving. Technician B say the batteries are
recharged when the brakes are applied as the vehicle slows down. Who is correct? -
ANSWERS-Technician B
