MP100 Cycle 1 Test (MP100) Questions
and Answers Exam
CONSOLE LAYOUTS - ANSWER>>Split and in line
Signal-to-noise ratio (SNR) - ANSWER>>the level of signal relative to noise floor
Wet to dry ratio - ANSWER>>ratio describing signal before and after time based
processing
headroom - ANSWER>>the area between nominal level and distortion
analog = between 0dbvu-20dbvu
digital= -20dbfs to 0dbfs
stop button (tape machine) - ANSWER>>initializes tape machine
alternative terms for headphones - ANSWER>>foldbacks/cues
console method question #1 - ANSWER>>what inputs does the console offer?
console method question #2 - ANSWER>>how do i access any input into any fader
console method question #3 - ANSWER>>which console inputs are the MTR
outputs connected to?
console method #4 - ANSWER>>how do i direct the output of the faders to the
multitrack bus or stereo bus?
aux method question #1 - ANSWER>>what fader or path should the split be taken
from?
aux method question #2 - ANSWER>>should the split be pre or post fader?
, which path should aux split be taken from - ANSWER>>monitor path always
why should aux split be pre fader? - ANSWER>>to adjust faders without changing
headphone mix
why should aux split be post fader? - ANSWER>>to maintain wet to dry ratio with
time based processors
2 most common meters - ANSWER>>LED and VU
what measurement does LED meter take? - ANSWER>>peak
what measurement does VU meter take? - ANSWER>>RMS (root mean square)
what does peak measure? - ANSWER>>the highest transient
what does VU measure? - ANSWER>>the average
how to send any fader to the stereo bus on the SSL origin - ANSWER>>LF to mix or
SF to mix
what is a normal? - ANSWER>>pre existing connection between 2 points
full normal - ANSWER>>breaks at input and output
half normal - ANSWER>>breaks only at input
open normal - ANSWER>>no pre existing connection
mult - ANSWER>>copies signal to multiple outputs
what are the 2 components to an insert - ANSWER>>send and return
do inserts come before or after fader? - ANSWER>>always before the fader
and Answers Exam
CONSOLE LAYOUTS - ANSWER>>Split and in line
Signal-to-noise ratio (SNR) - ANSWER>>the level of signal relative to noise floor
Wet to dry ratio - ANSWER>>ratio describing signal before and after time based
processing
headroom - ANSWER>>the area between nominal level and distortion
analog = between 0dbvu-20dbvu
digital= -20dbfs to 0dbfs
stop button (tape machine) - ANSWER>>initializes tape machine
alternative terms for headphones - ANSWER>>foldbacks/cues
console method question #1 - ANSWER>>what inputs does the console offer?
console method question #2 - ANSWER>>how do i access any input into any fader
console method question #3 - ANSWER>>which console inputs are the MTR
outputs connected to?
console method #4 - ANSWER>>how do i direct the output of the faders to the
multitrack bus or stereo bus?
aux method question #1 - ANSWER>>what fader or path should the split be taken
from?
aux method question #2 - ANSWER>>should the split be pre or post fader?
, which path should aux split be taken from - ANSWER>>monitor path always
why should aux split be pre fader? - ANSWER>>to adjust faders without changing
headphone mix
why should aux split be post fader? - ANSWER>>to maintain wet to dry ratio with
time based processors
2 most common meters - ANSWER>>LED and VU
what measurement does LED meter take? - ANSWER>>peak
what measurement does VU meter take? - ANSWER>>RMS (root mean square)
what does peak measure? - ANSWER>>the highest transient
what does VU measure? - ANSWER>>the average
how to send any fader to the stereo bus on the SSL origin - ANSWER>>LF to mix or
SF to mix
what is a normal? - ANSWER>>pre existing connection between 2 points
full normal - ANSWER>>breaks at input and output
half normal - ANSWER>>breaks only at input
open normal - ANSWER>>no pre existing connection
mult - ANSWER>>copies signal to multiple outputs
what are the 2 components to an insert - ANSWER>>send and return
do inserts come before or after fader? - ANSWER>>always before the fader
