MKC SWE Exam | Questions and Answers |
Verified Solutions | 2026 Edition | Pass
Guaranteed
Save
Practice questions for this set
Learn 1 /7 Study using Learn
Carryover could result. Discoloration or higher oil level could indicate
presence of condensed liquid
Choose an answer
1 P100 dipstick location 2 If air compressor oil level is too high.
3 Meter calibration interval 4 P6 Specs
Don't know?
Terms in this set (106)
, P100 dipstick location 2 dipsticks on each side of the engine
P100 engine specification Yanmar L100AE/EE air cooled, single cylinder, 4
stroke, diesel F-76 or JP-5
P100 Specifications 164lbs of wet weight, 1.45 Gallons of fuel 2.75 hrs of
run time 100GPM@83PSI@20ft lift, packing screw 6"
long 9/16 wrench, drip rate 5-50 DPM
Securing P100 turn speed to low, run with no load for aprox 5
minutes to allow it to cool off
P6 Specs Honda GX200, 6.5HP, 3Gal tank, 4hour run time, 86
octane gas,unit 60lbs, kit 120lbs
P6 Dry run time This pump is equipped with a mechanical lip seal.
Avoid running the pump dry or at high speed if
there is no discharge water. If there is no discharge
flow after two minutes, shut down the engine and
check for leaks in the suction hose
P6 Maintenance • Automotive 4 stroke SAE 10W-30 detergent oil is
recommended for the engine for general
operation. See the Honda GX200 Engine Owner's
Manual for oil recommendations for adverse
operating conditions. • Check the engine oil level
prior to each use. Add oil as necessary. • Change
the engine oil after the first 20 hours; then every
100 hours, or 6 months thereafter. • Replace the
inline fuel filter after the first 20 hours; then every
100 hours, or 6 months thereafter.
P6 time between fuel tank changes 30 seconds
Verified Solutions | 2026 Edition | Pass
Guaranteed
Save
Practice questions for this set
Learn 1 /7 Study using Learn
Carryover could result. Discoloration or higher oil level could indicate
presence of condensed liquid
Choose an answer
1 P100 dipstick location 2 If air compressor oil level is too high.
3 Meter calibration interval 4 P6 Specs
Don't know?
Terms in this set (106)
, P100 dipstick location 2 dipsticks on each side of the engine
P100 engine specification Yanmar L100AE/EE air cooled, single cylinder, 4
stroke, diesel F-76 or JP-5
P100 Specifications 164lbs of wet weight, 1.45 Gallons of fuel 2.75 hrs of
run time 100GPM@83PSI@20ft lift, packing screw 6"
long 9/16 wrench, drip rate 5-50 DPM
Securing P100 turn speed to low, run with no load for aprox 5
minutes to allow it to cool off
P6 Specs Honda GX200, 6.5HP, 3Gal tank, 4hour run time, 86
octane gas,unit 60lbs, kit 120lbs
P6 Dry run time This pump is equipped with a mechanical lip seal.
Avoid running the pump dry or at high speed if
there is no discharge water. If there is no discharge
flow after two minutes, shut down the engine and
check for leaks in the suction hose
P6 Maintenance • Automotive 4 stroke SAE 10W-30 detergent oil is
recommended for the engine for general
operation. See the Honda GX200 Engine Owner's
Manual for oil recommendations for adverse
operating conditions. • Check the engine oil level
prior to each use. Add oil as necessary. • Change
the engine oil after the first 20 hours; then every
100 hours, or 6 months thereafter. • Replace the
inline fuel filter after the first 20 hours; then every
100 hours, or 6 months thereafter.
P6 time between fuel tank changes 30 seconds
